User Guide

J300P-2
Flange Yokes
Snap Ring Design
Figure 1
Figure 2
Figure 3
6
Important: See Safety Information in General Information Section (J300P-GI)
• Part is discontinued  Part is available until supply is exhausted  Not sold separately
A B - Bolt Holes C G
Flange or Bolt Diameter Number Pilot Diameter Flange Illustration Spicer
Swing Circle D-Drilled of M-Male Face to Figure Part
Diameter Diameter
T-Tapped Holes F-Female Centerline Number
1310 SERIES (Continued) E-3.469 D-1.062 USE KIT NO. 5-153X, 5-785X, 5-810X, 5-1200X
4.500 3.500 .500-D 4 2.000F 1.650 1 2-2-939
Bolt holes are equally spaced. Part has hole thru center.
4.580 3.750 .440-D 4 2.750M 1.190 1 2-2-1039•
4.678 3.740 .469-D 4 2.558M 1.781 1 2-2-1729
4.625 3.750 .406-D 4 2.559M 1.772 1 2-2-1799
10 mm bolt holes, equally spaced
4.625 3.750 .438-D 4 2.750M 1.375 1 2-2-479
4.719 3.750 .481-D 4 2.558M 1.781 1 2-2-1949
12 mm bolt holes equally spaced.
4.740 3.740 .478-D 4 1.964M 1.780 1 2-2-2029
Bolts holes are equally spaced
4.750 3.750 .503-D 4 2.750M 2.000 1 2-2-1789
10 mm bolt holes, equally spaced
4.906 3.937 .489-D 4 2.162F 1.930 1 2-2-1989
Bolt holes are equally spaced. Part has hole thru center.
5.219 4.250 .484-D 4 2.000F 1.625 1 2-2-1379
Bolt holes are equally spaced. Part has hole thru center.
5.750 4.750 .507-D 4 3.750M 1.375 1 2-2-579
1330 SERIES E-3.875 D-1.062 USE KIT NO. 5-213X, 5-790X, 5-812X, 5-1203X
3.880 3.000 .487-D 4 2.436F 1.618 1 2-2-01474
4.469 3.500 .484-D 4 2.000F 1.625 1 2-2-949
Bolts holes are equally spaced
4.528 3.661 .446-D 4 1.811M 1.653 1 5001904
5001904 was replaced by 2-2-01904
4.528 3.661 .446-D 4 1.811M 1.653 1 2-2-01904
4.625 3.750 .438-D 4 2.750M 1.562 1 2-2-1209
4.625 3.750 .438-D 4 2.750M 1.562 1 2-2-489
4.960 3.938 .489-D 4 2.161F 1.930 1 2-2-1879•
5.118 3.674 .482-D 4 1.811M 1.653 1 2-2-02768
Bolts holes are equally spaced
5.156 4.250 .453-D 4 3.125F 1.688 1 2-2-1399
Bolts holes are equally spaced
Continued on next page