User Manual
05
SPEX BACK SUPPORT USER MANUAL
8
WWW.SPEXSEATING.COM
SINGLE-
MOUNT
Installing Single/Dual Mount
Adjust the Back Support mounting brackets to allow the Back
Support to move freely between the wheelchair canes.
Approximately 5/8” (16mm) of clearance between the cane and
pin is required.
Apply enough tension to the fasteners to prevent the brackets
from moving freely during the set
-up.
Tools required: 4mm, 5mm Hex (Allen) Key, 13mm spanner/
wrench.
1.
2.
3.
4.
Attach the brackets to the canes, using the clamps and
fasteners.
Partially insert the rear fastener, slide the clamp under-
neath fastener head, and insert and tighten both fasten-
ers to secure the bracket in place.
5.
Ensure that both the left
and right hardware compo-
nents are level.
Tighten both fasteners.
Spex recommends 5Nm (4
ft-lb) of torque.
6.
7.
Note the dierences between the left and right hardware con-
gurations. Ensure the hardware is installed to the correct side.
C O N F I D E N T I A L
THIS INFORMATION IS HIGHLY CONFIDENTIAL AND IS THE
EXCLUSIVE PROPERTY OF MEDIFAB LIMITED.
THIS DRAWING MUST NOT BE USED FOR ANY PURPOSE
OTHER THAN THAT EXPRESSLY PERMITTED BY THE OWNERS
AND MUST BE RETURNED TO MEDIFAB LIMITED.
1
1X
5
2X
2
1X
6
2X
3
2X
4
2X
ITEM NO.
PART NUMBER
Description 1
QTY.
1
A-00115
2pt Mount Asy - Left
1
2
A-00114
2pt Inner Bracket - Left
1
3
0057-0FLT-SS-M8x16x1.2
Washer Flat M8 x 16 x 1.2 S/S
2
4
0054-NTND-M8SS
M8 Dome Nyloc Nut S/S 304
2
5
P-00406
M8 Square Neck Bolt
2
6
0057-0SPR-SS4-M8
Washer Spring M8 S/S T304
2
A01
2 Point Backrest Mount - LEFT
29/06/2016
Mike Kearins
A3
SHEET
1 OF 2
DWG NO.
DESCRIPTION:
REVISION:
MATERIAL:
SIGNATURE
NAME
DEBURR AND BREAK SHARP EDGES
FINISH:
APPV'D
CHK'D
DRAWN
SCALE:1:2
DATE
mike.kearins - Wednesday, 29 June 2016 12:38:16 p.m. - C:\Medifab Vault\Products\New Spex\CAD\Backrest\
WEIGHT:
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
LINEAR TOLERANCES:
+
0.2mm
ANGULAR: TOLERANCES:
+
0.5°
g
32 Detroit Drive
iZone Business Hub
Rolleston 7675
New Zealand
Phone +64 3 307 9790
2
1
1
2
Backrest mounting hardware
PART NO.
ERP NO.
A-00531
ECN
CHANGE
FOR INTERNAL REVIEW ONLY
A-00531
C O N F I D E N T I A L
THIS INFORMATION IS HIGHLY CONFIDENTIAL AND IS THE
EXCLUSIVE PROPERTY OF MEDIFAB LIMITED.
THIS DRAWING MUST NOT BE USED FOR ANY PURPOSE
OTHER THAN THAT EXPRESSLY PERMITTED BY THE OWNERS
AND MUST BE RETURNED TO MEDIFAB LIMITED.
2
1X
6
2X
4
2X
3
2X
1
1X
5
2X
ITEM NO.
PART NUMBER
Description 1
QTY.
1
A-00112
2pt Mount Asy - Right
1
2
A-00113
2pt Inner Bracket - Right
1
3
0057-0FLT-SS-M8x16x1.2
Washer Flat M8 x 16 x 1.2 S/S
2
4
0054-NTND-M8SS
M8 Dome Nyloc Nut S/S 304
2
5
P-00406
M8 Square Neck Bolt
2
6
0057-0SPR-SS4-M8
Washer Spring M8 S/S T304
2
A01
2 Point Backrest Mount - RIGHT
29/06/2016
Mike Kearins
A3
SHEET
1 OF 2
DWG NO.
DESCRIPTION:
REVISION:
MATERIAL:
SIGNATURE
NAME
DEBURR AND BREAK SHARP EDGES
FINISH:
APPV'D
CHK'D
DRAWN
SCALE:1:2
DATE
mike.kearins - Wednesday, 29 June 2016 12:35:21 p.m. - C:\Medifab Vault\Products\New Spex\CAD\Backrest\
WEIGHT:
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
LINEAR TOLERANCES:
+
0.2mm
ANGULAR: TOLERANCES:
+
0.5°
g
32 Detroit Drive
iZone Business Hub
Rolleston 7675
New Zealand
Phone +64 3 307 9790
2
1
1
2
Backrest mounting hardware
PART NO.
ERP NO.
A-00532
ECN
CHANGE
FOR PROTOTYPE REVIEW
A-00532
RIGHT
LEFT
SINGLE-
MOUNT
D UA L-
MOUNT
D UA L-
MOUNT