User Manual
05
MANUEL DE L’UTILISATEUR DE L’APPUI-DOS SPEX 29
WWW.SPEXSEATING.COM
1 POINT
Installation à 1 pt/2 pts
Réglez les supports de xation de l’appui-dos de façon à ce qu’il
puisse être déplacé librement entre les tubes du fauteuil roulant.
Un jeu d’environ 16 mm (5/8 po) entre le tube et la goupille est
requis.
Appliquez susamment de tension aux attaches an
d’empêcher que les supports de xation se déplacent librement
lors du montage.
Outils requis : clés Allen de 4 mm et 5 mm, clé à ergots de 13 mm.
1.
2.
3.
4.
Attachez les supports de xation aux tubes à l’aide des
brides de serrage et des attaches.
Insérez partiellement l’attache arrière, glissez la rondelle
de serrage sous la tête de l’attache, puis insérez et serrez
les deux attaches pour xer le support de xation en
place.
5.
Assurez-vous que les com-
posants des ferrures droit et
gauche sont de niveau.
Serrez les deux attaches.
Spex recommande un
couple de serrage de 5 N.m
(4 lb.pi).
6.
7.
Notez les diérences de conguration entre les ferrures de
gauche et de droite. Assurez-vous que chaque ferrure est in-
stallée du bon côté
C O N F I D E N T I A L
THIS INFORMATION IS HIGHLY CONFIDENTIAL AND IS THE
EXCLUSIVE PROPERTY OF MEDIFAB LIMITED.
THIS DRAWING MUST NOT BE USED FOR ANY PURPOSE
OTHER THAN THAT EXPRESSLY PERMITTED BY THE OWNERS
AND MUST BE RETURNED TO MEDIFAB LIMITED.
1
1X
5
2X
2
1X
6
2X
3
2X
4
2X
ITEM NO.
PART NUMBER
Description 1
QTY.
1
A-00115
2pt Mount Asy - Left
1
2
A-00114
2pt Inner Bracket - Left
1
3
0057-0FLT-SS-M8x16x1.2
Washer Flat M8 x 16 x 1.2 S/S
2
4
0054-NTND-M8SS
M8 Dome Nyloc Nut S/S 304
2
5
P-00406
M8 Square Neck Bolt
2
6
0057-0SPR-SS4-M8
Washer Spring M8 S/S T304
2
A01
2 Point Backrest Mount - LEFT
29/06/2016
Mike Kearins
A3
SHEET
1 OF 2
DWG NO.
DESCRIPTION:
REVISION:
MATERIAL:
SIGNATURE
NAME
DEBURR AND BREAK SHARP EDGES
FINISH:
APPV'D
CHK'D
DRAWN
SCALE:1:2
DATE
mike.kearins - Wednesday, 29 June 2016 12:38:16 p.m. - C:\Medifab Vault\Products\New Spex\CAD\Backrest\
WEIGHT:
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
LINEAR TOLERANCES:
+
0.2mm
ANGULAR: TOLERANCES:
+
0.5°
g
32 Detroit Drive
iZone Business Hub
Rolleston 7675
New Zealand
Phone +64 3 307 9790
2
1
1
2
Backrest mounting hardware
PART NO.
ERP NO.
A-00531
ECN
CHANGE
FOR INTERNAL REVIEW ONLY
A-00531
C O N F I D E N T I A L
THIS INFORMATION IS HIGHLY CONFIDENTIAL AND IS THE
EXCLUSIVE PROPERTY OF MEDIFAB LIMITED.
THIS DRAWING MUST NOT BE USED FOR ANY PURPOSE
OTHER THAN THAT EXPRESSLY PERMITTED BY THE OWNERS
AND MUST BE RETURNED TO MEDIFAB LIMITED.
2
1X
6
2X
4
2X
3
2X
1
1X
5
2X
ITEM NO.
PART NUMBER
Description 1
QTY.
1
A-00112
2pt Mount Asy - Right
1
2
A-00113
2pt Inner Bracket - Right
1
3
0057-0FLT-SS-M8x16x1.2
Washer Flat M8 x 16 x 1.2 S/S
2
4
0054-NTND-M8SS
M8 Dome Nyloc Nut S/S 304
2
5
P-00406
M8 Square Neck Bolt
2
6
0057-0SPR-SS4-M8
Washer Spring M8 S/S T304
2
A01
2 Point Backrest Mount - RIGHT
29/06/2016
Mike Kearins
A3
SHEET
1 OF 2
DWG NO.
DESCRIPTION:
REVISION:
MATERIAL:
SIGNATURE
NAME
DEBURR AND BREAK SHARP EDGES
FINISH:
APPV'D
CHK'D
DRAWN
SCALE:1:2
DATE
mike.kearins - Wednesday, 29 June 2016 12:35:21 p.m. - C:\Medifab Vault\Products\New Spex\CAD\Backrest\
WEIGHT:
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
LINEAR TOLERANCES:
+
0.2mm
ANGULAR: TOLERANCES:
+
0.5°
g
32 Detroit Drive
iZone Business Hub
Rolleston 7675
New Zealand
Phone +64 3 307 9790
2
1
1
2
Backrest mounting hardware
PART NO.
ERP NO.
A-00532
ECN
CHANGE
FOR PROTOTYPE REVIEW
A-00532
DROITEGAUCHE
1 POINT 2 POINTS
2 POINTS