UVC Light Meter 850010 Instruction Manual Rev.
UVC Light Meter 850010 Copyright ©2009 by Sper Scientific ALL RIGHTS RESERVED Printed in the USA The contents of this manual may not be reproduced or transmitted in any form or by any means electronic, mechanical, or other means that do not yet exist or may be developed, including photocopying, recording, or any information storage and retrieval system without the express permission from Sper Scientific.
OPTIONAL ACCESSORIES 840090 Water Resistant Instrument Pouch 840092 Bench-Top Tripod 840093 Field Tripod - 22 - CONTENTS INTRODUCTION ............................... 4 FEATURES ....................................... 5 MATERIALS SUPPLIED………………. 6 LCD DISPLAY ................................... 7 BASIC FUNCTIONS .......................... 8 MODE AND UNIT SELECTION ........ 10 MEMORY .......................................... 14 UVC SENSOR…………………………. 17 BATTERY REPLACEMENT…………..
INTRODUCTION The Sper Scientific UVC Light Meter (Model 850010) is a light-weight, portable instrument that measures damaging UV (ultraviolet) light in both natural and manmade environments. The UV Light Meter measures short wave UV-C light for applications such as UV light fume hoods, UV sterilization, industrial glass and nondestructive testing. You can use the meter almost anywhere to determine UV light intensity and avoid the harmful effects of overexposure.
FEATURES MAINTENANCE 1. Dampen a sponge or soft cloth with soap and water to clean the housing. Tripod Mounting Socket High and low measurement range in milliwatts per square centimeter (mW/cm2) or microwatts per square centimeter (W/ cm2) Backlit LCD Magnetic Mount Simultaneous Display of Minimum, Maximum, Average and Recorded Data Zero Point Reset Hold Function 4 Digit Dual Display 20 Points Memory Automatic Measuring Low Battery Indicator 2.
MATERIALS SUPPLIED BATTERY REPLACEMENT Meter UV Probe Magnetic Mount 9 Volt Battery 1. Slide off battery cover from the back of the unit. Instruction Manual 2. Insert a 9V battery ensuring correct polarity. Hard Carrying Case 3. Replace battery cover. This unit requires one 9 Volt battery. The icon indicates a low battery.
UVC SENSOR LCD DISPLAY Portable Handheld Use 1. Upper casing x1 2. Sensor x1 3. Lower casing x1 4. Self-tapping screws x5 Note… To avoid wearing the screw holes, limit the number of times you assemble and disassemble the probe. - 18 - 1. Mode 8. MAX/MIN/AVG 2. Primary Reading 9. Secondary Reading 3. Data Log 10. Time Unit 4. Auto Mode 11. Unit of Measure 5. Memory Review 12. UV Type 6. Data Hold 13. Low Battery 7.
BASIC FUNCTIONS UVC SENSOR 1. Press and hold the HOLD button for 2 seconds to turn the meter on. All symbols on the LCD will appear for 1 second. 2. Press and hold the HOLD button for 2 seconds to turn the meter off. All symbols on the LCD will appear for 1 second. Release HOLD button. Reading the LCD Display 1. The primary display indicates measurement value. 2. The secondary display indicates the advanced functions or data recording.
MEMORY were automatically recorded, “AUTO” appears next to “MEM” during the recall. 4. As you scroll through data points 0 to 20, the saved minimum, maximum, or average value appears on the secondary display. BASIC FUNCTIONS Meter Function Flow Chart 1. Press MODE to choose the main function (MAX/MIN/AVG, Zero, Unit, Type or Time). MAX/MIN/AVG Mode is Normal Mode for this meter and has several sub-functions as indicated in the diagram below. 5.
MODE AND UNIT SELECTION MEMORY Mode Selection To Auto Record: 1. Press MODE continuously to cycle through MAX/MIN/AVG, Zero, Unit, Type, and Time Modes, respectively. 1. In Normal Mode, press and hold M for 2 seconds. “AUTO” appears next to “REC” on the LCD. As soon as the meter reaches 20 data points, the unit will turn off. Maximum, Minimum and Average (Normal Mode) 1. Press MODE continuously to cycle through modes until you reach MAX/MIN/AVG. 2.
MEMORY Manual Recording In Normal Mode, press M to store the current value that appears on the primary display. The flashing DATA(01~20) icon stops flashing for 2 seconds and moves to the next storage location. (Refer to Maximum, Minimum and Average/Normal Mode on pages 10-11 for instructions on saving max, min, and avg values.) Auto Recording To utilize auto recording, you must first set an interval time for recording measurement values.
MODE AND UNIT SELECTION Zero Adjustment 1. Press MODE continuously to cycle through modes until you reach Zero Mode. 2. Cover the sensor. If the main display has a reading other than zero, perform the zero adjustment. MODE AND UNIT SELECTION 5. In Zero Mode, press M to clear data points 0 to 20. Unit Selection 1. Press MODE continuously to cycle through modes until you reach Unit Mode. 2. Press S to choose the unit of measure: W/ cm2 or mW/cm2. 3. Cover the sensor and press S to zero adjust.
