Temperature Datalogger 800057 INTV 800057 3 Sec Erase MEMORY SELECT 1 Sec REC INSTRUCTION MANUAL Data Logger: 64,000 Records SPER SCIENTIFIC LTD.
CONTENT Page I. SAFETY INFORMATION --------------------- 2 II. FEATURES --------------------------------------- 2 III. GENERAL SPECIFICATIONS -------------- 3 IV. PANEL DESCRIPTION ----------------------- 4 V. OPERATION INSTRUCTIONS 5.1 Setup ----------------------------------------- 6 5.2 Record Temperature--------------------- 8 5.3 Erase Memory ----------------------------- 9 5.4 Download Memory ----------------------- 9 5.5 Battery Replacement ------------------ 10 VI. Software 6.
SPER 800057 I. SAFETY INFORMATION • Read the following safety information carefully before attempting to operate or service the meter. • Only qualified personnel should perform repairs or servicing not covered in this manual. • Periodically wipe the case with a dry cloth. Do not use abrasives or solvents on this instrument. • Safety symbols: Dangerous, refer to this manual before using the meter. Complies with European CE. II.
SPER 800057 III. GENERAL SPECIFICATIONS Measurement Range: -30°C ~ 70°C ; -22°F ~ 158°F Accuracy: ±0.7°C(± 1.3°F) Resolution: 0.1°C / 0.1°F Data Logger: 64,000 Records Storage Conditions: -30°C ~ 70°C Operating Conditions: -30°C ~ 70°C Response time: 20minutes to 95% under slow air. Battery: Size AAA 1.5V x 2 (alkaline battery) Battery Life: more than1 year (1 minute interval @ 25°C) Dimension: Recorder: 92 x 55 x 21mm Base: 107.5 x 62 x 28 mm Weight: Recorder: 95g Approx.; Base: 60g Approx.
SPER 800057 IV. PANEL DESCRIPTION 6 800057 1 1.
SPER 800057 Communication Status Record Interval Symbol Recording Symbol Battery Status Memory Status Display Temperature Unit Temperature Reading 1 RS-232 800056 2 3 PLEASE READ MANUAL FOR SAFET Y 1 RS-232 Jack ○ 2 Slip Proof Rubber ○ 3 Infrared RS232 Port ○ 5
SPER 800057 V. OPERATION INSTRUCTIONS 5.1 Setup Date And Time Setup: 1. Hold INTV SELECT buttons simultaneously for 3 seconds to enter date and time setup mode. 2. Press INTV to select year, month, day, hour and minute setup. 3. Press SELECT to set value on year, month, day, hour and minute. Note: Be sure to reset the data and time after replacing battery. The user can also setup the time through the PC software. There is a button in the software directly synchronize the setup to the PC.
SPER 800057 Setup Recording Interval and Temperature Unit: 1. Press and hold INTV for 2 seconds to record interval setup mode.(P-1) 2. Press SELECT to select recording interval. Options are 1,2,5,10,15,20,30 seconds and 1,2,5,10,20,30,60 minutes. 3. Press INTV to finish recording interval setup and go to temperature unit setup mode. (P-2) 4. Press SELECT 5. Press INTV to select °C or °F. to save and exit setup mode.
SPER 800057 5.2 Temperature Recording 800057 1. Press and hold SELECT for 1 second to start recording and LCD will display INTV “REC”. 2. To stop recording, press and hold SELECT for 1 second again. The “REC” symbol will disappear. 3. After step 1 and 2, it is called a data set stored in Recorder. 3 Sec Erase MEMORY ECT 1 Sec REC Note: 1. It is important to check the memory status before recording. 64,000 records available totally and each segment represents about 8,000 records available. 2.
SPER 800057 4. During temperature recording, recorder will turn on the LCD for 2 seconds and then go into power saving mode during each record interval. 5.3 Erase Memory 800057 1. Press and hold INTV simultaneously for 3 seconds to clear memory. 2. LCD will display “CLr”. TV 3 Sec Erase MEMORY 1 Sec REC SELECT Data Logger: 64,000 Records Memory display will resume in full status Note: You cannot erase the memory while temperature recording is active. 800056 5.4 Download Data 800057 1.
SPER 800057 3. Click “DataLogger” from SE-345 menu to download data. Note: 1. Refer to page 11(6.1) about installing SE-345 software. 2. Refer to page 12(6.2) about software introduction. 5.5 Battery Replacement 1. Please stop data recording before replacing battery. 2. Use two Alkaline Battery Size AAA 1.5V . 3. After replacing the battery, tighten these three screws securely.
SPER 800057 VI. Software 6.1 Installation • System Required: Windows 95/98/ME/NT 4.0. /2000/XP • Minimum Hardware Required: PC system with Pentium 233MHz or higher. 64 MB RAM. 4X CD-ROM Drive or higher. Recommended resolution 1024X768(or 800X600). At least 15 MB byte of free hard disk space available to install SE-345. • Installation : 1. Close all other applications before installing the TestLink SE-345 software. 2.
SPER 800057 6.2 Introduction • Main Screen Main menu Tool menu DataLogger window Data Set List Data List Graph Max/Min/Avg display • Main Menu File : Open - Open files saved previously from the disk. Save - Save the data to the disk. Print - Print the data (graph or list). Printer Setup - Select printer. Exit - Terminates program. DataLogger : By opening the DataLogger Window, the user can download recorded data from the meter to PC in this window. Setup: Setup Recorder from PC.
SPER 800057 View : Open LCD display window. Window : Arrange windows Help : On line help. • DataLogger Connect the Temperature Recorder to the PC. Start the SE345 software and select "DataLogger" from main menu or click from tool bar to load recorded data from the logger. There will be a progress indicator to show the download progress. If error occurs, just click "DataLogger" again.
SPER 800057 bar. Memory Status Erase Data Adjust Time Select Interval Select Unit Note: After you select interval or unit , you have to click the OK button to make this change valid. • Tutorial Quick Start (1) Recording real time data from PC. 1.Put the Temperature Recorder on the Communication Base, and connect it to a PC serial port with the SE-120 cable. 2.Run the SE345 Software. 3.If the connection is successful, the LCD will display the same value as the Temperature Recorder.
SPER 800057 (2) Save the recorded real time data to a file : 1. Select the window you want to save by clicking it, then choose File|Save from main menu or click * from the tool bar. 2. There will be a save dialog window for you to assign the file name and file type to save. 3.There are three types of file you can choose, they are binary file(*.ghf), text file(*.txt) and EXCEL format file(*.csv). The *.
SPER 800057 (3) Download the recorded data from the memory of Temperature Recorder and save it to a file: 1. Connect the Communication Base to PC 2. Put the Temperature Recorder on the Communication Base. 3. Start SE345 program. 4. Choose Data Logger from main menu or click from tool bar.
WARRANTY Sper Scientific warrants this product against defects in materials and workmanship for a period of five (5) years form the date of purchase, and agrees to repair or replace any defective unit without charge. If your model has since been discontinued, an equivalent Sper Scientific product will be substituted if available. This warranty does not cover probes, batteries, or damage resulting from accident, misuse, or abuse of the product.
