SPMLTT1000, SPMLTT2500, SPMLTG5000 SPEKTRUM LAP TIMING SYSTEM SPEKTRUM RUNDEN-TIMER SYSTÈME DE CHRONOMÉTRAGE DE TOURS SPEKTRUM SISTEMA DI CRONOMETRAGGIO SPEKTRUM 1
EN NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.
EN Spektrum Lap Timing SPMLTG5000 Gates and SPMLTT2500 Timing Receivers work with Spektrum™ Telemetry equipped radio systems, making it easy to set up a timing system without a personal computer. Compatible with Spektrum™ X-Bus and RPM Telemetry systems. Requires a Spektrum Telemetry capable transmitter and receiver system. For more information on Spektrum Telemetry visit: http://www.spektrumrc.com Contents Specifications ..............................................................................
EN Specifications Specifications SPMLTG5000 Type Dimensions (LxWxH) Weight IR source Input Voltage Compatibility Lap Timing System- Gate 51 x 31 x 16mm 14g 5 individual IR LEDs 3S LiPo (Balance Connector) SPMLTT1000, SPMLTT2500 Specifications SPMLTT2500 Type Dimensions (LxWxH) Weight Input Voltage Compatibility Lap Timing System- IR Receiver 23 x 23 x 12mm 5g 4–8.
EN Setting up the SPMLTG5000 Gate system The Infrared (IR) LEDs need to be strung up facing across the race track. The light beam from the IR LEDs is the virtual “gate” that will trigger the timing system when the SPMLTT2500 passes. IR LEDs may be attached to existing race gates, fence poles, or similar. Horizon Hobby racing gates FPV10604 and FPV10605 feature eyelets which can 5ft be utilized to hold the IR LEDs with a zip tie.
EN Track Setup Set up vertical timing gate(s) on an outside section of the track, facing outward across the track. Pointing the IR LEDs toward the center of the track may cause incorrect lap timing readings. Additional timing gates may be set up along the track at intervals to define lap segments. Up to 9 lap segments may be added in addition to the finish line gate. When first powered up, the 7 segment display will show your current voltage in single digits, starting with the first digit.
Low Voltage Cutoff for the SPMLTG5000 EN The SPMLTG5000 will go into a low voltage mode if the battery voltage drops below 10 volts. It will cease operation and begin alternating between “L” and “B” on the display to indicated low battery. Connecting the SPMLTT2500 There are two methods to connect the Lap Timing Receiver to Spektrum telemetry receivers. 1.
EN Connecting the SPMLTT1000 The Spektrum SPMFCF400 flight controller can be used directly with the SPMLTT1000 sensor. When the flight controller is paired with the SPM4649T reciever, the flight controller can send the lap timing information to the receiver with the standard 3-wire receiver connection without any additional wiring. Install the sensor from the top and solder the pins on the bottom of the flight controller.
EN Installing the SPMLTT2500 on a quadcopter Install the IR receiver with double-sided tape or adhesive-backed hook and loop material. The IR receiver must face the IR LEDs as the vehicle passes the timing gate. IMPORTANT: The IR receiver sensor must point toward the timing gate as it passes the gate. Do not mount the sensor pointed forward or backward.
EN Transmitter Setup Always use thee latest transmitter updates available at SpektrumRC SpektrumRC.com. co 1. Select the Lap Timer menu in the Function List. 2. Configure the timer mode and set the maximum number of laps. 3. In the Telemetry selection, choose LAP COUNTER if the sensor is connected to the X-Bus connection or flight controller, or RPM if the sensor is connected to an RPM input. IMPORTANT: Select RPM when using the SPM4649T telemetry receiver with the SPMLTT2500. 4.
EN Troubleshooting Guide Problem Missed Timing Possible Cause Gate battery low Obstruction to line of sight Power level too low Start/Finish gate not set to zero Telemetry not configured properly Sensor pointed directly at the sun Picking up timing when it shouldn’t Power level too high Timing gate pointed across track Sensor pointed directly at the sun Solution Charge battery Ensure clear line of site between gate and sensor Turn power level up Set Start/Finish gate as zero for gate number Ensure La
EN 1-YEAR LIMITED WARRANTY What this Warranty Covers - Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship for a period of 1 year from the date of purchase.
EN better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please visit our website at www. horizonhobby.com, submit a Product Support Inquiry, or call the toll free telephone number referenced in the Warranty and Service Contact Information section to speak with a Product Support representative.
EN Warranty and Service Contact Information Country of Purchase United States of America EU Horizon Hobby Contact Information Horizon Service Center (Repairs and Repair Requests) servicecenter.horizonhobby. com/RequestForm/ Horizon Product Support (Product Technical Assistance) productsupport@horizonhobby. com. Address 4105 Fieldstone Rd Champaign, Illinois, 61822 USA 877-504-0233 websales@horizonhobby.com Sales 800-338-4639 Horizon Technischer service@horizonhobby.
IT © 2017 Horizon Hobby, LLC. DSM is a registered trademark of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. All other trademarks, service marks and logos are property of their respective owners. Created 08/17 55702.
