SPMVT1000 Video Transmitter Manual

EN
3
1. Spektrum Serial Connector
2. Power Connector
3. A Button (POWER OUTPUT)
4. Channel LEDs (RED)
5. Band LEDs (BLUE)
6. Microphone
7. Antenna Connector
8. Power Level LEDs (GREEN)
9. B Button (CH, BAND)
10. Camera Connector
6
1
2
3
4
5
A
B
E
R
F
6
7
8
7
3
2
10
1
4 5
89
*200mW and 600mW power settings are only available for SPMVT1000. The
European version (SPMVT1000EU) is limited to 25mW.
Basic Operation
Mount the video transmitter in a secure location where it will be protected in the
event of a crash, with adequate air fl ow for cooling. See the frequency table below
to fi nd the desired video channel and band. The video transmitter channel, band and
power level are changed using the button on the video transmitter or the Spektrum™
VTX control system.
Channel and Band Selection:
1. A short press of the B button will change channels. Quickly press and release
the button once for each channel until the desired channel is reached.
2. A long press of the B button will change the band. Press and hold the B button for
several seconds and release for each band change.
Power Level Selection*:
1. Press and hold the A button to change the power output. All green LEDs off
means RF is off, one fl ashing green LED is Pit Mode, one solid green LED is
25mW, two solid green LEDs is 200mW, three solid green LEDs is 600mW.
Spektrum VTX Control:
1. Connect the Spektrum serial signal connector to the RC system.
2. Select the band, channel, and power output from the VTX menu on compatible
Spektrum Transmitters with Spektrum AirWare™ fi rmware.
Connecting An Antenna
The VT1000 video transmitter includes an SMA Antenna Adaptor which connects
to the main PCB with an MMXC connector.
1. Insert the MMCX connector into the video transmitter and ensure it is fully seated.
2. Mount the SMA connector through a hole in a mounting plate on the vehicle
and secure it with the lock washer and nut.
3. Install a compatible 5.8GHz antenna onto the SMA connector.
IMPORTANT: Do not kink or cut the antenna adaptor or antenna wires. Antenna wires
are coaxial wires, therefore kinks or cuts will degrade performance.
NOTICE: Powering on the video transmitter without an antenna connected will cause
damage to the video transmitter. Damage from powering on the video transmitter without
a compatible antenna attached is not covered under warranty.
Tip: The four mounting holes in the corners of the PCB work well with nylon
standoff set SPMVX180. For foam aircraft the threads can be inserted into the
foam and glued for secure mounting with excellent airfl ow.
BAND CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8
A Band A 5865 5845 5825 5805 5785 5765 5745 5725
B Band B 5733 5752 5771 5790 5809 5828 5847 5866
E Band E** 5705 5685 5665 5665 5885 5905 5905 5905
F FS/IRC 5740 5760 5780 5800 5820 5840 5860 5880
R RaceBand 5658 5695 5732 5769 5806 5843 5880 5917
BAND CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8
A Band A 5865 5845 5825 5805 5785 5765 5745 5745
B Band B 5733 5752 5771 5790 5809 5828 5847 5866
F FS/IRC 5740 5760 5780 5800 5820 5840 5860 5860
R RaceBand 5732 5732 5732 5769 5806 5843 5843 5843
EU Frequency Chart
†
North American Frequency Chart
†
Frequency sets have been limited to prevent transmitting outside of designated CE Frequencies.