RAPTOR ® VISOR LIGHT BAR B-RTC12 B-RLC12 INSTRUCTION MANUAL 1 SpeedTech Lights, Inc © 2019
RAPTOR ® VISOR LIGHT BAR Warnings and Notices for Users and Installers This document must be delivered to and read by the end user and installer as it serves to provide you with the required information for proper and safe use of your STL product. Before operating this or any STL products the user and installer must read this manual all the way through. You will find important information in this manual that could prevent property damage and/or serious injury to the user and installer.
RAPTOR ® VISOR LIGHT BAR Important Points for Your Safety and Longevity of Your Light Bar • • • • • • • • • • • • • • • Installers are required to have a good understanding of automotive electronic systems and procedures for proper installation. Never stare directly into the LEDs as momentary blindness and/or eye damage may occur. Never take any lights through a car wash. Use only water to clean the outer body/lens of your equipment. Never use a pressure washer to clean any STL products.
RAPTOR ® VISOR LIGHT BAR Wiring Diagram Wire Color Function Wire Color Function Red* Positive White Positive (When bypassing Grand Control Box) Black* Negative Blue Take Down Steady Yellow Flash Pattern Green Take Down Flashing NOTE: All cables except Negative contact +12 VDC. * Indicates a main power cable. AUX Wiring Diagram Wire Color Function Red AUX Positive Blue AUX Negative Specifications Voltage 12 VDC Amps < 4.
RAPTOR ® VISOR LIGHT BAR Available Visor Bracket Mounts 5 SpeedTech Lights, Inc © 2019
RAPTOR ® VISOR LIGHT BAR Raptor Mounting Bracket Contents Inspect contents of package. Universal Brackets: • (4) Base brackets • (4) Universal forked visor brackets Universal Bracket Hardware Contents: • (20) Philips pan head screws • (30) Flat washers • (20) Split lock washers • (12) Hex nuts • (2) Rubber protective strips Bracket Spacer Contents: • (8) 5.
RAPTOR ® VISOR LIGHT BAR Raptor Mounting Bracket Installation Base Bracket and Universal Visor Bracket Assembly To attach the base bracket and visor bracket, you will need the following for each of the 4 assemblies: • (2) Phillips pan head screws • (4) Flat washers • (2) Split lock washers • (2) Hex nuts 1. Take both brackets and overlap the openings. Visor Bracket Base Bracket 2. Insert (2) Phillips pan head screws through the base bracket opening. 3.
RAPTOR ® VISOR LIGHT BAR Attaching Assembly to Raptor Light Bar Base There are 4 holes on the bottom of each Raptor segment (8 holes total). NOTE: Only 1 hole will be used for each assembly. Choose the hole that will allow best fitment to the vehicle. 1. Attach each assembly using the appropriate selected mounting hole, via the base bracket, using (1) Phillips pan head screw. Hand tighten only at this point. 2.
RAPTOR ® VISOR LIGHT BAR Base Bracket and Vehicle Specific Visor Bracket Assembly NOTE: This assembly is very similar to the Universal Bracket assembly. The only difference is the Vehicle Specific visor brackets will be used instead of the Universal forked visor brackets to pair with the base brackets. For this example, the 2015+ Dodge Ram Vehicle Specific Brackets (Q-303) will be used. NOTE: Hardware quantity used will vary based on single or double mounting holes. 1.
RAPTOR ® VISOR LIGHT BAR Spacer Installation NOTE: Spacers are included to assist in adjusting the Visor Light Bar to the windshield. 1. Take both brackets and overlap the openings. 2. Insert (2) Phillips pan head screws through the base bracket opening. 3. Select necessary size spacer and place spacer onto each screw between the brackets. 4. On the other end, insert (2) flat washers, (2) split lock washers, and (2) hex nuts to secure.
RAPTOR ® VISOR LIGHT BAR Flash Pattern List • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Steady Burn Steady Burn Left Side. Quad Flash Right Side 120 FPM Steady Burn Right Side.