Metered Commercial Original Instructions Keep These Instructions for Future Reference. CAUTION: Read the instructions before using the machine. (If this machine changes ownership, this manual must accompany machine.) www.alliancelaundry.com Installation/Operation Topload Washers TLW12C_SVG Part No.
WARNING Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 WARNING For your safety and to reduce the risk of fire or an explosion, do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
Table of Contents Safety Information..................................................................................6 Explanation of Safety Messages....................................................................... 6 Important Safety Instructions........................................................................... 6 Dimensions............................................................................................. 8 Installation..............................................................
Start Washer..............................................................................................20 Indicator Lights.........................................................................................20 Maintenance......................................................................................... 21 User-Maintenance Instructions....................................................................... 21 Cold Weather Care.....................................................................
Safety Information Safety Information Explanation of Safety Messages Important Safety Instructions Precautionary statements (“DANGER,” “WARNING,” and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining the machine.
Safety Information • • • • • • • • • • • • • Children less than three years should be kept away unless continuously supervised. Do not reach into the washer if the washtub or agitator, if applicable, is moving. Never operate the washer with any guards, panels and/or parts removed or broken. DO NOT tamper with the controls or bypass any safety devices. Use your washer only for its intended purpose, washing clothes. Always follow the fabric care instructions supplied by the garment manufacturer.
Dimensions Dimensions A 1 C B H I J L K D C H G F E TLW2208N_SVG 1. Pilot Hole A 22.44 in. [570 mm] B 51 in. [1295 mm] C - Standard Capacity Meter Case 43 in. [1092 mm] C - High Capacity Meter Case 43.875 in. [1114 mm] D 38.19 in. [970 mm] E 28 in. [711 mm] F 26 in. [660 mm] G 0.44 in. [11 mm] H 36 in. [914 mm] I 41.25 in. [1048 mm] J 28.75 in. [730 mm] K 25.63 in. [651 mm] L 30.5 in.
Installation Installation Before You Start 2. 3. 4. 5. 6. 7. 8. 9. Tools For most installations, the basic tools you will need are: 2 1 Wipe out inside of the washer. Connect the fill hoses. Connect the drain hose to the drain receptacle. Position and level the washer. Plug in the washer. Add water to the washer. Check the lid switch. Check installation. Remove the Shipping Brace and Shipping Plug 3 4 1. Remove the shipping brace from under the lid. 2.
Installation 1 3 2 TLW2099N_SVG Figure 3 TLW2098N_svg Connect Fill Hoses 1. Shipping Brace 2. Shipping Plug 3. Cardboard Base WARNING Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period and before using the washer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas.
Installation 8. Continue tightening and rechecking until no leaks are found. Water Supply Requirements Water supply faucets must fit standard 3/4 inch [19 mm] female garden hose couplings. DO NOT USE SLIP-ON OR CLAMPON CONNECTIONS. COLD HOT NOTE: Water supply faucets should be readily accessible to permit turning them off when washer is not being used. 4 1 2 3 C H 8 Recommended cold water temperature is 50° to 75° Fahrenheit [10° to 24° Celsius].
Installation 1 1 3 2 2 1. Drain Hose 2. Standpipe 3. Recommended Standpipe Height 36 in. [914 mm] Minimum W005I_SVG 1. Risers (Air cushions) 2. Water Supply Faucets Figure 6 Figure 5 Connect Drain Hose to Drain Receptacle IMPORTANT: The drain hose installation is a very important factor in the washer installation. If care is not taken when the drain hose is installed, a siphoning action can be started which will cause water to be siphoned from the washer during the cycle.
Installation 1 1 2 2 5 4 { 4 3 3 TLW2210N_SVG 1. Drain Hose 2. Cut Drain Hose off at This End to Fit the Washer Installation 3. Standpipe 4. Maximum Standpipe Height Not To Exceed 5 ft. [1.5 m] Low Standpipe Installation If the drain facility is lower than the cabinet top, a siphon break kit, Part No. 562P3, must be installed in the drain hose to prevent siphoning action and drain hose MUST be cut to fit the washer installation. Refer to Figure 8 . Use one No. 25863 Hose Coupling to splice hose.
Installation NOTE: For areas with uneven floors, a No. 566P3 Adjustable Rear Leg Extension Kit is available as optional equipment at extra cost. 8. Verify that unit does not rock. • • • The washer is designed to be operated on a separate branch, polarized, three-wire, effective earth/ground, 120 Volt, 60 Hertz, AC (alternating current), circuit protected by a 15 ampere fuse, equivalent fusetron or circuit breaker.
Installation Add Water to the Washer WARNING To reduce the risk of an electric shock or fire, DO NOT use an extension cord or an adapter to connect the washer to the electric power source. W082 Earth/Ground Instructions This appliance must be properly connected to protective earth/ ground. In the event of malfunction or breakdown, the earth/ ground will reduce the risk of electric shock by providing a path of least resistance for electric current.
Installation 2. Run washer through one complete cycle to make sure it is operating properly. Vending Meter Case The factory mounted coin meter case does not include the service door lock, coin slide (if applicable), coin drawer, coin drawer lock or keys. These parts must be ordered (at extra cost) according to the purchaser’s requirements direct from the manufacturer of your choice. NOTE: You have the option of using a screw type lock or a 1/4 turn lock on the meter case service door.
Installation 7. Remove two screws holding front panel to base of washer and install two No. 12 tamper-resistant screws, Part No. 35527. 1 2 3 TLW2102N_SVG 1. 35528 No. 8 Screws 2. Double “D” Hole 3. 35527 No. 12 Screws Figure 14 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 17 Part No.
Operation Operation Operation Instructions IMPORTANT: Prior to first wash, use an all-purpose cleaner, or a detergent and water solution, and a damp cloth to remove shipping dust from inside of washer. IMPORTANT: Remove all sharp objects from laundry to avoid tears and rips to items during normal machine operation. Add Detergent 1. Pour measured amount of detergent into washtub. Refer to package directions. 2. NEVER POUR UNDILUTED BLEACH DIRECTLY ON LAUNDRY. Follow package directions when using bleach.
Operation Set Cycle Select Soil Level Push Cycle touchpad for NORMAL, PERM PRESS or DELICATES. Light indicates selection. Push Soil touchpad for LIGHT, MEDIUM or HEAVY. Light indicates selection. NOTE: The NORMAL cycle is recommended for everyday cottons and linens. NOTE: The LIGHT soil level is recommended for everyday cottons and linens. Soil LIGHT MEDIUM Cycle NORMAL PERM PRESS Temp HOT Fabric softener should only be used when the Heavy soil level is selected.
Operation Insert Coins or Card Start Washer To Insert Coins After vend price has been satisfied, push the start pad. LID MUST BE CLOSED TO START WASHER. 1. Insert coin(s) in coin slot. 2. Check pricing as seen on digital display. Soil LIGHT MEDIUM Cycle NORMAL PERM PRESS Temp HOT HEAVY DELICATES WARM COLD START TLW2277N_SVG Figure 23 Indicator Lights W387I_SVG INSERT COINS/CARD INSERT COINS/CARD is lit to prompt the user to insert coins or a card to satisfy the vend price.
Maintenance Maintenance User-Maintenance Instructions Shipping Brace Cold Weather Care The shipping brace in the lid opening should be saved and reinstalled whenever the washer is moved. To reinstall the brace, open the washer lid and place the brace over the washer agitator, placing the back of the brace into the lid opening first.
Troubleshooting Troubleshooting Try these troubleshooting tips before making a service call. They may save you time and money. Washer Symptom Won’t Fill Possible Cause/Solution • • • • • • • • • • • • Make sure lid is closed. Make sure power cord is plugged all the way into the electrical outlet. Check the laundry room fuse or circuit breaker. Insert coin(s) or card. Make sure that the controls are properly set. Make sure hot and cold water faucets are turned on.
Troubleshooting Washer Symptom Won’t Spin Possible Cause/Solution • • • • • • • Stops/Pauses During Cycle • • • Make sure lid is closed. Make sure power cord is plugged all the way into the electrical outlet. Check the laundry room fuse or circuit breaker. Insert coin(s) or card. The motor overload protector may have stopped the cycle. It will reset itself in two or three minutes and restart the washer automatically. Broken drive belt. Call the service person.
Contact Information Contact Information If service is required, contact the nearest Factory Authorized Service Center. Model Number If you are unable to locate an authorized service center or are unsatisfied with the service performed on your unit, contact: Alliance Laundry Systems Shepard Street P.O. Box 990 Ripon, WI 54971-0990 U.S.A. www.alliancelaundry.com Phone: +1 (920) 748-3121 Serial Number Please include a copy of your bill of sale and any service receipts you have.
Installer Checklist Installer Checklist Fast Track for Installing the Washer 1 Remove the Shipping Brace and Shipping Plug. 5 CHECK Position and Level the Washer. CHECK TLW2098N_SVG1 TLW2201N_SVG 2 Wipe Out Inside of Washer. 6 CHECK Plug In the Washer. CHECK TLW2099N_SVG D254I_SVG 3 Connect Fill Hoses. 7 Add Water to the Washer. COLD CHECK HOT CHECK TLW2056N_SVG TLW1988N_SVG 4 Connect Drain Hose to Drain Receptacle. 8 CHECK Check Lid Switch.
