Installation Instructions

Vending
Coin Slide Guards
Using sheet metal screws from accessories bag (located in lower
cylinder), install coin slide guards (located in accessories bag in
lower cylinder) to front of dryer’s control cabinet. Refer to Fig-
ure 34 .
PUSH TO START
IN USE
IN USE
PUSH TO START
FABRIC SELECTOR
FABRIC SELECTOR
PERM PRESS
NORMAL
DELICATE
FLUFF
(NO HEAT)
PERM PRESS
NORMAL
DELICATE
FLUFF
(NO HEAT)
D784I_SVG
1
1
2
2
1. Coin Slide Guard
2. Sheet Metal Screws
Figure 34
NOTE: Coin slides and coin drawers are shown for il-
lustration only. You must obtain them locally.
Coin Slide Control
Power-Up Mode
Shortly after power is applied to the dryer, the control will flash
once to indicate the machine is ready to be used. If a cycle was
running previously, the control will blink and then stay lit, indi-
cating there is still time remaining from the previous cycle. If the
control was not previously running a cycle, the control will be in
Ready Mode.
Ready Mode
In Ready Mode, the control waits for the vend to be satisfied be-
fore entering Start Mode.
Start Mode
In Start Mode, the vend has been satisfied, but the Start button
has not been pressed. The IN USE LED will be lit. The timer will
not count down until the Start button is pressed.
Run Mode
In Run Mode, the control is running a cycle. The IN USE LED is
lit.
Door Open Mode
In Door Open Mode, the control turns off the heater and motor
when the door is opened during a run cycle. The timer will con-
tinue to count down time and the IN USE LED is lit.
End of Cycle Mode
In End of Cycle Mode, a cycle is complete and the IN USE LED
is off. The control remains in this mode until the door is opened
or additional vend has been satisfied.
Top-Offs
Any time the control receives a coin slide pulse during a cycle it
will add the programmed dry time to the time currently remaining
in the cycle. The IN USE LED will flash briefly to indicate the
coin input. The maximum cycle time is 99 minutes. The control
will not add time beyond 99 minutes. The cool down time will
not change. If the control receives a coin slide pulse during cool
down it will exit cool down and start heating with the cycle time
equal to the programmed time.
Temperature Selector Switch
Drying temperature is selected using the Temperature Selector
Switch. Temperature options for cycles are NO HEAT
, LOW,
MEDIUM and HIGH.
Error Display Mode
The control enters Error Display Mode to display thermistor er-
rors. The heater is turned off, the IN USE LED flashes to indicate
the error (refer to paragraphs below), and the timer will continue
to count down time. The control remains in Error Display Mode
until the control senses the thermistor has returned to an accepta-
ble heating range, the cycle ends or machine is powered down.
Open Thermistor
If the control senses a temperature less than 0°F when the heat
has been on for at least three minutes it will set an open thermis-
tor error. The control will flash the IN USE LED twice separated
by a one and a half second pause. This sequence is repeated as
long as the Open Thermistor error is sensed.
Shorted Thermistor
If the control senses a temperature greater than 210 ± 4°F during
an active cycle it will set a Shorted Thermistor error. The control
will flash the IN USE LED three times separated by a one and a
half second pause. This sequence is repeated as long as the Short-
ed Thermistor error is sensed.
Setting Dry Time Dipswitches
There are two banks of dipswitches on the dryer control: Dips-
witch1 and Dipswitch2. Each bank has eight switches: Dips-
witch1, Switch 1-8 and Dipswitch2, Switch 1-8. Bank Dips-
witch1 configures machine definition. Bank Dipswitch2 config-
ures vended cycle definition. Refer to Table 7 and Table 8 for
dipswitch options.
Vending
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
32
Part No. D516906ENR1