Washer Owner's Manual

Choose Light, Medium, Heavy or Max according to the amount
of soil in the laundry load. Light is the minimum and Max is
the maximum amount of time.
The Soil Level LED will flash to indicate that you can also ad-
just the Wash Time using the up and down arrow keypads. The
time is increased or decreased by one minute.
Options
The following options can be used to modify the currently
chosen cycle, signal volume and control lock.
Soak
The Soak option is added to the beginning of the cycle. Use for
heavily soiled or stained clothing. The washtub will fill with wa-
ter, agitate for a reduced period of time, and pause for the set
amount of time.
The Soak LED will flash to indicate that you can set the
amount of soak time by pressing the Soak keypad again or the
up and down arrow keypads. The time will increase by 15 mi-
nutes up to an hour and then go up by one hour increments.
The maximum soak time is 24 hours.
The soak LED also will flash during any soak portion of the cy-
cle.
Pre-Wash
The Pre-Wash option adds a second wash to the selected cy-
cle.
Extra Rinse
This Option will provide an additional rinse to the selected cy-
cle. The water temperature will be cold.
Allergy Rinse
The Allergy Rinse Option provides two additional rinses. It is
useful for detergent sensitive skin. The water temperature will
be cold.
NOTE: If Extra Rinse and Allergy Rinse are both selec-
ted, the cycle will provide a total of three additional rin-
ses.
Delay Start
Pressing the Delay Start Option will allow the cycle to begin up
to 24 hours later. Pressing it once will delay the cycle by one
hour and 1h will display on the control. Press the Delay Start
keypad again or the up arrow keypad. The time will increase by
one hour. Press the Start/Pause keypad to begin the count-
down.
While setting the Delay Start Option, the cycle time and the
Delay Start keypad light will flash (1 second on/off).
After the Delay Start Option is started, the Delay Start keypad
light will flash (1 second on/off).
Signal
Pressing the Signal keypad will change the end of cycle signal
volume. There are four settings: Off, Low, Medium, High.
Control Lock (Secure keypad)
Pressing and holding the Signal keypad for three seconds will
turn on the Control Lock. The Control Lock status light will be
lit. While Control Lock is on, no other keypad presses are al-
lowed. Press and hold the Signal keypad again to turn the op-
tion off.
Status
The Status lights are lit during the cycle to show what part of
the cycle is running.
Wash The Wash status light is lit during the
wash portion of the cycle including Pre-
Wash and Soak, if selected.
Rinse The Rinse status light is lit during the
rinse portions of the cycle including Sec-
ond Rinse and Third Rinse, if selected.
Spin The Spin status light is lit during the final
spin portion of the cycle.
Door Lock The Door Lock status light is lit whenever
the door is locked. The door cannot be
opened while it is lit.
While the door is locking, the door lock status light flashes (1
second on/1 second off). While unlocking, the door lock status
light stays lit and the cycle time flashes (1 second on/1 sec-
ond off).
To Wash Clothes
IMPORTANT: Before using your new washer, make
sure the washer cord is connected to an appropriate
electrical outlet that is properly installed and connec-
ted to a protective earth/ground. Make sure the washer
hoses are connected to the hot and cold water faucets,
and that the faucets are turned on. Be sure the drain
hose is not kinked and is inserted into a drain. Refer to
the INSTALLATION INSTRUCTIONS for details of prop-
er washer installation.
IMPORTANT: Prior to first wash, use an all purpose
cleaner, or a detergent and water solution, and a damp
cloth to remove shipping dust from inside of wash
drum.
1. Get the clothes ready for washing. Empty pockets and
cuffs. Sort items into separate loads. Pretreat stains and
heavily soiled areas.
Control Panel
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
13 Part No. 807493ENR1