Installation Instructions for Frontload Washers Original Instructions Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) www.speedqueen.com Part No.
Table of Contents Washer Dimensions................................................................................ 4 Installation............................................................................................. 5 Before You Start.............................................................................................5 Tools............................................................................................................. 5 Parts Included............................................
Washer Dimensions Washer Dimensions B A C D F E G L J H I K FLW2298N_SVG Figure 1 A 24.06 in. [611 mm] B 23.19 in. [589 mm] C 40.77 in. [1036 mm] D 43 in. [1092 mm] E 32 in. [813 mm] F 36 in. [914 mm] G 14.6 in. [371 mm] H 26.875 in. [683 mm] I 2.04 in. [52 mm] J 27.73 in. [704 mm] K 1.59 in. [40 mm] L 13.1 in. [333 mm] Part No.
Installation Installation Before You Start Tools For most installations, the basic tools you will need are: 1 • • • • • • Two fill hoses with washers and filter screens Four rubber feet Beaded strap Installation Instructions User’s Guide Warranty Bond 2 Order of Installation Steps 4 The proper order of steps must be followed to ensure correct installation. Refer to the list below when installing your unit. 3 5 " 16 9/ 6 7 8 FLW2376N_SVG 1. 2. 3. 4. 5. 6. 7. 8.
Installation 2. Remove two 9/16 inch bolts and washers holding shipping brace to weight. 3. Remove two 9/16 inch bolts and washers holding shipping brace to washer base and remove brace. IMPORTANT: Do not lift or transport unit from front or without shipping materials installed. Refer to the User’s Guide for proper instructions on reinstalling the shipping materials. Connect Fill Hoses WARNING 1 FLW2296N_SVG Figure 4 4. Go to rear of washer and pull label from rear shipping bolts. 5.
Installation Turn on the water supply faucets and flush the lines for approximately two minutes to remove any foreign materials that could clog the screens in the water mixing valve. This is especially important when installing your washer in a newly constructed or renovated building. Build-up may have occurred during construction. Connecting Hoses 1. Remove the two plain rubber washers and two filter screens from the accessories bag. 2. Install them into each end of the fill hoses as shown in Figure 7 .
Installation 1 1 3 2 2 FLW2301N_SVG 1. 24 to 36 in. [610 to 914 mm] Recommended Height 2. Beaded strap from accessory bag 3. Standpipe 2 in. [51 mm] or 1-1/2 in. [40 mm] FLW2302N_SVG 1. Drain Hose 2. Beaded Strap (tape if necessary) Figure 10 Figure 8 Position and Level the Washer Wall Installation For installations of this type, the drain hose MUST be secured to one of the fill hoses using the beaded strap from accessories bag. Refer to Figure 9 .
Installation NOTE: DO NOT slide unit across floor if the leveling legs have been extended. Legs and base could become damaged. 7. Remove rubber feet from accessories bag and place on all four leveling legs. 8. Verify that unit doesn’t rock. To reduce the risk of fire, electric shock, serious injury or death, all wiring and protective earth/ground connections MUST conform with the latest edition of the National Electrical Code, ANSI/NFPA No. 70, and such local regulations as might apply.
Installation WARNING 2 3 1 8 Improper connection of the equipment earth/ground conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the washer is properly connected to a protective earth/ground. 6 7 W822 4 5 • • DRY2022N_SVG Standard 120 Volt, 60 Hertz 3-Wire Effective Earth/Ground Circuit 1. L1 2. Earth/Ground 3. Neutral Side 4. Round Earth/Ground Prong 5. Neutral 6. 0 V.A.C. 7. 120 ± 12 V.A.C. 8. 120 ± 12 V.A.
Installer Checklist Installer Checklist Fast Track for Installing the Washer 1 Position Washer Near Installation Area. 5 CHECK Position and Level the Washer. CHECK FLW2299N_SVG1 2 Remove the Shipping Materials and Install Plugs. 6 CHECK Wipe Out Inside of Washer. CHECK FLW2303N_SVG FLW2359N_SVG 3 Connect Fill Hoses. 7 COLD Plug In the Washer. HOT CHECK CHECK FLW2304N_SVG D254I_SVG 4 Connect Drain Hose to Drain Receptacle.
