22 TON VERTICAL/HORIZONTAL LOG SPLITTER MODEL NO. S401622PH Owner’s Manual ASSEMBLY & OPERATING INSTRUCTIONS WARNING: All operators must read this manual before operating this log splitter. Follow the safety instructions in the manual and in decals attached to the product. Failure to do so could result in serious injury or death. LS147-832-0312 Rev.
Table of Contents Important Safety Information................................................................................................................. Page(s) 1-6 Intended Use ......................................................................................................................... 1 Personal Protective Equipment ............................................................................................... 1 Safety Decals .............................
WARNING: Read and thoroughly understand all instructions in this manual and on safety decals before assembling or operating this log splitter. Failure to do so may cause serious injury or death. Do not allow anyone to operate this log splitter who has not read this manual. As with all power equipment, a log splitter can be dangerous if assembled or used improperly. Do not operate this log splitter if you have any questions concerning safe operation.
PART NUMBER: S52062200 LOCATION: TOP OF CYLINDER PART NUMBER: S52062300 LOCATION: STRIPPER PLATE, OPERATOR SIDE PART NUMBER: S52062600 LOCATION: STRIPPER PLATE, NON OPERATOR SIDE PART NUMBER: S52062400 LOCATION: HYDRAULIC TANK LOWER TANK, RIGHT CORNER PART NUMBER: S52062100 LOCATION: TOP OF HYDRAULIC CYLINDER Page 2
GENERAL SAFETY ALWAYS keep the operator’s manual nearby for reference. Reread the manual periodically. ALWAYS keep all bystanders and pets a minimum of 10 feet away from your work area when operating this log splitter. Only the operator is to be near the log splitter during use. NEVER allow adults lacking proper instructions and understanding to operate this log splitter. NEVER actuate the control until all people are clear of the work area.
ALWAYS block the wheels to prevent movement of the log splitter while in operation. KNOW how to stop the log splitter and disengage the controls before operating it. NEVER place hands or feet between the log and splitting wedge during forward or reverse stroke as this could result in serious injury or death. NEVER straddle or step over the log splitter during operation. NEVER reach or bend over the log splitter to pick up a log. NEVER try to split two logs on top of each other.
MAINTENANCE & SAFETY The hydraulic system of your log splitter requires careful inspection along with the mechanical parts. Be sure to replace frayed, kinked, cracked or otherwise damaged hydraulic hoses or hydraulic components. NEVER check for leaks of hydraulic fluid with your hand. Fluid escaping from a small hole can be almost invisible. Escaping fluid under pressure can have sufficient force to penetrate skin causing SERIOUS INJURY or even DEATH.
IMPORTANT NOTE – (spark arrester): As a precautionary measure against possible flying sparks, always take a Class B fire extinguisher with you when operating this log splitter in dry areas. This log splitter is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).
ASSEMBLY INSTRUCTIONS NOTE: This log splitter was partially assembled at the factory. Refer to the drawings and parts list should it become necessary to disassemble the unit for repair or replacement of parts 5 ITEM NO. DESCRIPTION QTY. 1 2 3 4 5 Beam Assembly Beam Lock Assembly Tank Assembly Tire and Wheel Tongue Assembly 1 1 1 2 1 STEP 1: Remove all the components from the shipping container. Inspect each piece for shipping damage.
STEP 3: Attach the tongue assembly (5) to the tank assembly (1) using two 1/2” NC x 4-1/2” hex cap bolts (2), two 1/2” lock washers (3) and two and two 1/2” hex nuts (4). Tighten. ITEM NO. 1 2 3 4 5 DESCRIPTION Tank Assembly 1/2” NC x 4-1/2 Hex Bolt 1/2” Lock Washer 1/2” NC Hex Nut Tongue Assembly QTY. 1 2 2 2 1 STEP 4: Stand the beam (1) up on end. Two people may be needed for this step to ensure safety. Make sure that the beam is stable and on a level surface.
STEP 5: Connect the end of the 1/2” ID x 38” hydraulic pressure hose (1) coming from the fitting on the pump to the fitting on the valve. See illustrations below. STEP 6: Slide one hose clamp on the end of the 3/4” x 56” hydraulic return hose (2) that comes from the fitting on the filter. Then connect the hose to the fitting on the valve. Tighten hose clamp. See illustrations below. DETAIL A SCALE 1:3 Area of Detail ITEM NO. DESCRIPTION QTY.
REPLACEMENT PARTS TANK/ENGINE ASSEMBLY BREAKDOWN ITEM NO. PART NO. DESCRIPTION QTY. 1 O/L 5/16” Flat Washer 8 2 O/L 5/16”-18 UNC Nylock Nut 4 3 O/L 5/16” x 1-1/2” GR 5 Bolt 4 4 S40118800 Tank 1 5 S390604B0 25 PSI Filter Base 1 5A S3920601A0 Filter Element 1 6 S39049000 Hex Nipple 1 7 S39038300 Straight Fitting, 3/4” NPT 1 to 3/4” ID Tube 8 S39032000 3/4” NPT x 3/4” Tube 1 9 S39073100 Pump/Honda GC190 Assy.
BEAM ASSEMBLY BREAKDOWN ITEM NO. PART NO. 1 O/L 2 O/L 3 O/L 4 S401414R0 5 S40141700 6 S390118BC 7 S07073100 8 S390406SC 9 SS39034700 10 S39034300 11 S39032000 12 S39039000 13 S39034600 S40127500 S39044400 DESCRIPTION QTY.
OPERATING INSTRUCTIONS WARNING: Read and thoroughly understand all instructions and safety information before operating this log splitter. Failure to do so may cause serious injury or death. Do not allow anyone to operate this log splitter who has not read this manual. As with all power equipment, a log splitter can be dangerous if assembled or used improperly. Do not operate this log splitter if you have doubts or questions concerning safe operation.
NOTE: The engine maximum governed speed is preset at the factory at 3600 RPM no load speed. When splitting wood the throttle should be set at the maximum speed to develop the horsepower required for the pump. OPERATION WARNING: See safety information related to operation of the log splitter on page 3 and 4 of this manual. Make sure that you have the recommended personal protective equipment described on page 1. 1) Set up the log splitter in a clear, level area and block the wheels.
IMPORTANT NOTICE We, the manufacturer, reserve the right to change the product and/or specifications in this manual without notification. The manual is for information usage only and the pictures and drawings depicted herein are for reference only. NOTES Warranty Repair and Service Do not return this product to the store for warranty issues or repair. Call 1-800-525-8322 for the location of the nearest service center. Record the information below for future reference.
SPECIFICATIONS MODEL NO. S401622PH MAXIMUM SPLITTING FORCE* ENGINE CYLINDER 22 Tons Honda GC 190 Engine 4” Diameter X 24” Stroke VALVE Auto-Return PUMP Two-Stage 11 gpm MAXIMUM LOG LENGTH CYCLE TIME * 26” 13 Seconds WHEELS 4.80 X 8” Pneumatic Tires on Rims WEDGE 7” High with Spreader Wings BEAM SIZE 6” X 9” TOTAL HYDRAULIC CAPACITY 6.5 Gallons Maximum FILTER Spin-On Replaceable HEIGHT 72” in Vertical Position 42” in Horizontal Position LENGTH 78” WIDTH 45” SHIPPING WEIGHT 550 lbs.
