5 TON ELECTRIC LOG SPLITTER MODEL NO. 40100500 Owner’s Manual ASSEMBLY & OPERATING INSTRUCTIONS This safety alert symbol identifies important safety messages in this manual. Failure to follow this important safety information may result in serious injury or death. LS102-778-0608 Rev.
Table of Contents Page(s) Important Safety Information................................................................................................................. 1-6 Intended Use ......................................................................................................................... 1 Personal Protective Equipment ............................................................................................... 1 General Safety ..........................................................
WARNING: Read and thoroughly understand all instructions and safety information before assembling or operating this log splitter. Failure to do so may cause serious injury or death. Do not allow anyone to operate this log splitter who has not read this manual. As with all power equipment, a log splitter can be dangerous if assembled or used improperly. Do not operate this log splitter if you have doubts or questions concerning safe operation.
SAFETY DECALS Make sure that all safety warning decals are in good condition and readable. Always replace missing or defaced decals. Write us or call 1-800-525-8322 and they will be sent to you at no charge. LOCATION: SIDE OF BEAM, WEDGE END PART NUMBER: 52036900 Read and understand manual before assembly and operation. Page 2 Keep all people and pets away from work area. Only the operator should be near the log splitter during operation. Always wear protective gloves.
PREPARATION OF THE LOG Both ends of the log should be cut as square as possible to help prevent the log from riding out of the splitter during ER operation. Do not split logs greater than 20 in. in length. WORK AREA NEVER operate the log splitter on slippery, wet, muddy or icy ground. ONLY operate your log splitter on a level surface. Operating on a slope could cause the log splitter to roll over or logs to fall off.
REPAIR AND MAINTENANCE SAFETY NEVER operate your log splitter when it is in poor mechanical condition or in need of repair. ALWAYS unplug the power cable before performing any maintenance and repair. Periodically check that all nuts, bolts, screws, hydraulic fittings and hose clamps are tightened. NEVER alter your log splitter in any manner such as adding a rope or extenstion to the control lever or adding to the width or height of the wedge.
FIRE PREVENTION NEVER operate your log splitter near a flame or spark. Hydraulic oil is flammable and can explode. ALWAYS take a Class B fire extinguisher with you when operating this log splitter in dry areas as a precautionary measure against possible flying sparks. TRANSPORTATION NEVER move this log splitter while the motor is running. NEVER carry any cargo or wood on your log splitter. NEVER allow anyone to sit or ride on your log splitter.
ASSEMBLY INSTRUCTIONS NOTE: This log splitter was partially assembled at the factory. Refer to the drawing and parts list should it become necessary to disassemble the unit for repair or replacement of parts. NOTE: Ensure the power supply is not connected while assembling the log splitter. STEP 1: Remove all the components from the crate. Inspect each piece for shipping damage. If any part is damaged, contact your dealer or delivering carrier. STEP 2: Connect the control handle bar.
DIRECTIONS FOR FILLING HYDRAULIC SYSTEM 1) Disconnect the control hand bar from its linkage part and take off the cushions from the front frame. 2) Lift the towing handle and keep the tank in the vertical position. 3) Disconnect the vent plug and dipstick from the front cylinder cover. 4) Put the front frame of the unit in some container; raise the wheels 2 in. off the ground on blocks, and drain the hydraulic tank. 5) Refill the tank within the marked range on the dipstick.
1) Place the log splitter on a sturdy, level surface. 2) Ensure the equipment is in safe working condition. Check all nuts, bolts and hydraulic fittings are tight. Check the switch, power cable and plug are not damaged. Check that all safety shields are in proper position. 3) Check that the outlet’s main voltage and frequency match the data stated on the model plate (or “Technical Specifications” in this manual). 4) Plug in the power cable and switch on the motor.
PARTS BREAKDOWN FOR 40100500 LOG SPLITTER R E FE R E N C E N U MB ER 1 Tank wi th wedge 39-44 2 Ram 45-49 3 Base plate of ram 50 D ESC R IPTION Key swi tch assembly C apaci tor assembly Rubber cover 4 Spri ng washer 51-52 C onnecti ng box cover assembly 5 Snap head bolt 53-54 Wi ring board assembly 55-57 6 Nylon li ner 7 Oi l fi lter 58 8 Oi l tube 59-65 C able fastener assembly Power cable and plug Motor rear end plate assembly 9 Seal ri ng 66 Motor frame cushi on 10 Bored
PARTS BREAKDOWN FOR 40100500 LOG SPLITTER Page 10
NOTES Model No. ____________________ Serial No.
SPECIFICATIONS MAXIMUM SPLITTING FORC E 5 Tons ELEC TRIC AL REQUIREMENT 110V/60Hz POWER INPUT 1960W POWER OUTPUT 1500W RATED C URRENT 12A MOTOR SPEED 3400 RPM POWER C ABLE 3G 1.0mm2 HYD RAULIC C APAC ITY C YC LE TIME MAXIMUM LOG LENGTH MAXIMUM LOG D IAMETER 3.3 Quarts 14 seconds 20" 9" HYD RAULIC PRESSURE 20MPa MAXIMUM C YLIND ER STROKE 20-1/2" TIRE SIZE MAC HINE D IMENSIONS (LXWXH) WEIGHT 7" 38-1/4" x 11" x 18" 105 lbs.
