Installation Guide

ManualsBrandsSpectrum ManualsAccordion DoorsEcho 36-in x 80-in White PVC Accordion Door (Hardware Included)

Echo

/Fusion Installation Instructions

For quick and easy installation of your folding door, read

these instructions thoroughly.

The Tools You Will Need

You will need a Drill, Phillips screwdriver bit, 3/32” drill bit for

pilot holes, small Phillips head screwdriver, tape measure,

pencil, ne tooth hacksaw (for cutting the top track), safety

glasses and ne sandpaper (can be used to smooth edges

after cutting top track) and a level.

Make sure all of the following Parts are

included before you begin:

Door Parts Location

SINGLE DOOR INSTALLATION

1. Measure the Door Opening

Measure the height and width of your nished opening. This

door ts openings that are 24” to 36” wide and 80” high.

If the height of your

door opening is

approximately 80”,

you will not need to

alter the height of the

door. If the opening

is less than 80” high,

the door may be

shortened by sawing

the excess from the

bottom of the door panels.

Trimming the Door Height and Top Track:

Stack the door panels together and secure with masking

tape. Remove bottom hinge screws. Cut excess o with a

hacksaw or le.

2. Install the Top Track

Cut the top track 1/8”

shorter than the width

of the nished opening.

Position the top track

in the top of the door

opening so that it is

straight and centered.

After making a pi-

lot-hole (with a 3/32”

drill bit), insert a 1”

track screw through

the pre-drilled hole

nearest the center of

the track. Do not fully tighten. (Tape may be used to hold the

track in place while you mark and drill.)

3. Attach the Handle

Tap the two handle

attachment pins into

one handle, then t the

pins through the door

panel holes. Press the

other handle onto the

pins.

If necessary, you may

back one handle with a

solid object and tap the

other handle alternately

over each pin area until

the handles are seated.

2 Ea.

Handles

1 Ea.

36” Top Track

1 Ea.

Closure

Channel

5 Ea.

Anchor

Channel

Clips

1 Ea.

Locking Clip

6 Ea. (1”)

Anchor Channel Screws

12 Ea. (1”)

Flat Head

Screws

1 Ea.

Locking Clip

Screws

Top Track

Closure

Channel

Handle

Top Glide

Anchor

Panel

Lead

Edge

2 Ea.

Handle Pins

1 Ea.

Spare

Top Glide

1 Ea.

Spare Top

Glide Screw

Anchor

Channel

Clips

Locking

Clip

Summary of content (3 pages)

PAGE 1
Echo/Fusion Installation Instructions For quick and easy installation of your folding door, read these instructions thoroughly. The Tools You Will Need You will need a Drill, Phillips screwdriver bit, 3/32” drill bit for pilot holes, small Phillips head screwdriver, tape measure, pencil, fine tooth hacksaw (for cutting the top track), safety glasses and fine sandpaper (can be used to smooth edges after cutting top track) and a level.
PAGE 2
Echo Installation Instructions 4. Hang Door onto Track Swing one end of the top track outward. Decide if the door will open from the left or the right, then slide all of the top glides onto the track. Stack the panels together near the center screw. Swing the track back to its original position. 6. Install the Anchor Channel Clips and Secure the Anchor Panel Use the closure channel to measure and align the channel clips. Align the channel on the non-opening side of the door jamb.
PAGE 3
Echo Installation Instructions 6. Install the Anchor Channel Clips and Secure the Anchor Panel Use the closure channel to measure and align the channel clips. Align the channel on the non-opening side of the door jamb. Make sure the top of the channel is straight up and down. Mark each of the five closure channel screw holes and remove the closure channel. Make pilot holes (with a nail or a 3/32” drill bit) and install the channel clips loosely, using five of the 1” roundhead screws.