Owners manual

ManualsBrandsSpectre Performance ManualsAutomotive9910 Air Intake Kit

Year/Make/Model/Engine

Intake Installation Instructions

P/N 9910 (red lter) - P/N 9910B (blue lter)

P/N 9910K (black lter) - P/N 9910W (white lter)

2007-2009 CHEVROLET CHEYENNE 5.3L

2007-2008 GMC YUKON XL 1500 5.3L, 6.0L, 6.2L

2007-2008 GMC YUKON DENALI 6.2L

2007-2008 GMC YUKON DENALI XL 6.2L

2007-2008 GMC YUKON 4.8L, 5.3L

2007-2008 GMC SIERRA DENALI 6.2L

2007-2008 GMC SIERRA 1500 4.8L, 5.3L, 6.0L

2007-2008 CHEVROLET TAHOE 4.8L, 5.3L

2007-2008 CHEVROLET SUBURBAN 1500 5.3L, 6.0L

2007-2008 CHEVROLET SILVERADO 1500 4.8L, 5.3L, 6.0L

2007-2008 CHEVROLET AVALANCHE 5.3L, 6.0L

2007-2008 CADILLAC ESCALADE 6.2L

Tools Required:

• 5/16” or 8mm nut driver

• Ratchet

• 10mm socket

• 13mm socket

Parts List

1 - Intake tube

1 - Air lter

1 - 4” Offset velocity stack adapter

1 – 3.5” Flex coupler

1 – 4” Hose clamp

3 – 3.5” Hose clamps

1 – 6” Hose clamp

1 - 90° Rubber elbow

2- Bolts, hex/ange

2- Lock washers

3- Allen bolts

3- Flat washers

3- Locknuts

1- Allen wrench

1 - Heat shield Pc 1

1 - Heat shield Pc 2

1- Rubber seal

1- 3/8” Breather hose

For lter reorders ask at the

special order counter of your

local parts store or call:

1-909-673-9800

ask for: P/N HPR9891 (red lter)

P/N HPR9891B (blue lter)

P/N HPR9891K (black lter)

P/N HPR9891W (white lter)

176149B

4/13/15

Summary of content (4 pages)

PAGE 1
Intake Installation Instructions P/N 9910 (red filter) - P/N 9910B (blue filter) P/N 9910K (black filter) - P/N 9910W (white filter) Year/Make/Model/Engine 2007-2009 CHEVROLET CHEYENNE 5.3L 2007-2008 GMC YUKON XL 1500 5.3L, 6.0L, 6.2L 2007-2008 GMC YUKON DENALI 6.2L 2007-2008 GMC YUKON DENALI XL 6.2L 2007-2008 GMC YUKON 4.8L, 5.3L 2007-2008 GMC SIERRA DENALI 6.2L 2007-2008 GMC SIERRA 1500 4.8L, 5.3L, 6.0L 2007-2008 CHEVROLET TAHOE 4.8L, 5.3L 2007-2008 CHEVROLET SUBURBAN 1500 5.3L, 6.
PAGE 2
Step 1 Safety first! Before you begin the installation, make sure that the vehicle is in park (or neutral for a manual transmission) with the parking brake set. Disconnect the negative battery terminal and verify that all components that are listed are present. Note: This kit was designed and tested on a stock engine without any custom tuning done to the engine computer. Removing the battery cable may erase the programmed radio stations.
PAGE 3
Step 7 Remove the air box assembly by pulling up and out firmly. Step 8 Remove the air box mounting plate. Two of these bolts will be re installed with the new heat shield. Step 9 Remove the MAFS from the factory air box making sure the factory boot stays on the MAFS. Step 10 Assemble the heat shield with the tabs placed on the outside of heat shield. Install bulb seal around edges of heat shield as shown.
PAGE 4
Step 15 Connect the supplied hose to the breather tube on the motor. Step 16 Install the flex coupler on the end of the MAFS and secure the boot in place. Install a second clamp but do not tighten at this time. Step 17 Install the intake tube as shown and once in position tighten clamps. Step 18 Reconnect the MAFS wiring harness. Step 19 Install the new hose onto the vacuum fitting on the intake tube. Step 20 Install the filter and fully tighten the clamp. Step 21 Reinstall the engine cover.