User's Manual

11
安裝指南
Installation Guide
清潔印表機
分開終端與電源線的連接
Printer Cleaning
Disconnect power cable from the terminal
維修運送：
如需要把 T1000 運送到維修部門, 請先和代
理商聯繫, 並把 T1000 打包，最好使用原廠
包裝，確保在運送途中不會損壞。
Send for repairing
If it is necessary to send back T1000 for
repairing, please contact agency, pack the
terminal properly (use original packing
material if possible) to avoid damage during
transportation
開啟紙斗蓋, 取出軸心及紙卷
清除紙斗中的紙屑及灰塵，如果可能的話，可
使用低壓吹風器
不要觸摸打印機頭及切紙刀
Open printer cover, take out paper and roller
Remove dust and paper scrap inside paper
tray . Use low pressure blower to clean the
paper tray if possible.
Do not touch the thermal printer head and
paper cutter during cleaning
Put back paper and roller into paper tray
Close the printer cover
合上紙斗蓋
放回紙卷
4.5 故障排除
Trouble Shooting
T1000 的產品設計力求穩定可靠，但在安裝
和使用的過程中可能出現一些小問題，在準
備送修之前，可自行作出以下簡單的解決辦
法，如果問題仍未解決，請與代理商聯繫，
禁止私自拆卸終端機
1、如從電源適配器 ，檢查電源線接口、電源
適配器接口是否穩固地插牢
取電
2、如從電源適配器 ，請連接一個其他設備於
AC 電源，檢查AC 電源有沒有電壓，如懷疑
AC 電源存在問題，請聯 繫專業電工進行檢查
取電
3、如從電源適配器 ，請嘗試更換另一 T1000
的 AC/DC 電源適配器
取電
再試
4、如從電源適配器 ，請嘗試更換另一電源
插座來連接電源適配器
取電
5、嘗試調節LCD液晶顯示幕的對比度
6、如問題仍未解決，請與代理商聯繫
交易不成功：
1、更換另一張磁卡或IC卡進行交易
4、如問題仍未解決，請與代理商聯繫
2、檢查插卡或刷卡方式是否正確
3、如交易仍失敗，請檢查所有連接線末端的連
接是否正常
T1000 has been designed to provide stable
service for users. However, there would be
some minor problems during in use. Before
sending back for repairing, users can try the
following simple procedures to fix the
problems themselves
出現“死機”情況：
Terminal not function
1, If it is powered by power adaptor, check
whether the connection of power cord or
power adaptor is connected properly
2, If it is powered by power adaptor, try to check
whether the AC source is error free by
plugging with other electrical appliance
3, If it is powered by power adaptor, try to
replace the adaptor with another one
4, If it is powered by power adaptor, try to
replace the electric power socket with another
one
5, Try to adjust the LCD contrast
6, Contact agency if problem cannot be solved
Unsuccessful transaction
1, Try to use other magnetic card or IC card for
transaction
2, Check whether the way of swiping card or
inserting card is correct
3, Check whether all wire ends are connected
properly
4, Contact agency if problem cannot be solved
SPECTRA T1000