SURVEY PRO for Ranger Reference Manual © 2007 Tripod Data Systems, Inc.
TRIPOD DATA SYSTEMS SOFTWARE LICENSE AGREEMENT IMPORTANT: BY OPENING THE SEALED MEDIA PACKAGE, YOU ARE AGREEING TO BE BOUND BY THE TERMS AND CONDITIONS OF THE LICENSE AGREEMENT AND LIMITATIONS OF LIABILITY ("Agreement"). THIS AGREEMENT CONSTITUTES THE COMPLETE AGREEMENT BETWEEN YOU AND TRIPOD DATA SYSTEMS, INC. ("Licensor").
Table of Contents Reference Welcome.................................................................................................. 1 Main Menu............................................................................................. 3 File Menu................................................................................................ 7 Open / New .............................................................................. 8 New Job...............................................................
Traverse / Sideshot .............................................................. 124 Repetition Shots .................................................................... 130 Multiple Sideshots ................................................................ 132 Radial Sideshots .................................................................... 133 Distance Offset Shot ............................................................. 134 Horizontal Angle Offset ..............................................
File Management .................................................................. 243 Survey Menu – Basic GPS ............................................................... 245 GPS Status.............................................................................. 246 Start GPS Survey................................................................... 246 Data Collection...................................................................... 253 Control Points...............................................
Curve and Offset................................................................... 342 Spiral and Offset ................................................................... 342 Show Station and Offset ...................................................... 343 Store Offset Points ................................................................ 344 Stake DTM ............................................................................. 345 Where is Next Point...................................................
Straight Grade ....................................................................... 394 Spiral....................................................................................... 395 Spiral Layout ......................................................................... 396 Traverse on Spiral................................................................. 397 Roads Menu ....................................................................................... 399 Add/Edit Templates ....................
Welcome Congratulations on your decision to purchase a Tripod Data Systems product. TDS is serious about providing the best possible products to our customers and know that you are serious about your tools. We are proud to welcome you to the TDS family. The TDS Survey Pro team is continually improving and updating Survey Pro. Please take a few minutes to register your copy so that you will be eligible for upgrades.
Main Menu The Main Menu is the starting point where all the other Survey Pro screens described in this manual are accessed. The area at the top of the screen is called the command bar. The small buttons in the command bar are used as follows: Online Help Tapping the button opens the online help, which allows you to access information similar to the information you would find in the reference manual for each screen.
Survey Pro Reference Manual Tapping the battery icon is a shortcut to the Microsoft Power Settings screen. You can view the online help for this screen on a Ranger then , or on a Ranger by tapping . 300X/500X by tapping Surveying Mode The instrument icon indicates which collection mode the software is running in. There are three possible surveying Conventional, GPS, and Leveling. Tapping modes: this icon will open a list of options to do any of the following: • Switch to another instrument mode.
Main Menu GPS Status This is used to view the current status and access the settings for a GPS receiver when using the GeoLock feature (Page R-162). It is only available from the Remote Control and Remote Shot screens when using a Trimble or Geodimeter robotic total station.
File Menu The File Menu contains routines to transfer files between the data collector and another device.
Survey Pro Reference Manual Open / New File Open / New. The Open / New screen is used to open an existing job or create a new one. This screen also appears when Survey Pro is first started. Open : will open the job selected in the Open a Recent Job list. Browse… : will open the Open screen (Page R13) where an existing job to open can be selected. New… : will open the New screen (Page R-8) where a new job can be created. New Job File Open / New New…. The New Job wizard is used to create a new job.
File Menu Next > : opens the next screen. The screen that opens depends on if a control file will be used. Create a New Job 2 – (Imported or External Control File) This screen will only open next when a control file will be used or imported. Import Control Points: When selected, the points in the control file will be imported into the new job. Use External Control File: When selected, the control points in the control file will be accessible from the new job, but will not be imported.
Survey Pro Reference Manual Create a New Job 3 Azimuth Type: specifies if you are surveying with a North Azimuth or South Azimuth. Units for Distances: specifies if your distances will be entered in International Feet, U.S. Feet, or Meters.
File Menu Create a New Job 4 – (Imported Control File) This screen will only open when a control file is being imported. Screen when checkbox is unchecked. Screen when checkbox is checked. Enter First Point: when this box is checked, the additional fields will appear allowing you to create a new point. Note: Although all new jobs must have at least one point, creating a new point when importing a control file is optional since points are already being loaded into the job in the form of control points.
Survey Pro Reference Manual Create a New Job 5 – (External or No Control File) Point Name: is the name of the initial point. Northing: is the Y-coordinate of the initial point. Easting: is the X-coordinate of the initial point. Elevation: is the elevation of the initial point. Description: is the description of the initial point. < Back : returns you to the first screen. Finish : stores a new job file and raw data file using the specified information.
File Menu Open File Open / New. Browse…. The Open screen is used to open an existing job. A list of all the jobs in the current directory is displayed. Simply tap on the job name that you want to open and then tap . Note: TDS CR5 files can be opened just like any Survey Pro JOB file. When a CR5 file is opened, it is automatically converted and stored to a JOB file with the same name.
Survey Pro Reference Manual Save As File Save As. The Save As screen allows you to save a copy of the current job under a new name. The copy that is created will then become the current job. The Save As dialog box is identical to that found in the Windows operating system. Simply enter a new name for the current job and then tap the Save button. Note: It is not necessary to include the .JOB extension since it will automatically be added for you.
File Menu Import File Import. The Import screen is used to add the points from another source into the current job or import the data from a LandXML file to the current job. Warning: Coordinate values can change when they are imported! Importing coordinates from any source other than a JOB file requires that the distance units used in the source file be specified. It is not necessary to specify the distance units when importing coordinates from a JOB file since those units are written within the file.
Survey Pro Reference Manual Coordinates from a variety of file types can be imported into the current job. The first Import Coordinates screen is used to select from the file types listed below. The next screen that opens depends on the selection made here. • Job Files (*.JOB): import coordinates from another Job file. • Coordinate Files (*.CR5): import coordinates from a TDS CR5 coordinate file. • GPS Files (*.GPS): import coordinates from a TDS GPS coordinate file. • Text Files (*.
File Menu Import *.CR5 Coordinates When importing a CR5 file, you will first be prompted to select the layer where you want the new data stored. Select a layer and tap to continue. In the next screen, select the distance units that the coordinates were stored in and tap . Import *.GPS Coordinates When importing a GPS file, you will first be prompted to select the layer where you want the new data stored. Select a layer and tap to continue.
Survey Pro Reference Manual Import *.TXT Coordinates When importing a TXT file, you will first be prompted to select the layer where you want the new data stored. Select a layer and tap to continue. Since the coordinates in an ASCII TXT file can be stored in a variety of formats, two screens are used to define the format of the file that is being imported once a layer is selected. The source TXT file can contain either plane coordinates or geodetic coordinates.
File Menu Import *.TXT Coordinates – Screen Two Name Column No. / Start Point Name. When the first option is selected here, the column number used for the name field in the *.TXT file is specified here. When the second option is selected, it is assumed that the *.TXT file does not contain point names and will assign the first point the name specified here and increment to the next available point name for the remaining points.
Survey Pro Reference Manual Import LandXML Coordinates Points, alignments, polylines, and parcels can be imported from a LandXML file. The way the LandXML data is imported depends on how the data is stored in the source file and how the settings are configured in the two screens described below. Consult the User’s Manual for more information on the conditions that affect how the data is imported. On specified layer: will import all the data on the specified layer.
File Menu Lines can either be assigned the name or description from the source file and points can either be assigned the description or code from the source file. Back : returns to the previous screen. Import : imports the specified data into the current project. A results screen will open listing the details of the imported data.
Survey Pro Reference Manual Start At: is the point name assigned to the imported point when using the Renumber or Renumber All functions. Compare coordinates… : will open a dialog box showing the coordinates for the duplicate points to assist in making a decision of how to handle the new point. Stop Importing : will not import the current duplicate point and will stop importing any remaining points. All previous points will still be imported into the current job. Export File Export.
File Menu Next > : opens the next screen, which is determined by the selected file type. Export – Screen Two The second Export screen will open for any file type that was selected in the previous screen except LandXML. This screen is used to select the points from the current project that you want to export to the selected file type. (Exporting to a LandXML file is described later.) To/From… : Opens the Point List screen (Page R-443) where a point list can be created.
Survey Pro Reference Manual Export *.CR5 Coordinates The Export CR5 dialog box will open when exporting coordinates to a TDS CR5 coordinate file. CR5 File Options: specifies if the resulting file should be Sequential or Non-Sequential. (The HP 48 data collector can only use sequential coordinate files.) < Back : returns to the previous screen. Export : exports the selected coordinates to the new CR5 file. Export *.TXT Coordinates Since the coordinates in an ASCII *.
File Menu Next > : opens the second screen. Export *.TXT Coordinates – Screen Two Select the desired order and format for the resulting TXT file from the list of options. Finish : exports the selected points to the TXT file. Export *.CSV Coordinates This routine is identical to the Export *.TXT Coordinates routine, described above with the exception that the formatting for the exported file is automatically set to comma delimited and the extension for the file name will be *.CSV.
Survey Pro Reference Manual Export LandXML (.XML) File Unlike the other export routines, which only export points, the LandXML export routine allows you to export points along with polylines and alignments. Export polylines and alignments: will export the points in the current project as well as any polylines and alignments. If this is unchecked, only the points will be exported. Export polylines on the specified layer as parcels: will export the polylines on the selected layer as parcels.
File Menu external control file are also used in the current job, the control file cannot be used.) Backup / Restore Job File Backup / Restore. The Backup / Restore wizard is a series of screens that are used to backup or restore all the files associated with the current job. The routine also gives you the option of storing a snapshot of a customized map view to the archive. This can then be used to visually identify an archive. Any number of backups can be created for a particular job.
Survey Pro Reference Manual Properties… : opens the Archive Properties screen. Backup: when selected, tapping Next> will begin the backup routine where the data for the current job will be stored to the selected archive. Restore: when selected, tapping Next> will begin the restore routine where the data from the selected archive will be restored, overwriting the current job. Next> : opens the next screen. Backup / Restore - Archive Properties File Backup / Restore Properties….
File Menu Backup / Restore – Backup When performing a backup, all the files associated with the current job are listed and will be included in the archive. ; Create Snapshot: When checked, the next screen will prompt you to create a snapshot of the current job’s map view, which will then be included in the archive. < Back : returns to the previous screen. Backup : opens the next screen.
Survey Pro Reference Manual Backup/Restore – Restore When restoring the job files from an archive, the archived files will replace the existing files of the current job. Warning: If you do not want to lose any new data that was collected after the archive being restored was created, you should first backup the current job to a new archive before restoring an older archive. < Back : will return to the previous screen. Restore : will restore the backed up job from the selected archive.
File Menu Transfer File Transfer. The Transfer screen allows you to transfer files between the data collector and another device running TDS software. Connecting to: specifies which device you are communicating with from the following options: • HP48: if you are connecting to a Hewlett Packard HP48 calculator. • Husky: if you are connecting to a Husky FS-series data collector. • Ranger / TSCe / ACU / Pocket PC: if you are connecting to any of the devices listed.
Survey Pro Reference Manual that indicates how much of the file has been transferred. Tapping Cancel will stop the file transfer. Note: The Send routine should be initiated shortly after issuing the receive command on the other device. Receive File… : allows you to receive a file from another device. This should be tapped prior to issuing the Send command on the other device. Tapping Cancel will stop the file transfer. Register Modules File Register Modules.
File Menu Enter Registration Code : Opens the Register screen, shown here, where the registration number for a particular module can be entered. About Survey Pro File About Survey Pro. The About screen displays the version of the Survey Pro software and the versions of several of the Survey Pro software files, which can be updated from the TDS Website. Hardware Information : is a shortcut to the Microsoft System Properties screen. Exit File Exit.
Job Menu A: Settings B: Edit Points C: Edit Polylines D: Edit Alignments E: Auto Linework F: View Raw Data File G: View DTM H: Manage Layers I: Job Information J: Calculator R-35
Survey Pro Reference Manual Settings Job Settings. See Page R-94 if running in GPS mode. The Settings screen actually consists of several separate screens where each individual screen contains different types of settings. There are two ways to navigate to the various screens. The first method is to tap the button to drop down the list of available screens and then tap on the desired screen from the list to open it.
Job Menu Note: When running in leveling mode, the Instrument Settings… can be selected for Manual Mode to open the Level Method screen described on Page R-41. Instrument Settings : opens the next Instrument Settings screen where the settings in the selected instrument profile can be modified. Note: When editing an existing instrument profile, you cannot modify the instrument brand or model.
Survey Pro Reference Manual Instrument Settings – Screen Two The second Instrument Settings screen opens whenever a new instrument profile is being created, or when an existing profile is being edited. The options available on this screen will vary slightly depending on the total station model selected. Name: is the name of the instrument profile being created or changed. This is the name that appears in the list on the first Instrument Settings screen.
Job Menu was entered in the total station. These numbers must match for successful communications. Bluetooth… : (applicable only when using Bluetooth with a supported total station) accesses the Bluetooth configuration screen that comes with the Bluetooth driver software where you can quickly check or change the virtual COM port and favorites. Note: See the User’s Manual for more information on configuring Bluetooth with a supported total station.
Survey Pro Reference Manual NOTICE: The settings that are available after tapping the Instrument Settings… button directly control the settings that are built into the selected total station. Since total station manufactures release new models every year, TDS cannot maintain the necessary set up documentation for every existing model and the models that are not yet available.
Job Menu Level Method Job Settings Instrument (select Manual Mode) Instrument Settings… The Level Method screen is used to select the leveling method you want to use while running in leveling mode and while using Manual Mode. This will affect the type of data you are prompted for when taking shots. Three Wire: Prompts for shot data will require upper, center, and lower wire readings. Single Wire: Prompts for shot data will require center wire readings only.
Survey Pro Reference Manual Note: You can enter a distance in any distance field in units other than what is set for the job by appending the distance value with the following characters: y f or ft or ift y usf or usft y i or in ym y cm y mm y c or ch International Feet US Survey Feet Inches Meters Centimeters Millimeters Chains Once the cursor leaves that field, the distance will be converted automatically. (A space between the value and the unit abbreviation is optional.
Job Menu Format Settings Job Settings Format. The Format Settings card defines the number of places beyond the decimal point that are displayed for various values in all screens, and how stations are defined. (All internal calculations are performed using full precision.) Northings / Eastings: will allow you to display from zero to six places passed the decimal point for northing and easting values. Elevations: allows you to display from zero to six places passed the decimal point for elevations.
Survey Pro Reference Manual Files Settings Job Settings Files. Description File: allows you to select a description file to use with the current job. ; This file uses codes: check this box if the description file contains codes and associated descriptions. Leave the box unchecked if the description only contains descriptions (no codes). Feature Code File: displays the selected feature code file to use with the current job. See the User’s Manual for more information on feature codes.
Job Menu Surveying Settings Job Settings Surveying. The Surveying Settings card allows you to select various options that affect how data collection is performed. ; Prompt for Description: When checked, a prompt for a description will appear before any new point is stored from only the routines under the Survey menu (Page R-117). Note: Descriptions cannot exceed 16 characters. ; Prompt for Height of Rod: When checked, a prompt for the rod height will appear before any new point is stored.
Survey Pro Reference Manual ; Survey with True Azimuths: automates the process of adjusting the circle on the total station when traversing so that you can survey with azimuths rather than horizontal angles (see Page R-127). ; Use Scale Factor: when checked, horizontal distances to all new points will be scaled by the factor entered here. (Elevations are not affected.) This defaults to unchecked when a new job is created. Calc.
Job Menu Stakeout Settings Job Settings Stakeout. The Stakeout Settings card contains the setting that control how stakeout is performed. (The settings available depend on if you are running in conventional or GPS mode.) ; Stake “Corners,” Not Just Even Intervals: when staking by stations, locations where a line segment changes, such as from a straight section to a curve, will also be staked when this is checked.
Survey Pro Reference Manual Note: If the specified offset extends beyond the end of the road profile, the cut/fill value is always computed from the design elevation of the node you are staking to. ; Write Cut Sheet Data Only (No Store Point): When checked, asbuilt points are not stored to the JOB file when staking points; only the raw data is written to the RAW file. ; View from Gun to Rod (non-remote): When checked, the move left or right information will be presented from the rod person’s point of view.
Job Menu screen that is displayed when you are near the stake point will occur when you are within the distance to the stake point specified here. Line Tolerance: this setting affects the Stake to Line routine (Page R-282). When staking to a line and the prism is located at a perpendicular distance to the specified line that is within the range set here, a message will state that you are on the line. Horizontal Distance Tolerance: This setting affects the GPS staking routines.
Survey Pro Reference Manual • Northing / Easting: will suggest you Go South/Go North and Go West/Go East • Distance / Azimuth: will display the necessary Azimuth and Distance to the stakeout location. • Forward / Back: will suggest you go FORWD/BACK and Go Left/Go Right when you are within 3 meters to the location. When you are farther than 3 meters, a distance and azimuth is used. Level Settings Job Settings Level. The Level Setting screen is only available when running in leveling mode.
Job Menu H Dist Tolerance: is the maximum change in horizontal distance that can occur between all the shots to any specific point from a single setup. If this value is exceeded, a warning will occur. ; BS-FS Sight Length < Per Shot: When checked, a warning will occur whenever the horizontal distance of each leg in any given setup differs by more than this value.
Survey Pro Reference Manual FGCS Defaults Job Settings Level Load FGCS Defaults. The FGCS Defaults screen is used to load the default FGCS tolerances in the Level Settings screen for the order and class of level loop specified here. Order: indicates the order of the level loop that you want to load the default tolerances for. Class: indicates the class of the level loop that you want to load the default tolerances for.
Job Menu Repetition Settings Job Settings Repetition. The Repetition Settings card contains the settings that control how repetition shots are performed and acceptable tolerances. Horizontal Tolerance: a warning message will be displayed if a horizontal angle exceeds the tolerance entered here during a repetition shot. Zenith Tolerance: a warning message will be displayed if a vertical angle exceeds the tolerance entered here during a repetition shot.
Survey Pro Reference Manual • FS > BS ^ BS > FS: Foresight, Backsight, flop Backsight, Foresight • FS > BS ^> FS > BS: Foresight, Backsight, flop Foresight, Backsight • BS ^ BS ^ > FS ^ FS ^: Backsight, flop, Backsight, flop, Foresight, flop, Foresight, flop Date/Time Settings The Date/Time Settings card is used to set the date and time in the data collector. Date: displays the current date. Time: displays the current time.
Job Menu Buttons Settings This screen is available on the Ranger 300X/500X only. The Buttons Settings card is used to customize the function for the physical buttons located on the data collector. The upper half of the screen lists all of the customizable button’s current assignments. A particular button must be selected from this list prior to changing its settings from the lower half of the screen.
Survey Pro Reference Manual General Settings The General Settings card can contain the following miscellaneous settings: ; Use Enter Key to Move Between Fields: When checked, the [Enter] key will move the cursor to the next field in all screens. When unchecked, the [Enter] key will perform a different function depending on the field selected. Note: The arrow keys and the [Tab] key can also be used to move the cursor between fields.
Job Menu ; Prompt for Layer: When checked, a prompt to select a layer will appear before any new point is stored from any routine other than those included in the Survey and Stakeout menus. ; Prompt for Attributes: When checked, a prompt to select feature information will appear before any new point is stored from any routine other than those included in the Survey and Stakeout menus. This also requires that a feature file be selected from the Files Settings card, described earlier.
Survey Pro Reference Manual Edit Points Job Edit Points. The Edit Points screen allows you to add, edit, and delete any points in the current job. Edit… : if only a single point is selected, this will open the point in the Edit Point - General screen (Page R-60) where the details of the point can be modified. If more than one point is selected, the next Edit Points screen will open where the description and layer for the selected points can be modified simultaneously.
Job Menu Go To… : opens a dialog box where any point can be quickly located by the entered point name. Edit Multiple Points – General Job Edit Points Edit… General. The General and Location cards of the Edit Points screen are accessed after pressing Edit… when more than one point is selected. The changes made in these screens will be applied to all the selected points.
Survey Pro Reference Manual Edit Multiple Points – Location Job Edit Points Edit… Location. Elevation: when checked, this allows you to enter an elevation that will be applied to all selected points. Edit Point – General Job Edit Points Edit… General. The General card of the Edit Point screen is used to modify the description, layer and feature information for the selected point. Point Name: displays the selected point’s name. Description: is the description for the selected point.
Job Menu Point Feature Attributes Job Edit Points Edit… General Attributes…. The Point Feature Attributes screen is available from the above path or whenever a point is stored when Prompt for Attributes is checked in the Surveying Settings screen (Page R-45). Recently Used: when checked will arrange the order of the available features so the most recently used features are listed first. Any feature in the current feature file can be selected from the corresponding drop-down list.
Survey Pro Reference Manual Edit Point – Geodetic Job Edit Points Edit… Geodetic. The Geodetic card applies primarily to Survey Pro with GPS users. Refer to the GPS Reference Manual for more information on this card. ; Has Geodetic Data: when checked, this allows you to edit the geodetic coordinates for a point. Advanced… : will open the Edit GPS Point Flags screen to select the advanced settings for the selected point.
Job Menu Edit GPS Point Flags Screen Survey Control Points Edit Point Set Flags. The Edit GPS Point Flags screen is used to select the advanced settings for the selected point. Set Up Group: is the set up group of the point. (See the User’s Manual for more information on set up groups.) GPS Control Point: When checked, will include the selected point in the list of localization control points.
Survey Pro Reference Manual Edit Polylines Job Edit Polylines. The Edit Polylines screen is used to add, edit, and delete polylines in the current job. The first screen will display a list of all the polylines that are stored in the current job. Selecting any of the polylines listed will display a horizontal (overhead) and vertical (side) view of that polyline. New… : will open the Polyline Editor where a new polyline can be created.
Job Menu Edit… : Opens the third screen, described next, where the current polyline can be modified. Clear : removes the current polyline. Screen Three – Polyline Editor Once the initial points are selected for the current polyline, the third screen allows you to modify the polyline and define any curve and grade information for the polyline sections. Selecting any point in the left column of the screen will select that point and the line segment that follows it up to the next point.
Survey Pro Reference Manual Note, if is selected in the list, the <-Insert button will change to an <-Append button to indicate that additional points will be appended to the end of the list. Screen Four – Add/Edit Curve The fourth screen is used to modify a selected polyline segment that occurs between two points. A horizontal, vertical, and/or spiral curve can be applied to the polyline segment. Adding a Horizontal Curve Tap the Arc / Spiral tab.
Job Menu Adding a Spiral Tap the Arc / Spiral tab. Curve: must be set to Spiral to enter a spiral curve. Radius: is the radius of the spiral curve. (The same radius of the circular curve adjacent to the spiral.) Length: is the length of the spiral, measured along the curve from the TS to the SC. Turn: specifies if the spiral curve turns to the Right or Left as you occupy the initial point and face the end point.
Survey Pro Reference Manual Edit Alignments The Edit Alignments screen is used to create and edit alignments, which can then be used with routines such as Offset Staking, Offset Points, Offset Lines and Road Layout. Alignments are used to describe all of the horizontal and vertical details of a road’s centerline.
Job Menu • Create Points: opens the Create Points screen (Page R-440) where points can be stored that coincide with the selected alignment. • Import .RD5 File: opens the Open screen and lists all the *.RD5 alignment files in the Jobs directory. Select the desired file and tap . • Export .RD5 File: opens the Save As screen where the current alignment can be saved to a *.RD5 file. Edit Alignment Job Edit Alignments Edit…. or Job Edit Alignments New….
Survey Pro Reference Manual Edit Alignment Screen – VAL Tab The VAL (Vertical ALignment) tab in the Edit Alignment screen is used to enter or modify only the vertical details of an alignment. Note: The total horizontal length of the VAL must be equal to or greater than the total horizontal length of the HAL when the alignment is used for road layout. Insert… : opens the Edit Segment screen where a new vertical segment can be inserted prior to the selected segment.
Job Menu Start Station: is the station on the alignment that corresponds with the starting location or point. Edit Alignment Screen – General Tab The General tab in the Edit Alignment screen is used to describe the alignment and select the layer where it is located. Description: is the description of the alignment. Layer: is the layer where the alignment will be located. Attributes : opens the Point Feature Attributes screen (Page R-61) where the feature attributes for the alignment can be selected.
Survey Pro Reference Manual Note: When making a new horizontal segment tangent to the previous segment, the new segment will appear in the Edit Alignment screen tagged with a (P). This means that if the previous horizontal segment is edited or deleted, where the orientation changes, all subsequent horizontal segments that have the (P) tag will also be adjusted so they will remain tangent to the previous segments. Azimuth / of the line.
Job Menu Turn: specifies if the curve turns to the the curve from the beginning. Left or Right as you face ; Make this segment tangent to previous: When checked, the start of the specified curve will be tangent to the ending tangent of the previous segment. Azimuth / Bearing : is used to enter a known azimuth or bearing at the start of the curve. : adds the curve to the current horizontal alignment. Edit Segment – Spiral Card The Spiral card is used to add a spiral curve to the alignment.
Survey Pro Reference Manual Edit Segment – Vertical Line Card (Grade) The Vertical Line card is used to enter a segment with any grade. Length: is the horizontal length of the segment. Grade: is the grade (slope) of the segment. Get Previous Grade : will automatically enter a grade equal to the grade at the end of the previous segment. Edit Segment – Vertical Curve The Vertical Curve card is used to enter a parabolic vertical curve to the alignment. Length: is the horizontal length of the vertical curve.
Job Menu Auto Linework Job Auto Linework. The Auto Linework screen is used to set up custom descriptors that can be used to generate various polylines between points as they are shot. These features can than be exported and used in the TDS ForeSight software. Note: The auto linework information described below is not written to the raw data file.
Survey Pro Reference Manual description is at all different from the previous use, a new independent line segment will be drawn. For example, if LOT# were used as in the screen shown above, all entries of “LOT10” would be connected. If LOT15 were also used as a description during data collection, any future use of LOT15 would connect to the previous LOT15 entry. Note: Linework descriptions are case sensitive.
Job Menu • T-Crv : creates a curve with a specified incoming tangent from the next two points that are stored with a description associated with T-Crv. When the second point is stored, the prompt shown here appears where the incoming azimuth or bearing is specified. • Rect : will compute and store the fourth and final point that forms a rectangle or parallelogram after three points are stored with a description associated with Rect.
Survey Pro Reference Manual If the button is blank and the current job contains at least one polyline, you will be prompted to select an existing polyline. Once selected, future points stored with this linework command will be appended to the selected polyline. Props: A single polyline can contain different line types.
Job Menu View Raw Data File Job View Raw Data. The View Raw Data File screen displays the raw data file of the current job and allows you to append a note or current time entry. Tapping any line in the raw data file will toggle a bookmark in front of that line. The active bookmark is shown as a green circle. An inactive bookmark is shown in red. First : jumps to the first line of the file. Last : jumps to the last line of the file. Prev. : jumps to bookmark above the active bookmark.
Survey Pro Reference Manual Raw Data Note Enter any note to append to the raw data file. You can use the buttons to insert common line work commands. When finished, tap Write Now! to append the note to the end of the raw data file. View DTM Job View DTM. Before viewing a DTM, the Setup DTM 3D screen will open where the DTM layers must be defined. This screen is also used to define other parameters for the DTM. Layers : opens the Layers for Staking DTM screen where the DTM layers are selected.
Job Menu Breaklines… : will open the Add/Edit Break-lines screen where DTM break-lines can be added or edited. Points… : will open the Points on DTM Layer screen where the points on the DTM layer can be viewed, new points can be imported, and existing points can be deleted (moved to the Auxiliary layer). 3D View… : will open the 3D View screen where the DTM can be viewed from any angle. Layers for Staking DTM Job View DTM Layers….
Survey Pro Reference Manual Choose Polyline Job View DTM Boundary…. The Choose Polyline screen is used to select an existing polyline that defines a boundary for your non-reference DTM surface. All the polylines in the current job are displayed. Select the appropriate polyline and tap . Add/Edit Break-lines Job View DTM Breaklines…. The Add/Edit Break-lines screen is used to select, edit, create, or delete the break-lines that will be used when computing the DTM.
Job Menu Edit Polyline Job Job View DTM View DTM Breaklines… Breaklines… Edit… or New…. The Edit Polyline screen is used to perform some preliminary editing to a polyline prior to accessing the polyline editor with the Edit… key. Tap Points… : allows you to tap points to define a new polyline. If a polyline was already selected prior to accessing this screen, it will be replaced by the polyline being created. To / From… : allows you to define a range of points that define a polyline.
Survey Pro Reference Manual Points on DTM Layer Job View DTM Points…. The Points on DTM Layer screen displays all the points on the DTM layer and allows you to add points from another layer or delete (move) points to a different layer. Delete : will move the selected point(s) to the Auxiliary layer. If the Auxiliary layer is not specified, you will be prompted to select the layer to move the points to. Note: Points on a boundary or break-line cannot be deleted.
Job Menu 3D View Job View DTM 3D View…. The 3D View screen is used to view the DTM from any angle. Setting : opens the 3D View Settings screen, described below, where the information displayed in the 3D view can be configured. Volume : displays the total cut and fill volume between the area that has been staked and a reference datum, whose elevation is specified in the 3D View Settings screen; or the total cut and fill between the area that has been staked and the selected DTM.
Survey Pro Reference Manual Height Exaggeration Ratio: is the value that the height is multiplied by in the 3D view. The higher this value, the more exaggeration, where 1.0 would result in no exaggeration. ; Hidden-line Removal: When checked, will hide all the lines that occur behind other surfaces in the 3D View. The image shown here is identical to the image shown on Page R-85 except the hidden lines are not removed. ; Display the Difference: This applies only to DTM stakeout.
Job Menu Manage Layers Job Manage Layers. The Manage Layers screen is used to manage the layers for the current job. All existing layers are displayed along with which layers are visible and how many objects are on each layer. Set Active : will set the selected layer as the active layer. The active layer is marked with a symbol. New… : opens the New Layer dialog box where a new layer can be added. You are prompted for a name and if the new layer should be visible.
Survey Pro Reference Manual Job Information Job Job Info. The Job Information screen displays details of the current job and allows you to remove wasted space in the current job file. Filename: displays the current job file name. Control file: displays the control filename used in the current job. Feature Code File: displays the feature code filename used in the current job. Folder: displays the directory where the current job file is located. Size: displays the size of the current job.
Job Menu Recover Wasted Space Now : As you add and remove points and lines in a job, empty gaps can result within the job file. These gaps use storage space. This button will remove any gaps in the job file, thus recovering the wasted space. Note: Survey Pro checks for low memory situations every minute. When the available system memory falls below 256K of RAM, a warning is displayed.
Survey Pro Reference Manual Calculator Job Calculator. or , Calculator (where applicable) The Calculator screen behaves exactly like any other RPN-format calculator. It consists of a stack that can contain any number of values and buttons that perform various operations. When a value is being entered from the keypad, it is displayed in a special area called the active area. This value is then place in Level 1 of the stack after tapping the Enter key.
Job Menu √x: Square root of x. xn: Raises y to the power of x. 1/x: Inverse of x. Sin: Sine of x. Cos: Cosine of x. Tan: Tangent of x. 10x: Raises 10 to the power of x. ex: Raises 2.718281828 to the power of x. Sin-1: Arc sine of x. Cos-1: Arc cosine of x. Tan-1: Arc tangent of x. Log: Common logarithm (base 10) of x. Ln: Natural logarithm (base e) of x. R>P: Converts the rectangular coordinates (y,x) to polar coordinates. P>R: Converts the polar coordinates (y,x) to rectangular coordinates.
Job Menu – GPS Only the Settings menu item in the Job Menu is unique while running in GPS mode with the standard GPS module compared to running in Conventional mode. All the remaining Job Menu items are covered in the Job Menu description for conventional surveying, starting on Page R-35.
Survey Pro Reference Manual Settings Job Settings. The Settings screen opens several individual screens that control all hardware and software settings. The screens are provided in an index card format. Note: Only the cards that are available when running in GPS Mode with the GPS module are covered in this section. For details on cards shared by both GPS Mode and Conventional Mode, refer to Page R36.
Job Menu – GPS Module Create New Receiver… : opens the Receiver Setup screen where you can set the parameters for communication from data collector to receiver, as well as access the Rx Settings screens where you can configure the receiver settings. When you tap OK, the new receiver is added to your list of known receiver. Activate Selected Receiver: makes the selected receiver the currently active receiver in Survey Pro. Delete:Deletes the selected receiver profile from the list of known receivers.
Survey Pro Reference Manual Note: Some receivers support Bluetooth wireless communication. If the data collector is set to use Bluetooth, then the next two settings are hidden. Baud Rate: the baud rate used for data collector to receiver communications. Parity: the parity used for data collector to receiver communication. Defaults: sets the communication parameters to the default for this brand and model.
Job Menu – GPS Module Rx Settings Job Settings Receiver Receiver Settings… Rx Settings or Job Settings Receiver Create New Receiver… Rx Settings or Connect to Receiver Receiver Settings Rx Settings or Connect to Receiver Create New Receiver Rx Settings or The Rx Settings screen contains three cards to configure the receiver mode, RTK correction type, RTK data modem, satellite tracking elevation cutoff, as well as some settings specific for particular brands and models of receiver.
Survey Pro Reference Manual transfer GPS measurements in real time. This mode is used to setup both static and stop/go post processing receivers. • Ntrip Rover: Select this mode to use the receiver as an RTK rover where the base corrections are to be supplied to the rover by connection to an Ntrip service. To configure an Ntrip rover, you must setup the Windows Networking modem parameters on the Data Modem card.
Job Menu – GPS Module modem you are using is not in the list of known devices, you can choose Generic Serial to set the communication parameters to work with just about any external data modem. Serial Port: displays the current settings for communication between the receiver and the modem. This includes: Baud Rate: displays the baud rate the receiver will use to communicate with the modem. Parity: displays the parity the receiver will use to communicate with the modem.
Survey Pro Reference Manual Edit : Opens the Cell Phone Settings or IP Modem Settings screen (Page R-102 or R-103, respectively) where the selected data modem configuration can be modified. Delete : Deletes the selected data modem configuration. Modem Serial Comms Screen The Modem Serial Comms. screen is used to change the settings for communication between the base or rover receiver and the data modem.
Job Menu – GPS Module Trimble Internal Radio Pac Crest Radio Channel: is where you select the channel the radio will use to communicate with the other radio. Sensitivity: is where you select the sensitivity of the radio. Mode: is where you select the transmit format used by the base radio. The rover radio must be listening for same format the base is broadcasting. Baud: displays the baud rate the radio is currently set to.
Survey Pro Reference Manual Cell Phone Settings Screen The Cell Phone Settings screen is used to create or modify a cell phone data modem configuration. Cell Phone Settings – Base Card Cell Phone Settings – Rover Card Use Advanced Settings (Base Card): When checked, allows you to specify alternate Hayes AT auto answer command. If unchecked, the default AT auto answer command of ate0s0=1 is used. Auto Answer Command: is the alternate Hayes AT command to use for auto answering.
Job Menu – GPS Module IP Modem Settings Screen The IP Modem Settings screen is used to create or modify an IP modem configuration. (You can only configure in IP modem when RTK Rover is selected for the receiver.) IP Address of Base: is the IP address of the base. Port (Socket) of Base: is the socket number of the base. Use Advanced Settings: When checked, allows you to specify alternate Hayes AT commands to connect and disconnect.
Survey Pro Reference Manual Settings for Thales (Ashtech) Receivers // reference Z family documentation available at: ftp://ftp.thalesnavigation.com/Reference%20Manuals/Z-Xtreme/Z family.pdf Canopy: is where you set a parameter to describe the multi-path environment. This command is relevant for ROVER mode or RVP. Choices are: Open Sky (default) Under Canopy (forest, urban canyon) Confidence Level: is where you set the confidence level for ambiguity fixing.
Job Menu – GPS Module • • Medium High Note: It is recommended you set this value to High. This will usually mean the RTK engine may take longer to resolve a fixed position. It might even mean not being able to resolve a fixed solution in some situations. However, the consequence of a lower confidence level is that it makes it more likely to resolve an incorrect fixed ambiguity. The results of using an incorrect fix are usually much worse than the results of using a float solution.
Survey Pro Reference Manual Measure Mode Settings Job Settings Measure Mode. The Measure Mode card is used to configure the RTK data collection settings. Receiver Dynamics: is where you control the receiver dynamics for point occupations. There are two choices • Static on occupy: On starting a point occupation, receiver is put in static mode where it calculates position assuming no motion and applies advanced averaging techniques for the most precise solution.
Job Menu – GPS Module Automatically accept data collection…: is where you select to automatically accept data collection points when the criteria are met. When checked, both the data and Offset Shots screens will automatically accept points once the measurement is better than the specified criteria. Data collection routines will always collect at least 5 seconds worth of data before automatically accepting points based on criteria.
Survey Pro Reference Manual • Do not store: this option will prohibit acceptance of autonomous points in RTK data collection routines. • Prompt for layer: this option will prompt the user whenever an autonomous point is accepted. The layer specified will be the default layer to store autonomous points, but the user can over ride at the prompt. • Store on selected layer: this option will automatically store autonomous points accepted during RTK data collection routines on the specified layer.
Job Menu – Basic GPS This section describes the Settings menu item from the Job Menu for the Basic GPS Module. See Page 93 for a description of the Job Menu for when running in GPS mode with the standard GPS module. Only the Settings menu item in the Job Menu contains screens that are unique to the Basic GPS module. References are given for all the other Settings screens that are documented elsewhere in the manual.
Survey Pro Reference Manual Settings Job Settings. The Settings screen provides access to several individual screens that control all hardware and software settings. The screens are provided in an index card format. Connections Job Settings Connections. The Connections card is used to configure how the data collector will communicate with the base and rover receivers. Current Connection Settings: Displays the current connection settings (Bluetooth or serial) for the base and rover receivers.
Job Menu – Basic GPS Module Change Settings Job Settings Connections Change Settings. The Change Settings screen can be used to quickly switch the base/rover receiver between serial and Bluetooth and access other Bluetooth tools. Windows Bluetooth Settings : Opens the Windows Bluetooth Settings screen where Bluetooth devices can be configured.
Survey Pro Reference Manual Bluetooth Setup Wizard Job Settings Connections Bluetooth Setup Wizard. The Bluetooth Setup Wizard uses a series of screens to walk you through the process of scanning for nearby Bluetooth receivers and configures their connections on the data collector. Any Bluetooth devices in the area that are not valid receivers will not be displayed. If a particular base/rover receiver is not detected, it is automatically configured to use a serial connection.
Job Menu – Basic GPS Module Radio Settings Job Settings Radio Settings. The Radio Settings card is used to configure the base radio when using a local base/radio configuration, or configure a cellular phone as a data modem for Internet base corrections. The choice made from the upper radio buttons determines the remaining options on the screen. Base/Rover Radio RTK: should be selected when using a local base receiver/radio configuration.
Survey Pro Reference Manual information on adding a modem connection, see Using a Cellular Phone in the Basic GPS Module section of the User’s manual. • IP Address of Base: is the IP address of the base, as provided by the Internet service. • Port (Socket) of Base: is the socket number of the base, as provided by the Internet service. Change Radio Settings Screen Job Settings Radio Settings Change Radio Settings.
Job Menu – Basic GPS Module Measure Mode Job Settings Meas. Mode. See Page R-106. Post Process Job Settings Post Process. See Page R-107. Units Job Settings Units. See Page R-41. Format Job Settings Format. See Page R-43. Files Job Settings Files. See Page R-44. Surveying Job Settings Surveying. See Page R-45.
Survey Pro Reference Manual Stakeout Job Settings Stakeout. See Page R-47. Date/Time Job Settings Date/Time. See Page R-54. Buttons Job Settings Buttons. See Page R-55. General Job Settings See Page R-56. R-116 General.
Survey Menu The Survey Menu contains the routines used for collecting data. See Page R-171 for a description of the Survey Menu if running in GPS mode.
Survey Pro Reference Manual Backsight Setup Survey Backsight Setup. The Backsight Setup screen allows you to define your backsight prior to performing data collection or stakeout. The screen is also accessible from any screen that requires a backsight. Note: all the information in the Backsight Setup screen is saved and will automatically be recalled if the job is reopened at a later time, but the screen must still be re-solved before you can begin surveying.
Survey Menu – Conventional Mode Note: The backsight circle angle is subtracted from all horizontal angles that are read during data collection and the resulting points are adjusted accordingly. This is usually only done when surveying in true azimuths. This value can be change from the Backsight Circle or Backsight Solved screens. Current BS Direction: displays the azimuth of the current backsight.
Survey Pro Reference Manual Backsight Solved Survey Backsight Setup Solve…. The Backsight Solved screen is automatically opened after solving the Backsight Setup screen. It is used to send or read the instrument’s circle, optionally confirm the backsight location, and optionally store a new point for the backsight location. Note: The Backsight Solved screen will not open when the Use Classic Backsight Setup checkbox is checked in the Survey Settings screen (Page R-45).
Survey Menu – Conventional Mode Read Circle : Will read the current horizontal angle from the instrument and set that as the backsight circle. (Non-zero backsight circle values are typically used only when surveying in true azimuths.) Check Backsight: Once the backsight has been checked by distance or angle, the symbol will be replaced with a .
Survey Pro Reference Manual Check Backsight Survey Backsight Setup Check…. The Check Backsight screen is used to help confirm that the total station is facing the correct backsight by comparing the known distance or circular angle to the backsight with the measured value. By Distance : will take a shot to a prism located over the backsight point and compare the measured distance with the computed distance between the occupy and backsight points stored in the current job.
Survey Menu – Conventional Mode Check by Angle Results Circle: is the horizontal angle that was measured by the total station. Azimuth: is the known azimuth to the current backsight. Error: is the difference between the two above angles. Backsight Circle Survey Backsight Setup Circle…. The Backsight Circle dialog box is used to modify the horizontal angle read from a total station so that the resulting angle is an azimuth. This routine can also be performed from the Backsight Solved screen.
Survey Pro Reference Manual Traverse / Sideshot Survey Traverse / Sideshot. The Traverse / Sideshot screen is the main screen used for data collection. : is a shortcut to the Surveying Settings screen (Page R-45). Foresight: is the point name that will be used for the next stored point. Description: is the description for the next stored point. HR: is the height of the rod. : opens the Smart Target options (Page R449). Side Shot : will trigger the total station to take a shot to the prism.
Survey Menu – Conventional Mode Note: The current backsight information is displayed across the top of the Traverse / Sideshot screen. Results Angle Right: is the horizontal angle right around the Occupy Point from the Backsight to the Foresight Point. Azimuth: is the azimuth from the Occupy Point to the Foresight Point. Zenith: is the zenith angle measured by the total station to the prism. Slope Dist: is the slope distance measured by the total station to the prism.
Survey Pro Reference Manual Traverse Now or Later? After taking a shot with the Traverse button, the Traverse Now or Later? dialog box will open where you can specify if you want to traverse now or later . Traverse Now : expects you to move your total station to the next occupy point before any additional shots are taken. The occupy, foresight, and backsight points will be updated accordingly.
Survey Menu – Conventional Mode New Occupy Point After traversing to a new point, the New Occupy Point dialog box will open that informs you of the points that have been updated and computes the azimuth to the new backsight. New Backsight Circle: displays the horizontal angle that should be displayed on the total station once it is set up over the New Occupy Point and facing the New Backsight Point.
Survey Pro Reference Manual Point Exists Survey Traverse / Sideshot Traverse or Side Shot. When performing a traverse or side shot and the foresight point name already exists, the Point Exists screen will open where you select how to handle the new point. Overwrite Existing : will overwrite the existing point with the new coordinates. Use Next Available : will store the coordinates using the next available point name.
Survey Menu – Conventional Mode Remote Shot (Remote Mode) Survey Traverse / Sideshot Traverse or Side Shot. When running in remote mode, tapping the Traverse or Side Shot button from the Traverse / Sideshot screen will open the Remote Shot screen, shown here. The Remote Shot screen is identical to the Remote Control screen (Page R-162), except it has an additional button that allows you to trigger the total station to take a shot.
Survey Pro Reference Manual Repetition Shots Survey Repetition Shots. The Repetition Shots screen is used to perform side shots or traverse shots using any number of repetitions. Note: The sequence that the repetition shots are performed is selected in the Repetition Settings screen (Page R-53). : is a shortcut to the Surveying and Repetition Settings screens (Page R-45 and R53 respectively). Foresight: is the name of the point that will be stored.
Survey Menu – Conventional Mode Note: A residual is the difference between a single measurement and the average of all the measurements. Note: If a residual exceeds the tolerances set in the Repetition Settings screen (Page R-53), that value is displayed in bold text. HA , ZA , SD : allows you to replace the current repetition data for the corresponding button with new data. Once tapped, the repetition data for the tapped button will be deleted.
Survey Pro Reference Manual Multiple Sideshots Survey Multiple Sideshots. The Multiple Sideshots screen is used to perform multiple side shots using any number of repetitions to each foresight without the need to re-shoot the backsight. Foresight: is the point name that will be stored. Description: is the description for the next stored point. HR: is the length of the rod. : opens the Smart Target options (Page R449). Number of Sets: is the desired number of sets to shoot to the backsight or foresight.
Survey Menu – Conventional Mode Radial Sideshots Survey Radial Sideshots. The Radial Sideshots routine combines the functionality of the Multiple Sideshots routine with the accuracy of the Repetition Shots routine. It is used to perform repetition shots to a backsight and any number of foresights (side shots) from the same occupy point. The routine consists of multiple screens. Each is customized according to where you are in the routine.
Survey Pro Reference Manual Distance Offset Shot Survey Distance Offset. The Distance Offset screen is used to store a new point that is a known distance away from the rod location. This screen is useful when the rod cannot occupy the new point’s location. : is a shortcut to the Surveying Settings screens (Page R-45). Foresight: is the point name that will be stored. Description: is the description for the offset shot that is stored. HR: is the length of the rod.
Survey Menu – Conventional Mode Horizontal Angle Offset Survey Horizontal Angle Offset. The Horizontal Angle Offset screen allows you to compute and store the location of a new point that cannot be occupied, such as at the center of large tree. The routine shoots a prism positioned at the side of the new point and then reads the horizontal angle when aiming toward the center of the new point to compute the new point’s location. : is a shortcut to the Surveying Settings screen (Page R-45).
Survey Pro Reference Manual Vertical Angle Offset Survey Vertical Angle Offset. The Vertical Angle Offset screen allows you to compute and store the location of a new point that exists directly above or below the rod location, but cannot be occupied, such as the top of a utility pole. The new point will have the same coordinates as the rod location, but with a different elevation. : is a shortcut to the Surveying Settings screen (Page R-45).
Survey Menu – Conventional Mode Auto Collect Survey Auto Collect. The Auto Collect screen allows users with robotic total stations to automatically collect points either at a specified time interval or after the rod has moved a specified horizontal distance. Note: This routine only works when used with a robotic total station in remote control mode. : is a shortcut to the Surveying Settings screen (Page R-45). Foresight: is the point name that will be used when storing the first new point.
Survey Pro Reference Manual Next > : opens the next screen. Auto Collect – Screen Two The second Auto Collect screen displays information related to the points that have been stored and when the next point will be stored. The box in the upper-left corner displays the direction and distance the total station is aiming relative to the backsight. The upper-right corner displays the next store point number and when the next point will be stored in either seconds or distance.
Survey Menu – Conventional Mode Corner & 2 Lines Survey Corner & 2 Lines. The Corner and 2 Lines screen is used to store a point at the corner of a structure using a reflectorless total station where a direct measurement to the point is not possible, but two points on two intersecting lines can be shot. Foresight: is the name of the point that will be stored. Description: is the description for the point that will be stored. 1 Line e2 Lin 1 2 1 Target HR: 0.
Survey Pro Reference Manual Corner & Angle Survey Corner & Angle. The Corner and Angle screen is used to store a point that cannot be shot on a reference line using a reflectorless total station where two other points on the same line can be shot. Foresight: is the name of the point that will be stored. Description: is the description for the point that will be stored. HR: 0.000: shows that no rod height will be used with this routine since all shots are direct reflectorless.
Survey Menu – Conventional Mode Corner & Offset Survey Corner & Offset. The Corner and Offset screen is used to store a point using a reflectorless total station for a point that cannot be shot directly, but the offset(s) to the point can be measured from a reference line that can be shot. Foresight: is the name of the point that will be stored. Description: is the description for the point that will be stored. HR: 0.
Survey Pro Reference Manual Backsight : opens the Backsight Setup screen (Page R-118) where the current backsight can be modified. Note: After each shot is complete, the computed elevation is displayed for the new point. You can either enter a different elevation or tap to accept the computed elevation. Corner & Plane Survey Corner & Plane.
Survey Menu – Conventional Mode Note: After all shots are done, the computed elevation is displayed for the new point. You can either enter a different elevation or tap to accept the computed elevation. Backsight : opens the Backsight Setup screen (Page R-118) where the current backsight can be modified. Surface Scan Survey Surface Scan. The Surface Scan screen takes advantage of a robotic, reflectorless total station to automatically take a sequence of shots of a surface.
Survey Pro Reference Manual Note: If any points defining your perimeter already exist, the point names can be entered in these fields without re-shooting them. Shoot 1 , Shoot 2 , Shoot 3 : Shoots and stores the corresponding point. Horizontal Distance Interval: is the horizontal distance between each shot taken during the surface scan. Vertical Distance Interval: is the vertical distance between each shot taken during the surface scan.
Survey Menu – Conventional Mode Surface Scan Statistics Survey Surface Scan Next >. The Surface Scan Statistics screen displays details about the surface that was just defined. Store Pts: This box should be checked to store the points that are shot during the surface scan. Enter the starting point number in the corresponding field. Back : Returns to the previous screen.
Survey Pro Reference Manual Surface Scan Results Survey Surface Scan Next > Go >. The Surface Scan Results screen contains two cards that detail the progress of the surface scan. The Map card shows the points that were shot in green, points that have not yet been shot in gray and rejected points in red. Stop (Results card): will stop the surface scan. X,Y View / X,Z View (Map card): Changes the orientation of the current view.
Survey Menu – Conventional Mode Video Scan Survey Video Scan. This feature is only available when using a supported total station with a USB or supported radio connection, and only on data collectors running Windows Mobile 5. The Video Scan routine will quickly take several measurements within a predefined area (scan frame). The data is stored to a *.tsf Point Cloud file, which, along with the raw data file, can be read by Trimble RealWorks software to digitally model the surface.
Survey Pro Reference Manual Hatching Tool: fills an existing scan frame with parallel lines to make it stand out visually. Clear Scan Frame Data: clears any scan frame data from the screen. / Scan Frame Toggle: inverts the horizontal limits of an existing rectangular scan frame. This tool can be used to quickly define a 360° scan frame for taking panoramic photos by first creating a rectangular scan frame with the desired height and a near-zero width and then tap this button.
Survey Menu – Conventional Mode Brightness/Contrast: opens a dialog box where the brightness, contrast and white balance can be adjusted. Take Photo: Takes a digital photo and stores the photo to a file. (See Video Settings on Page 167 for details on configuring the settings for this feature.) Take Panoramic Photo: This will take a photograph within the current polygonal or rectangular scan frame. When a large scan frame is defined, multiple photos of the entire area are taken with minimal overlap.
Survey Pro Reference Manual Video Scan Settings Survey Video Scan The Video Scan Settings screen is used to configure how many points to shoot within the scan frame. You have a choice to define the number of points by distance between points, angle between points, total number of points, or the time required to shoot all points. By Distance HD/VD: specifies the horizontal and vertical distances between points that are measured within a scan frame.
Survey Menu – Conventional Mode Shoot From Two Ends Survey Shoot From 2 Ends. The Shoot From 2 Ends screen is used to provide more accurate vertical closure to a traverse. The routine requires that a foresight point is shot, but it is not stored until after it is occupied and another shot is taken to the previous occupy point. The coordinates for the foresight point are computed from an average of data gathered at each occupy point.
Survey Pro Reference Manual Record Mode Survey Record Mode. When running in Record Mode, all control of the total station is performed from the total station’s keypad. The data collector will simply log each shot that is taken from the total station. This routine is typically used for topo work, where the total station remains over a single occupy point during all shots. Note: Not all total stations support record mode. : is a shortcut to the Surveying Settings screen (Page R-45).
Survey Menu – Conventional Mode Resection Survey Resection. The Resection screen allows you to compute an unknown occupied position by shooting two to seven known positions. Store Point: is the name that will be used when the new occupied point is stored. Instrument Height: is the height of the instrument above the ground. Total Resect Points to Shoot: is the number of known positions that will be shot, from 2 to 7.
Survey Pro Reference Manual 449). Take Shot… : Takes a shot to the prism at the specified foresight point. After the last shot is performed, the Save Point dialog box will open, described next. Save Point Once the final shot is completed, the Save Point dialog box will open showing the computed coordinates for the occupy point. Description: is the desired description for the point that will be stored. : stores the new point and automatically sets the point as the current occupy point.
Survey Menu – Conventional Mode Remote Elevation Survey Remote Elevation. The Remote Elevation screen will compute the elevation for the occupy point by shooting a foresight with a known elevation, or it will compute the elevation for a foresight when the occupy elevation is known. Known Elevation Is…: is where you specify if the Occupy point or the Foresight point has a known elevation. Elevation: is the known elevation for the selected point.
Survey Pro Reference Manual Check Point Survey Check Point. The Check Point screen compares the rod location with an existing point in the project. This routine is similar to the Check Backsight routine (Page R-122) and is used to verify that the rod and/or the total station is over the correct point. This routine does not store a new point. Point: is the point from the project that will be compared to the observed point (rod location). Height of Rod: is the length of the rod.
Survey Menu – Conventional Mode Solar Observation Survey Solar Observation. The Solar Observation screen is used to compute the azimuth to an arbitrary backsight based on the position of a celestial body; typically the sun. WARNING! Direct viewing of the sun without a proper filter will cause serious eye damage. Pointing a total station directly toward the sun without a solar filter can also damage the EDM components.
Survey Pro Reference Manual Center. Note: Typically Left Edge of Center is selected when performing a sun shot in the northern hemisphere and Center is selected for star shots. Corrections : displays which corrections are currently selected with an N for no, or a Y for yes. When tapped, the Corrections dialog box opens where the following corrections are configured.
Survey Menu – Conventional Mode Shots Number of sets: is the number of sets that will be taken to the celestial object. Reverse Shots ;: When checked, reverse shots will be required with each set. When unchecked, only direct shots are required. Shoot : opens the Enter Shot Data screen, described below, where the shot data is entered for the selected observation. Toss / Incl : will toggle the selected observation so that it will be hidden or unhidden, respectively.
Survey Pro Reference Manual The Enter Shot Data Dialog Box Horizontal Angle: displays the horizontal angle measured by the total station. This value is updated with the Take Shot button, described below. Current Date / Time: displays the current date, time, and DUT. These settings can be changed from the Date/Time Settings screen (Page R-54). Date: if incorrect, the current date should be entered here. Time: is where the precise time that the observation occurred is entered.
Survey Menu – Conventional Mode be automatically read from the data collector using the Get Local Time button, or measured from an external time piece and manually entered in the appropriate fields. 4. When finished, tap the observation. button to complete the current When all observations are complete, the Results page displays the computed azimuth to the backsight. Results BS D/R: is the horizontal angle recorded to the backsight for the particular direct/reverse observation.
Survey Pro Reference Manual Remote Control Survey Remote Control. Remote control mode is a special mode that makes it easier for users to control fully robotic total stations from a remote data collector. Note: The remote control functions are available only after a supported robotic total station is selected and enabled in the Instrument Settings screen.
Survey Menu – Conventional Mode Lock : puts the total station in track mode where it will track the movements of the prism. Stop : stops the total station from tracking or searching. Turn To : opens the Turn To screen (Page R-163) where the total station can be turned to a specified direction or quickly flipped between face one and face two. EDM Mode: allows you to select from various EDM modes. The options available depend on the total station being used.
Survey Pro Reference Manual The satellite icon in the Command Bar indicates the status of the satellite connection when using GeoLock. Tapping this icon will display a pop-up list with the following items: • Sky Plot: opens the Sky Plot screen. (Page R-169) • Settings: opens the GeoLock Settings screen. (Page R-170) • Reset: Resets the GPS localization solution.
Survey Menu – Conventional Mode Video Card Survey Remote Control Video. This feature is only available when using a supported total station with a USB or supported radio connection, and only on data collectors running Windows Mobile 5. The Video card displays a live video image from the total station and allows you to adjust the camera/video settings, take a photo, or turn the total station. Tapping anywhere within the video image will turn the total station to that location.
Survey Pro Reference Manual Video Display Options Survey Remote Control Video. The Video Display Options screen is used to customize the look of points that are overlaid on the video screen. Show Points: when checked, points will be overlaid on the video screen. The color that fills the small squares that represents the points can be selected with the corresponding color button. When unchecked, no points or point names are overlaid.
Survey Menu – Conventional Mode Video Settings Survey Remote Control Video. or Job Settings Instrument Instrument Settings Video. Video. Instrument Settings…. The Video Settings screen is used to configure the quality of the live video image and stored photos.) Quality: is used to configure the quality of live video image where Fine produces the best image quality, but takes more time for the video image to refresh.
Survey Pro Reference Manual Aim Card Survey Remote Control Aim. The Aim card is used to precisely aim the instrument. Tapping around the total station graphic will turn the instrument to the location corresponding to the horizontal and vertical scale bars. By Angle / By Distance : toggles between turning by angles or by distances, respectively. The scales in the scale bars will also switch between angles or distances. The scales in the scale bars are calculated using the last distance that was measured.
Survey Menu – Conventional Mode Sky Plot (available only when using GeoLock) Survey Remote Control Sky Plot The Sky Plot screen displays the relative location of the visible satellites in the sky, as well as if they are being used to calculate a position. Satellites with a usable signal are shown with red flashing indicators. The Elevation Mask is the minimum angle above the horizon where locked satellites are used for a solution. This area is indicated on the screen by the inner circle.
Survey Pro Reference Manual GeoLock Settings Survey or Job Remote Control Settings Settings GeoLock. The GeoLock Settings screen is used to enable/disable GeoLock and configure the receiver communication settings. Enable GeoLock: When checked, enables the GeoLock feature. Model: Only Generic NMEA can be selected, which works for most GPS receivers that output NMEA data. Serial Port: is the serial port on the data collector used to communicate with the GPS receiver.
Survey Menu – GPS The Survey Menu while running in GPS mode with the GPS module contains the routines used for RTK data collection and post processing data collection. The menu items are the same regardless of the type of data collection. However, some functions, such as Control Points and Remote Elevation, will only allow you to start when connected to an RTK receiver. Other functions, such as Post Processing, will only allow you to start when connected to a post processing receiver.
Survey Pro Reference Manual GPS Status Survey GPS Status. The GPS Status screen contains several index card-format screens providing real time status of the active receiver. Receiver The Receiver card displays information about the receiver mode and GPS solution quality. Mode: displays if the receiver is set to Off, Base, Rover, or Post Processing mode. Memory: displays the amount of memory remaining in the receiver’s internal storage card. Battery: displays the remaining battery charge in the receiver.
Survey Menu – GPS Module • Code: the receiver is calculating a code differential solution (precision is about 1 to 10 meters). • Float: the receiver is calculating a carrier phase differential solution with float ambiguities (precision is typically within 0.1 m to 0.5 m). • Fixed: the receiver is calculating a carrier phase differential solution with fixed ambiguities (precision is typically within 15 mm).
Survey Pro Reference Manual Receiver mode: (see the Receiver Status card, Page R-172.) Modem Reception: displays two values indicating the data modem signal quality. This information is only displayed if the receiver is in rover mode. Signal Latency: displays the age of the differential correction used in the current GPS solution. This value should be one second or less for good RTK solutions. If this value is consistently greater than one second, check the data modem link.
Survey Menu – GPS Module • Recording: a file on the receiver or in the data collector is open and recording GPS raw data. If this receiver monitors sessions, this field will display: session in progress when a session is ongoing. • Not Recording: no file is open and there is no raw data recording. Last Site ID: displays the Site ID of the current session if a session is in progress. If your receiver does not monitor sessions, the Site ID is the last Site ID used by Survey Pro.
Survey Pro Reference Manual Note: If the receiver setup has not yet been performed, the elevation mask will not be displayed. Also, if you have changed the elevation mask setting, and have not yet reconfigured this receiver, the value you see on this display will be the value from the settings, and not the value the receiver is currently using.
Survey Menu – GPS Module Position The Position card displays your current position as well as your course and speed information if you are moving. The Position card will display one of three coordinates: WGS84 latitude, longitude, height; Local latitude, longitude, height; or Grid north, east, elevation. Solution: (see the Receiver card on Page R172.) Latitude/Longitude/Height: or North/ East/ Elevation: displays the location of the receiver. Heading: displays your course over ground if you are moving.
Survey Pro Reference Manual Start GPS Survey Survey Start GPS Survey. The Start GPS Survey wizard is used to complete the setup necessary for any RTK GPS Survey. The Start GPS Survey wizard is opened from the main menu, or any time you try to access data collection or stake out functions. The steps to complete the Start GPS Survey wizard will depend on what you have already done in the job. Each possible screen is shown below.
Survey Menu – GPS Module Choose Projection Mode The Start GPS Survey Choose Projection Mode screen is used to select a horizontal projection mode. This screen shows when you have not yet solved a coordinate system for this job. You can choose one of two projection modes, depending on the requirements for your survey. Use Ground – TDS Localization >: sets the horizontal projection mode to Ground – TDS Localization, and opens the Choose Base Setup screen.
Survey Pro Reference Manual Base Point: displays the current RTK base point configured in Survey Pro. If no base is set, this box instructs you to start with one of the other two options. Use Current Base>: skips the Base Setup screen, and opens the next screen required for survey setup. This could be the Rover Setup screen, the Start GPS Survey – Solve Localization screen, or the Data Collection screen. Set New Base> : opens the Base Setup screen.
Survey Menu – GPS Module Note: The geoid for the mapping plane zone and the ground localization zone is the same. Changes to the geoid for one record will occur in both. Connect To Receiver The Connect to Receiver screen will prompt you to choose and connect to the receiver required for the next step of GPS setup. This screen is always part of the Start GPS Survey wizard. If the next screen is Base Setup, the Connect to Base prompt will display a list of all your RTK base receivers.
Survey Pro Reference Manual This button only shows when the selected receiver is using the Bluetooth port. Connect>: sets the selected instrument as the current active instrument, begins communicating with the device, and opens the next setup screen in the Start GPS Survey wizard. Note: When the current active instrument is Demo Mode, only the Demo Mode receiver will show up in the list.
Survey Menu – GPS Module Note: When this screen is used in one point setup mode, the one job file point is automatically used as the base point and you use this screen to enter antenna height. When this screen is used to configure base position in Survey Pro after remote base setup from the rover, then this screen is used to display the base point name and antenna height received from the data modem link. Antenna: displays antenna setup for this receiver.
Survey Pro Reference Manual Receiver Antenna The Receiver Antenna screen is used to define the parameters of the antenna used with the current receiver. This screen may be opened as the Base Receiver Antenna, Rover Receiver Antenna, or the Post Processing Antenna screen. Antenna Type: is where you select the model of antenna to use. The options available here depend on the current receiver. Measure To: is where you select method for antenna height measurements.
Survey Menu – GPS Module Vertical Offset Slant Offset Phase Center Radius Measurement Point Slant Height Vertical Height Marker Note: When this screen is used by the RTK rover for updates of antenna height during a survey, the Set button will send the new antenna parameters to the receiver as well as updating Survey Pro's settings.
Survey Pro Reference Manual Base Setup Two – SET This final Base Setup screen is used to SET the receiver as an RTK base using the job file point as the reference position, and to configure the base location in Survey Pro. This screen is shown when the base point has measured or computed geodetic coordinates in the job. Base Point: displays the base point name chosen in the previous screen. Latitude: displays the WGS84 latitude of the job file point.
Survey Menu – GPS Module Ellipse Height: is where you enter the WGS84 ellipsoid height for the base point. Note: You can enter latitude in dd.mmsssss format with north positive, or you can enter dd mm ss.ssssss N/S. You can enter longitude in ddd.mmsssssss format with east positive or you can enter ddd mm ss.sssss E/W. Average position for epochs before GET: instructs the receiver to average autonomous positions for this number of epochs before returning. Get Position From Receiver (Rx.
Survey Pro Reference Manual Rover Setup The Rover Setup screen is used to set the RTK rover receiver, and to configure or check the base reference position in Survey Pro. Rover Status: displays the status of the rover setup in Survey Pro. Base set at: displays the current base point. This will be empty if the base is not set. Antenna: displays antenna setup for this receiver.
Survey Menu – GPS Module matching point or prompt you to store a new point. If you are using the base station you have already set with this data collector, then this check serves as error detection. Solve Localization The Solve Localization screen is used to indicate when a horizontal and vertical localization adjustment is required, and to guide you through the steps to collect control points and solve the adjustment.
Survey Pro Reference Manual Data Collection Survey Data Collection. The Data Collection screen is used to collect GPS measurements and store new points in the job. GPS Status: displays the current solution type, the data modem reception quality, the number of satellites used and the horizontal precision computed by the receiver. When this area is tapped, the GPS Status screen (Page R-172) will open. Point: is where you enter the point name for the next point to be stored.
Survey Menu – GPS Module Note: The Topo SS function never puts the receiver in static mode, so the precision of the rapid side shot will be less than a point occupied in static mode. Feature : opens the Feature Collection screen, where various automatic and manual data collection options are available. Offset : opens the Offset Shots screen, where a point can be collected and stored at a specified offset. Point : opens the Occupy Data Points screen (Page R-194), used to occupy and store a new point.
Survey Pro Reference Manual • Manual: prompt once: stores points in the same way as tapping Topo SS from the Data Collection screen, incrementing the point name after each stored point. • Manual: prompt every point: performs the same function as the Manual Prompt Once routine, above, except you are prompted for a new description, layer, and attribute with each point stored. Interval: is where you enter the interval criteria used for continuous collection modes.
Survey Menu – GPS Module Offset Shots Survey Data Collection Offset. The Offset Shots screen is used to collect a point you cannot physically occupy with GPS. You can occupy a nearby point with the GPS rover and then measure the offset distance and direction with tape and compass, or take a shoot with a laser range finder. Offset Point: is the point name of the offset point to be stored. Description: is the description of the offset point to be stored.
Survey Pro Reference Manual ranger finders available on the Job | Settings | Instrument screen when in conventional mode. The active instrument will always return a zenith and slope distance. The active instrument may return a horizontal angle, which will be treated as an azimuth. Note: If your laser range finder has a compass, azimuth returned will be magnetic. Use the Instrument Settings screen to set Magnetic Declination to apply to the angle.
Survey Menu – GPS Module Session Time: displays the total occupation time so far for this measurement. Count Status: displays Measuring when you have current coordinates from the receiver and the screen is updating with the latest measurement. If you are using Epoch Averaging, Averaging is displayed after you tap Store while the number of epochs is averaged in Survey Pro. Suspended is displayed if you are not receiving valid data from the receiver.
Survey Pro Reference Manual Projection : opens the Projection screen (Page R-204). View Points : opens the View Coordinates File screen, where the project points can be examined. Post Process : opens the Receiver Session screen (Page R-202), where you can occupy a point for a post processing only session. This allows you log a session in the post processing file using an existing point name without changing that point record in the job file.
Survey Menu – GPS Module Note: If the Errors are larger than the measurement precision of the instrument, you probably have a problem with your projection solution. Session Time: displays the total occupation time so far for this measurement. Count Status: displays Measuring when you have current coordinates from the receiver and the screen is updating with the latest measurement.
Survey Pro Reference Manual Control Point: is where you select if the current point is to be used for Horizontal control and/or Vertical control by tapping the appropriate checkboxes. Session Time: displays the total occupation time so far for this measurement. Count Status: displays Measuring when you have current coordinates from the receiver and the screen is updating with the latest measurement.
Survey Menu – GPS Module Post Processing Post processing data collection involves two steps. First, you must open a file and begin logging GPS raw data for post processing. Second, you must measure the antenna height and enter the antenna and station ID for each point you occupy. Post Processing Survey Post Processing The Post Processing screen is used to open or close a post processing data file, and start or stop logging GPS raw data measurements to the file.
Survey Pro Reference Manual Start Stop/Go: use this setting if you want to start a log file in stop and go mode, where the receiver will rove around. In stop and go mode, the GPS raw data is continuously logged to the file to maintain the initialization while roving around, this is the go part. Then, static sessions are marked when the receiver is stationary over a point, this is the stop part. Recording Settings: this area displays values from the Job | Settings | Post Processing screen.
Survey Menu – GPS Module Note: The Post Processing screen is used to start logging with post processing receiver types only. If you wish to record post processing data simultaneous with RTK, then you should set the recording interval on the Job | Settings | Post Process screen and then start the base and rover using the Start GPS Survey wizard. When you tap the Post Processing menu while connected to either the RTK base or rover, you have only two options.
Survey Pro Reference Manual Static / RTK Rover Receiver Session Survey Data Collection -or- Survey Post Processing Survey Control Points Survey Data Collection Start Recording. -orPost Process -orPost Process. The Receiver Session screen is used to enter the station information and antenna height for a post processing data collection session. Starting a Static Session During timed stop and go session Store point in: is used to select how to store this session.
Survey Menu – GPS Module Note: If you are storing this point in Survey Pro, the screen will look like the picture above, and you can pick points using the Survey Pro compound point control. If you choose an existing point, you will be prompted to rename or overwrite, just like RTK data collection. If you are storing this point in the receiver file only, then the point control is replaced with a simple edit box.
Survey Pro Reference Manual Base Setup Survey Base Setup. The Current GPS Base screen displays the position of the current RTK base reference position used by Survey Pro. It can be used to open the Base Setup wizard, which can set an RTK base receiver to begin broadcasting differential corrections, and configure the base reference position in Survey Pro When you tap the Base Setup menu item, the Current GPS Base Station information screen is displayed.
Survey Menu – GPS Module Rover Setup Survey Rover Setup. The Rover Setup screen is used to set an RTK rover to begin receiving differential corrections and to configure or check the base reference position in Survey Pro. The Rover Setup screen is described as part of the Start GPS Survey wizard. Projection Survey Projection.
Survey Pro Reference Manual Projection – TDS Localization Mode The Projection screen is described below for when the horizontal projection mode is set to TDS Localization. Use this setting when you want ground level coordinates, and there is no projection and no datum to define a geodetic coordinate transformation. In this mode, a default map projection is created with your first RTK base setup. You collect GPS measurement on points with known local coordinates, and solve a Localization adjustment.
Survey Menu – GPS Module Projection Details Survey Projection Show Details…. Save System To Database : will save the current projection record to a coordinate system database file. First, the current database file is checked for a matching record, and if found you will be prompted that you need not save the current coordinate system. If no matching record is found, then the current coordinate system will be saved as a new record.
Survey Pro Reference Manual Origin Height / Origin Scale : is where you enter either the height or the scale factor used to reference the localization system to ground level. Same as Base : updates the values with the coordinate and set up group of the GPS base station. Use Geoid: is where you choose to use a geoid model with this zone. When this box is checked, you can select a geoid model from the dropdown list to use with the coordinate system.
Survey Menu – GPS Module Select Coordinate System Survey Projection Reset Origin… Pick from Database. The Select Coordinate System screen is used to pick a Ground – TDS Localization mode default zone or solved localization site from the database file. This screen is described in detail in the Mapping Plane mode projection section on Page R-220. The difference when in Ground – TDS Localization mode is that you can only select records from the TDS Localization Region collection.
Survey Pro Reference Manual Solve Localization Survey Projection Solve Localization…. The Solve Localization wizard is used to solve a horizontal and vertical adjustment for a coordinate system. The user interface and procedure to solve a localization in Ground – TDS Localization mode and Mapping Plane mode are very similar. This section explains how to solve a horizontal and vertical adjustment in either projection mode.
Survey Menu – GPS Module Fix scale to 1.0: check the Solve Rotation Only control to constrain the least squares solution to a scale of 1.0. Do this when you want to orient your GPS to an existing grid but you want to hold the scale of the GPS measurements. Note: You must choose exactly two horizontal control points for a fixed scale localization. Solve H: check Solve H to use the selected control points in a least squares solution or to use the horizontal values from the manual entry card.
Survey Pro Reference Manual Solve Localization – Residuals The Solve Localization Residuals screen is used to display the residuals from the least squares solution, and to change your control point selections and re-solve the adjustment if desired. Solutions: The box for horizontal and vertical solution will display the root mean squared results. If the solution is from a least squares calculation with residuals, the RMS values are from the residuals of each point used in the calculation.
Survey Menu – GPS Module Solve Localization – Manual Parameters The Solve Localization Manual Parameters screen is used to input localization horizontal and vertical parameters by hand. This can be done to copy a localization solution between data collectors in the field, or to recreate a localization solution from a raw data printout. Horizontal Card The Horizontal card is used to manually enter the six parameters of the horizontal localization solution. Scale: is where you enter the scale factor.
Survey Pro Reference Manual Localization Calculator This sub section describes a feature available only in Ground – TDS Localization mode. The Localization Calculator is used to enter the horizontal localization parameters using the pre-Survey Pro 3.5 procedure. Scale: is where you enter the scale factor used to transform distances on the localization mapping plane to your project coordinate system. Note: Using versions of Survey Pro after 3.5, the localization scale should be very close to 1.0.
Survey Menu – GPS Module Localization Calculator – Scale Note: This function is no longer necessary with Survey Pro versions after 3.5. The new localization solution sets the origin scale of the reference stereographic mapping plane based on ground height. This screen was left in to explain scale factor to users who previously used this work flow. Use 1.0 Scale : returns to the Localization Calculator screen with a scale factor of 1.0.
Survey Pro Reference Manual Solve Localization – Results The Solve Localization Results screen is used to display the results of the horizontal and vertical adjustment, and how the adjustment was derived. Horizontal Card The Horizontal card shows results of the horizontal localization solution. Status: displays the status of the current horizontal solution. This will be one of the following: • Control points solution: is displayed when the parameters were calculated from the selected control points.
Survey Menu – GPS Module Vertical Card The Vertical card shows results of the vertical localization solution. Status: displays the status of the current vertical solution. This will be one of the following: • Control points solution: is displayed when the parameters were calculated from the selected control points. • Current vertical site: is displayed when there is a vertical solution and Solve V was not selected on this pass.
Survey Pro Reference Manual Projection – Mapping Plane Mode The Projection screen is described below for when the horizontal projection mode is set to Mapping Plane. Use this setting when you want your coordinate system to be a conformal map projection chosen from the coordinate system database file. See Page R-206 for when the projection mode is set to TDS Localization. Status Line: The text at the top of the screen describes the status of the horizontal projection solution.
Survey Menu – GPS Module Select Coordinate System Survey Projection Select Zone…. The Select Coordinate System screen is used to choose a mapping plane zone or localized site from the coordinate system database file. You can also open the Key In Zone wizard to create a new zone and datum with user specified parameters. Select Mapping Plane Zone Select Mapping Plane Site Database: is where you select what type of coordinate system record to choose.
Survey Pro Reference Manual Use Geoid: is where you choose to use a geoid model with this zone. You can pick a geoid model from the database using the drop down box. Select Database : opens the Select Database screen where you select the coordinate system database to use. Delete Zone : Deletes the currently selected site or zone. Note: This delete function cannot be undone. Also, you cannot delete system database records.
Survey Menu – GPS Module Key in Zone Survey Projection Select Zone… Key in Zone >. Key In Zone - Setup The Key In Zone Setup screen is used to pick the zone and datum type for the new zone, as well as set the azimuth orientation and grid direction for the new zone. Zone Type: is where you select what kind of map projection to use for the new zone. You can choose: • Transverse Mercator.
Survey Pro Reference Manual • North/East Grid: is where you set the coordinates increasing positive in the north, east direction • South/West Grid: is where you set the coordinates increasing positive in the south, west direction. Key In Zone - Mapping Plane Parameters The Key In Zone Mapping Plane Parameters screen is used to enter the values for the map projection zone. The parameters required depend on the zone type.
Survey Menu – GPS Module • Center of Projection Rectify Coordinates: is where you set if the coordinates are rectified. Coordinates are ‘rectified’ if the local plane is rotated by the azimuth angle of the central meridian of the projection so that grid North lines up with geodetic north at the origin. Key In Zone - Ellipse The Key In Zone Ellipse screen is used to set or create an ellipse for a new datum. This screen is only displayed when Datum Type is Molodensky or Similarity.
Survey Pro Reference Manual Key In Zone - Datum Translation The Key In Zone Datum Translation screen is used to enter translations when the Datum Type is Molodensky or Similarity. Datum Translate From WGS84 To Local: is where you enter the three translations from WGS84 to the local datum. Note: The sign convention for the datum translations is from WGS84 to the local datum. If your datum transformation is defined for local to WGS84, be sure to inverse values before entering in Survey Pro.
Survey Menu – GPS Module Key In Zone - Datum from Database The Key In Zone Datum from Database screen is used to select a database datum when the Datum Type is Pick from Data Base. Datum: is where you select the data base datum to use for the new zone. Key In Zone - Results The Key In Zone Results screen is used to review the values you input for the zone to be created.
Survey Pro Reference Manual Ground Coordinates Survey Projection Mapping Plane Ground…. The Ground Coordinates screen is used to toggle between grid and ground coordinates, and to select how to define the origin of the ground coordinate system. Projection Definition: is where you choose how to represent the mapping plane coordinates. There are two options: • Use Grid Coordinates: WGS84 geodetic coordinates will be transformed into mapping plane zone coordinates.
Survey Menu – GPS Module Ground Coordinates - Key In Origin Survey Projection Mapping Plane Ground… Next >. The Ground Coordinates Key In Origin screen is used to input the location of the ground coordinates origin. This screen is used when you select Key in coordinates to define origin on the Setup screen. Project Location: is where you enter the local point from which the ground coordinate scale factor is to be applied. Coordinate Type: is where you select the type of coordinates to enter.
Survey Pro Reference Manual enable the scale factor edit field and enter any other scale factor. Ground Coordinates - Location The Ground Coordinates Location screen is used to define the local ground coordinate of the origin point. This coordinate will be used to calculate an offset from the mapping plane grid coordinates so that you can separate the grid and ground coordinates to make them recognizable.
Survey Menu – GPS Module Remote Elevation Survey Remote Elevation. The Remote Elevation screen is used to compute and store a new base point elevation and vertical site by occupying a known vertical benchmark at the rover. Note: The Remote Elevation screen is only available when a geoid model is used for the vertical projection, the horizontal projection is already solved and the base and rover are set. Base Point: displays the current base point number and elevation details.
Survey Pro Reference Manual Projection wizard to update all job file points, including the base point, with the latest vertical solution. Occupy Benchmark : opens the Occupy Control Point screen (Page R197) where the measurement is taken by the rover on the remote benchmark. The New Elevation field of the Remote Elevation screen will then display the calculated elevation for the base point to be set on tapping Accept.
Survey Menu – GPS Module Import GPS Control Survey Import GPS Control. The Import GPS Control wizard is used to merge an accurate NEE location (control point source) with a GPS collected point in the job file. This point will then be designated as a GPS control point and can be used to solve a localization adjustment. Solving the localization adjustment can be done automatically at the end of this wizard, manually after the end of this wizard, or at a later time.
Survey Pro Reference Manual Enter Control Coordinate – OPUS or NGS Data Sheet The purpose of this screen is to pick a data sheet point or OPUS solution file to use as the control point source. This is the second screen that appears when either OPUS Solution or NGS Data Sheet was selected in the first screen. Point: displays the name of the selected job point that the control point source will be merged into.
Survey Menu – GPS Module Coordinate Type: is where you select the type of coordinates being entered (Grid, Local LLH, or WGS84 LLH). The selection made here determines the format for the following three fields. Latitude / North: The Latitude / Northing of the control point source. Longitude / East: The Longitude / Easting of the control point source. Height / Elevation: The Height / Elevation of the control point source.
Survey Pro Reference Manual cleared for the point and the previous screen is open. If No, we leave the control point source and go back to the selection screen. Finish : See the section on Finish below. Multiple Point Results This screen displays the values to be used to create the new GPS control points. New GPS Control Points to be Created: For all of the selected points, this list box shows the new NEE location, the existing LLH location, and the existing NEE location.
Survey Menu – GPS Module Receiver Information Survey Receiver Info. The Receiver Information screen is used to display the serial number and firmware version of the current receiver. Also, different receivers will return additional information in this window including channel or option version installed. Receiver Type: displays the manufacturer of the receiver currently connected to the data collector. Serial Number: displays the serial number of the current receiver.
Survey Pro Reference Manual Adjust with Projection Survey Adjust with Proj.. The Adjust with Projection wizard is used in three different cases. It is automatically opened to update job file points any time you change the coordinate system site, such as solving a localization adjustment or switching from grid to ground.
Survey Menu – GPS Module temporary WGS84 geodetic location using the source coordinate system, and then into a new plane location using the destination coordinate system. Points with a geodetic location will be transformed into a new plane location using the destination coordinate system. • Adjust only geodetic points: only points with geodetic locations will be adjusted. All eligible points with geodetic locations will be transformed into a new plane location using the destination coordinate system.
Survey Pro Reference Manual Adjust with Projection – Select Source Coordinate System The Adjust with Projection Select Source Coordinate System screen is used to select the coordinate system of the current job file points. When the adjustment mode is Readjust with Current Projection, this screen shows the current coordinate system record details. This screen only shows when the wizard is opened from the menu.
Survey Menu – GPS Module Adjust with Projection – Select Destination Coordinate System The Adjust with Projection Select Destination Coordinate System screen is used to select the coordinate system to transform the job file points into. The interface is identical to the Select Source Coordinate System screen described above. This screen only shows when the adjustment mode is set to Adjust From Source to Destination.
Survey Pro Reference Manual Adjust All Points: use this setting when you want to adjust all points. The method used to adjust plane and geodetic points is described on the Select Points page. Adjust only points with geodetic coordinates: use this setting when you want to update only geodetic points. The method used to adjust geodetic points is described on the Select Points page. Note: The display of these controls will vary depending on the difference between the old and new coordinate system.
Survey Menu – GPS Module Apply : applies the adjustment to the listed points. Note: When the Adjust with Projection wizard was opened from the menu, tapping Apply will only update the selected job file point locations. The job file coordinate system will not be changed in this case. When the Adjust with Projection wizard was opened automatically as a result of a change of coordinate system, tapping Apply will update all eligible job file point locations, and it will update the job file coordinate system.
Survey Pro Reference Manual Projection Calculator – Rotation Convergence: displays the computed rotation from geodetic north to grid north. Rotation: displays the computed rotation from grid north to geodetic north. < Back : returns you to the first Projection Calculator screen. Accept : copies the two computed values to past results and returns you to the first Projection Calculator screen.
Survey Menu – GPS Module Inverse Combined Factor: displays the inverse of the Combined Scale Factor. This is the grid to ground scale factor and is the value used in the localization solution. < Back : returns you to the previous Projection Calculator screen. Accept : copies the two computed values to past results and returns you to the Main Menu. File Management Survey File Management. The File Management routine is used to manage post processing files on a supported GPS receiver.
Survey Pro Reference Manual Note: If a file being downloaded already exists on the data collector, you can overwrite the existing file, give the downloaded file a new name, or cancel the transfer. If you choose to give the file a new name, you must also provide the same *.T00 or *.T01 extension as in the original name. Note: Downloaded files can be transferred to a PC with ActiveSync and then converted to a *.DAT file for use with Trimble Geomatics Office (TGO). To convert a *.T00 or *.T01 file to a *.
Survey Menu – Basic GPS The Survey Menu while running in GPS mode with the Basic GPS module contains the routines used for RTK data collection and post processing data collection. The menu items are the same regardless of the type of data collection. However, some functions, such as Control Points and Remote Elevation will only allow you to start when connected to an RTK receiver. The Data Collection function will behave differently based on the receiver type that is active.
Survey Pro Reference Manual GPS Status Survey GPS Status. The GPS Status screens are described starting on Page 172. Start GPS Survey Survey Start GPS Survey. The Start GPS Survey wizard is used to complete the setup necessary for any RTK GPS Survey. It is opened from the main menu, or any time you try to access data collection or stake out functions. The steps to complete the Start GPS Survey wizard will depend on what you have already done in the job.
Survey Menu – Basic GPS Module Base/Rover Receiver: displays information about the status of the receiver. Measured To: specifies the location on the antenna or receiver where the antenna height should be measured to. Measured: The distance from the ground to the Measured To location. Serial #: is the serial number of the antenna. This information is optional and written as a note in the raw data.
Survey Pro Reference Manual Start Survey – More than One Matching Base Point This screen will open when the base is set up on a point that potentially matches more than one point in the job. Change > : opens the Start Survey – No Matching Base screen (Page R-248) where the base point can be redefined before continuing. Select a Base Point: allows you to choose a point from the dropdown list, which contains all the matching points found in the job. Next > : opens the Set Up Rover screen.
Survey Menu – Basic GPS Module GPS Backsight/Resection GPS Backsight GPS Resection The GPS Backsight/Resection screen will open any time the coordinate system is not solved. It will have one of two states depending on if the base was set up on an existing job point and one additional control point is needed to orient the setup, or the base was set up on a new point from an autonomous setup. Occupy Control > : opens the Occupy Control Setup screen, described below.
Survey Pro Reference Manual Occupy Control Setup The Occupy Control Setup screen is used to specify which job point with accurate NEE coordinates you are occupying and if you want to use the point for horizontal and/or vertical control when localizing (this can be changed later). Point: is the existing job point you are occupying. H: Check this if the point has good horizontal coordinates to use for horizontal control when localizing.
Survey Menu – Basic GPS Module points will be set in the job file, and the projection readjust mechanism will run to update any job points as required. You must remember that the solution has not been checked for quality. Solve Localization Before the Solve Localization wizard starts, the localization is computed using all the control points, and then the automatic blunder detection routine runs to detect low quality control points.
Survey Pro Reference Manual show the root mean squared (RMS) error of the horizontal and vertical solution. • Yellow Warning Triangle: If the localization solved and no blunders were detected, but some of the points used have a large residual error, you will see a yellow triangle and the status line will show the point with the largest horizontal and/or vertical residual.
Survey Menu – Basic GPS Module Data Collection Survey Data Collection. The Data Collection screen is used to collect GPS measurements and store new points in the job. GPS Status (at top of screen): displays the current solution type, the data modem reception quality, the number of satellites used and the horizontal precision computed by the receiver. When this area is tapped, the GPS Status screen will open (Page R-172). Point: is where you enter the point name for the next point to be stored.
Survey Pro Reference Manual Feature : opens the Feature Collection screen (Page R-191), where various automatic and manual data collection options are available. Offset : opens the Offset Shots screen (Page R-193), where a point can be collected and stored at a specified offset. Point : opens the Occupy Data Points screen (Page R-194), used to occupy and store a new point. Traverse Base Survey Data Collection Traverse….
Survey Menu – Basic GPS Module Check Control Point Screen Survey Control Points Data Collection Control Check Point. or Check Point. The Check Control Point screen is used to check a control point. This is done when you want to verify the quality of the coordinate system solution and is described on Page R-196. Occupy Control Point Screen Survey Control Points Data Collection Control Control. or Control. The Occupy Control Point screen is used to add geodetic coordinates to a known project point.
Survey Pro Reference Manual between mapping plane and localization mode. The buttons available will vary depending on the current projection mode. This screen and the screens accessed from it are nearly the same as those found in the GPS module, which are described on Pages R-205 to R-228. The Solve Localization screens vary slightly and are described on Page 251. Receiver Information Survey Receiver Info.
Leveling Menu The Leveling Menu replaces the Survey Menu when running in leveling mode. It contains routines to perform a level loop or 2-peg test.
Survey Pro Reference Manual Select/Create Loop Leveling Select/Create Loop. The Select/Create Loop screen is used to select a loop that has not yet been closed, view the notes for any existing loop, or create a new level loop. Select an Existing Loop: allows you to select an existing loop from the dropdown list. Activate Selected Loop : opens the selected loop so new data can be added to it. (This button will not be available when a closed loop is selected.
Level Menu New Level Loop – Screen Two Desc: is where you can enter an optional description for the new loop. < Back : returns to the previous screen. Create Loop : creates the new loop. Level Notes Leveling Level or Leveling Notes. Select/Create Loop View Level Notes for Selected Loop. The Level Notes screen shows the details of every shot taken for the current loop. If the loop was closed, additional closure details are also provided.
Survey Pro Reference Manual Level Notes Settings Leveling Level Notes The Level Notes Settings screen is used to customize what and how the information in the Level Notes screen is displayed. ; Station/Point Name: displays the Station column where the name of each point and the number of each turning point shot is listed. This column cannot be turned off. ; BS(+): is the column that lists all the backsight readings. This column cannot be turned off.
Level Menu points are not stored in the job and therefore do not have descriptions.) Column Width: When ; Auto Resize is checked, the column widths are automatically sized so the content of each column is visible. Style: When set to ~ Compact, the backsight data for a particular setup is displayed on the same row as the foresight data from the previous setup. When set to ~ Double Spaced, the data for each backsight and foresight shot are displayed in separate rows.
Survey Pro Reference Manual Leveling Shots Leveling Level Turn to Turning Point…. (This screen is also accessed when taking shots for any other observation type.) The Leveling Shots screen is used to perform the required shots to whichever observation you are shooting. The specific shots you are prompted for depends on the observation type, the number of sets, and the shooting sequence. You will only be prompted to shoot a backsight while shooting the first observation from any given setup.
Level Menu Leveling Shot Results The Shot Results screen opens when you are finished taking the shot necessary shots for a particular observation. Toss : will delete the shot data from the corresponding set of shots that has the worst residual. Each consecutive tap of this button will delete the next shot with the worst residual until all the sets are eventually deleted. BS… : allows you to shoot additional shots to the backsight.
Survey Pro Reference Manual Leveling Side Shot Leveling Level Sideshot >. The Leveling Sideshot screen is used to describe a leveling side shot before taking the necessary shots to record it. SS Point: is the name for the new point. Desc: is an optional description for the new point. Default Location for New Points: is where you specify the northing and easting to use when the new point is stored since the leveling procedure cannot compute these.
Level Menu Leveling Stakeout Leveling Level Stakeout >. The Leveling Stakeout screen is used to measure the elevation at an existing point and compute a cut/fill value. Stk Point: is the point in the current job that you want to shoot to determine the cut/fill value. (The location for this point must be known in advance since the leveling routine cannot compute horizontal coordinates.) Backsight Point: Lists the details for the current backsight.
Survey Pro Reference Manual Turn to Benchmark Leveling Level Turn to Benchmark. The Turn to Benchmark screen is used to take a shot at a known benchmark. When shooting a benchmark that will not be used as the closing benchmark, the procedure is identical to shooting a leveling side shot with the exception that this benchmark will be the backsight in the next setup. BM Point: is the point name for the benchmark.
Level Menu Point Exists The Point Exists screen will appear after shooting a benchmark that is already stored in the current job and is used to overwrite the point, create a new point, or access the Close Loop screen to close the loop. Overwrite : Allows you to overwrite the coordinates of the benchmark with the new coordinates. This option will not be available when the benchmark entered in the Turn to Benchmark screen was the same as the starting benchmark.
Survey Pro Reference Manual 2 Peg Test Leveling 2 Peg Test. The 2 Peg Test screen is used to check that the line of sight through the level is horizontal when the bubble is properly centered. The graphic of this screen shows the current setup and indicates which shot you will be shooting next with a red square. The first line of text also indicates which shot must be taken next. Check H. Dist : This button appears after shooting the initial shots to Point A.
Level Menu to take next. The term A1 means to shoot the rod over Point A for Set 1. If the box showed B3, it would mean to shoot the rod over Point B for Set 3. Take Shot : takes the shot indicated within the box on this screen. Peg Test Results The Peg Test Results screen appears after all the required shots are performed for a peg test. The screen lists the details for all the shots taken and the computed error. All the shots taken and the error are recorded only in the raw data file.
Survey Pro Reference Manual them, so setups that are farther apart will carry a larger portion of the error adjustment than the setups that are closer together. Adjust Affected Sideshot Points: When checked, any side shots will be adjusted by the same amount as the setup that was occupied when the side shots were performed. Adjust Loop From Begin To End: This option includes every setup of the selected level loop in the error adjustment.
Level Menu Adjust : Performs the adjustment and opens a screen that details the results. Note: If the selected loop has already been adjusted or if the computed error is negligible, the Adjust button will be inactive. Leveling Remote Control Leveling Remote Control. The Remote Control screen can only be accessed in leveling mode when trigonometric leveling with a robotic total station. The Remote Control screen is described on Page R-162.
Stakeout Menu The Stakeout Menu contains a variety of stakeout routines, including offset staking. See Page R-333 for a description of the Stakeout Menu if running in GPS mode.
Survey Pro Reference Manual Stake Points Stakeout Stake Points. The Stake Points screen allows you to stake a single point or a series of points. : opens the Stakeout Settings screen (Page R47). Design Point: is the name of the first point that you want to stake. Increment: when advancing to the next point, the point number is incremented by the value entered here. (A negative integer can be entered to have point numbers advance in descending order.
Stakeout Menu Stake Points – Screen Two Design point: displays the name of the design point that was entered in the first screen. Description: displays the description assigned to the design point. Angle Right: is the horizontal angle to turn to face the design point. Horz. distance: is the horizontal distance from the occupy point to the design point. Vert Distance: is the vertical distance from the occupy point to the design point.
Survey Pro Reference Manual 4. The dialog shown here will be displayed the first time Circle Zero is used during a stakeout session to warn that the original backsight reference will be lost. Note: The Circle Zero button is not available when using a robotic total station. < Back : returns to the first screen. Stake > : opens the third and final Stake Points screen where the shots to the stake point are performed. Stake Points – Screen Three Height of Rod: is the length of the rod.
Stakeout Menu Change… : is used to modify the current design elevation, which will also modify the associated CUT/FILL value for the current station being staked. Shot : takes a shot to the prism and computes come/go, cut/fill information. Shot data: displays the measurements from the last shot. Store… : stores the stake point. Store/Tape… : opens the Stake Out Point (Tape Offset) dialog box (Page R-309), where the staked point can be stored that includes a specified offset.
Survey Pro Reference Manual Instrument Stakeout Stakeout Stake Points Solve > Stake >. Instrument Stakeout is a special stakeout option only available when using a Nikon DTM or NPL series total station while the Send Stakeout Data to Instrument option is checked in the Instrument Settings screen. When using Instrument Stakeout, a new stakeout screen, shown below, will appear after you tap Stake > from the Stake Points Screen Two, described above.
Stakeout Menu Remote Staking Stakeout Stake Points Solve > Stake >. Performing stake out in remote mode is different from running in a non-remote mode because the feedback is continuous and provided in the rod’s point of view instead of the total station’s point of view. When staking in remote mode, the first four shots taken in a row where no distance is returned will result in a beep to warn that the instrument has possibly lost track of the prism.
Survey Pro Reference Manual Stake List of Points Screen Stakeout Stake List of Points. . The Stake List of Points screen is used to stake points from a specified list of points. Points can also be selected by description or polyline. : opens the Stakeout Settings screen (Page R47). Tap Points… : displays a map of the current job. Simply tap the points that you want to stake and then tap . To/From… : Opens the Point List screen (Page R-443) where a point list can be created.
Stakeout Menu Solve > : opens the next Stake List of Points screen where the current Design Point can be staked. Note: The screens available after tapping Solve > or Next Point > are identical to Screens Two and Three in the Stake Points routine and are described on pages R-275 through R-276. Edit Point List Stakeout Stake List of Points Stakeout Stake List of Points Change or Edit List… The Edit Point List screen is used to modify the existing point list.
Survey Pro Reference Manual Stake to Line Stakeout Stake to Line. . The Stake to Line screen allows you to locate any location in relation to a predefined line. The line can be defined by two points, a point and direction, a polyline or the centerline of an alignment. Distance, direction and cut/fill information is provided so the rod can locate the line by traveling the shortest possible distance (a perpendicular offset to the line).
Stakeout Menu Stake to Line – Screen Two The second screen is where the staking is performed. The graphic display of this screen will change depending on how close the rod is to the specified line. The initial screen that is displayed before a shot is performed shows the position of the total station, the line of the backsight and the specified line to stake. Each type of graphic is displayed below. HR: is the rod length. EDM: This button can be toggled to shoot in various EDM modes.
Survey Pro Reference Manual Graphic when prism is greater than 10-feet from the line. Graphic when prism is between 1-foot and 10-feet from the line. Graphic when prism is within 1-foot of the line Graphic when prism is on the line or within the Horizontal Distance Tolerance specified in the Stakeout Settings screen (Page R-47). Cut / Fill: displays the required amount of cut or fill to bring the stake point to the elevation of the reference line at the nearest perpendicular.
Stakeout Menu Remote Stake to Line The contents of the Stake to Line screen when running in remote mode is nearly identical to running in non-remote mode, except the graphic portion of the screen looks and behaves differently. Point the data collector toward the total station for proper orientation and the graphic tells you the direction to travel to reach the line in the shortest distance.
Survey Pro Reference Manual Offset Staking Stakeout Offset Staking. The Offset Staking screen is used to stake the center of a road, the road edge, the curb/ditch edge, or any offset at fixed intervals. An existing polyline, alignment, or a specified point range can define the centerline of the road. The first Offset Staking screen is used to define the centerline of the road that you want to offset stake. Tap Line… : displays a map of all the polylines and alignments in the current job.
Stakeout Menu Offset Staking – Screen Two The second Offset Staking screen is used to define the cross section of the road that you want to offset stake. 1/2 Road Width: is the Left and Right width of the road, respectively, from the centerline to the edge of payment. (See diagram below.) X-Slope (%): is the Left and Right slope of the road, respectively, from the centerline to the edge of payment. Note: A negative slope will result in water running from the centerline toward the edge of payment.
Survey Pro Reference Manual Note: The specified curb or ditch height and offset will be applied to both sides of the road. < Back : returns to the previous screen. Next > : opens the next screen. Offset Staking – Screen Three The third Offset Staking screen is used to select the station and section of the road to be staked and to specify an offset distance from the design point. Stake Station: is the station to be staked. HR: is the rod height.
Stakeout Menu occurring below the selected node. Negative values result in the stake location occurring above the selected node. X-Slope (%): is the slope of the selected road section. 1/2 Road Width: displays the width of the selected road section defined in the previous screen. This value can quickly be edited from this field. : opens the Smart Target options (Page R-449). Backsight… : opens the Backsight Setup screen (Page R-118). < Back : returns to the previous screen. Solve > : opens the next screen.
Survey Pro Reference Manual 1. A new backsight circle value is computed, sent to the instrument and stored in the raw data 2. The Angle Right value is changed to zero to reflect the change. The instrument now needs to be turned horizontally to zero to face the current target location. 3. To prevent errors if this button is used, the backsight set up is invalidated when exiting the Stakeout dialog. A circle zeroed on a design point is meaningless once the design point has been staked.
Stakeout Menu Rod Elev: displays the elevation at the rod’s location computed from the last shot. Change… : is used to modify the current design elevation, which will also modify the associated CUT/FILL value for the current station being staked. Shot : takes a shot to the prism and computes come/go, cut/fill information. Shot data: displays the measurements from the last shot. Store… : opens the next screen.
Survey Pro Reference Manual Offset Staking – Screen Six This screen is used to describe the stake point before it is stored and select if the Results screen should be displayed (described next). Point: is the point name for the stake point being stored. Description: is the description for the stake point being stored. The default description is the station, side, and distance from the centerline for the design point.
Stakeout Menu Slope Staking Stakeout Slope Staking. The Slope Staking screen is used to locate the catch points for a roadway in any terrain. The first screen is used to define or select the line that describes the centerline of the road to be slope staked. An existing polyline or alignment can be selected, or a series of existing points can be entered to define the centerline. Tap Line… : allows you to tap an existing polyline or alignment that defines the centerline of the road.
Survey Pro Reference Manual cause water to run from the centerline toward the edge.) ; Stake Curb / Ditch: When checked, this allows you to include a curb or ditch in the road profile. Height: defines the height of the curb, or depth of the ditch. (A negative value would be used to define the depth of a ditch.) Offset From Edge of Road: defines the width of the curb or ditch. < Back : returns to the previous screen. Next > : opens the next screen.
Stakeout Menu where a ditch meets an area requiring a fill, which would otherwise result in an area with two similar or identical negative slopes. < Back : returns to the previous screen. Stake CP > : opens the next screen. Slope Staking – Screen Four The fourth screen is used to perform the actual slope staking shots. Height of Rod: is the rod height. EDM: This button can be toggled to shoot in various EDM modes. The options available depend on the total station being used.
Survey Pro Reference Manual Note: The Vertical Map will show an X at the location of each previous shot. This can be useful in determining if the current terrain will never intersect the slope (no catch point). • Horizontal Map : displays an overhead view of the job. • Shot Data : displays the shot data for the latest shot. Left / Right: displays if a Cut or Fill slope is being computed and if it is on the Left or Right side of the road, respectively.
Stakeout Menu < Back : returns to the previous screen. Store > : opens the next screen. Slope Staking – Screen Five The fifth screen is used to store a point for the last shot taken from the previous screen, which should be located at the catch point. Point Name: is the name assigned to the stored point. Description: is the description assigned to the stored point. Store CP : stores the point.
Survey Pro Reference Manual Slope Staking Offset Stake The following screens are only accessed if you choose to stake a point at a specified offset away from the catch point. Station: displays the current station being slope staked. Offset from CP: is the offset from the catch point specified in the previous screen. From Gun to Design Point: displays the angle and distance information from the total station to the design point.
Stakeout Menu Point Slope Staking Stakeout Point Slope Staking. The Point Slope Staking routine is a simplified version of the Slope Staking routine described on Page R-293. The Point Slope Staking routine determines the location of the catch point from a known hinge point and a specified horizontal direction from the hinge point, whereas the Slope Staking routine determines the location of the catch point from a perpendicular offset to a known centerline at a specified station.
Survey Pro Reference Manual Point Slope Staking – Screen Two The second screen is used to perform the actual point slope staking shots. Rod Elev: is the current elevation at the rod location. Des. Slope: is the design cut or fill slope. Obs. Slope: is the computed (observed) cut or fill slope based on the last shot and the corresponding hinge point. HD to HP: is the horizontal distance from the rod to the hinge point.
Stakeout Menu EDM: This button can be toggled to shoot in various EDM modes. The options available depend on the total station being used. Consult the total station’s documentation for more information on the EDM modes that it supports. • Results : This will open the Slope Staking Results screen, listing detailed information for the current setup and last shot.
Survey Pro Reference Manual • Automatic Slope : selects the slope that is nearest to the current rod position. • Force CUT Slope : forces all computations to be based on a cut slope. • Force FILL Slope : forces all computations to be based on a fill slope. HR: is the rod height. : opens the Smart Target options (Page R-449). Topo SS… : will store the last shot taken as a side shot. Shot : takes a shot. < Back : returns to the previous screen. Store > : opens the next screen.
Stakeout Menu Stake Line and Offset Stakeout Line and Offset. The Stake Line and Offset screen is used to stake stations on a line, or at an offset to it, at fixed intervals. : opens the Stakeout Settings screen (Page R-47). Start Point: defines the first point of the line to be staked. End Point / Direction : defines the second point of the line, or the direction of the line to be staked, respectively. Begin Station: defines the station associated with the Start Point.
Survey Pro Reference Manual Vertical Offset : is the offset distance that is below the design location (when D is selected) or above the design location (when is selected). U Grade: specifies a slope from the specified line to the parallel line that is being staked. When this is a non-zero value, the elevation for the staked points will increasingly differ from the design elevations as the Offset value increases. Height of rod: is the length of the rod. Backsight… : opens the Backsight Setup screen.
Stakeout Menu turning to an obscure angle value. When this button is tapped, the following actions will occur: 1. A new backsight circle value is computed, sent to the instrument and stored in the raw data 2. The Angle Right value is changed to zero to reflect the change. The instrument now needs to be turned horizontally to zero to face the current target location. 3. To prevent errors if this button is used, the backsight set up is invalidated when exiting the Stakeout dialog.
Survey Pro Reference Manual Stake Curve and Offset Stakeout Curve and offset. The Stake Curve and Offset screen is used to stake stations on a curve or at an offset to it at fixed station intervals. : opens the Stakeout Settings screen (Page R47). PC Point: is the starting point of the curve (point of curvature). PC Tangent Azm / PC Tangent Brg : defines the azimuth or bearing, respectively, of the tangent at the PC Point.
Stakeout Menu Next Station : advances the Station to Stake by the Station Interval. Offset: is the horizontal distance of the offset from the specified curve. The offset occurs on the left (while viewing the curve from the PC) when the L is selected or on the right when the R is selected. Note: An offset of zero would result in the specified curve being staked. V.
Survey Pro Reference Manual Curve and Offset – Screen Three Station: displays the current station that is being staked. H. Offset: displays the offset distance of the curve being staked from the specified curve and if it is on the Right or Left side of the specified curve. Angle Right: is the horizontal angle that the total station must aim toward so that it is facing the current station. Horz. distance: is the horizontal distance from the occupy point to the current station.
Stakeout Menu Note: The Circle Zero button is not available when using a robotic total station. < Back : returns to the previous screen. Stake > : opens the next screen, which is identical to the third Stake Points screen, described on Page R-276. Screen Summary Screen One is used to define the primary curve to determine the location of the curve to be staked and the station associated with the PC Point.
Survey Pro Reference Manual Stake Spiral and Offset Stakeout Spiral and Offset. The Stake Spiral and Offset screen allows you to stake stations at fixed intervals on a spiral curve, or at an offset to it. Start Point: is the point associated with the beginning of the spiral curve. This can either be the TS or the CS, which is specified later in this screen (see below).
Stakeout Menu Stake Spiral and Offset – Screen Two Station to Stake: is the desired station on the spiral curve that you want to stake. Station Interval: is the value that is added to the Station to Stake after the Next Station button is pressed. Next Station : advances the Station to Stake by the Station Interval. Offset: is the horizontal distance of the offset from the spiral curve.
Survey Pro Reference Manual Note: A motorized total station will automatically turn toward the design point after pressing Solve> depending on the configuration of the Stakeout Settings screen (Page R-47). Stake Spiral and Offset – Screen Three Station: displays the current station that is being staked. H. Offset: displays the offset distance of the spiral curve being staked from the specified spiral curve and if it is on the Right or Left side of the specified spiral curve.
Stakeout Menu 3. To prevent errors, the backsight set up is invalidated when exiting the Stakeout dialog if this button has been used. A circle zeroed on a design point is meaningless once the design point has been staked. Note: The Circle Zero button is not available when using a robotic total station. < Back : returns to the previous screen. Stake > : opens the next screen, which is identical to the third Stake Points screen, described on Page R-276.
Survey Pro Reference Manual Show Station Stakeout Show Station. The Show Station routine allows you to take a shot to a prism that is positioned anywhere near a polyline, a range of points that define a line, or an alignment to see where the prism is located in relation to the line. Tap Line… : allows you to tap an existing polyline or alignment that the station and offset will be computed from. To/From… : Opens the Point List screen (Page R-443) where a point list can be created.
Stakeout Menu Show Station and Offset – Screen Two The second Show Station and Offset screen is used to take a shot to the prism and view the data. Height of Rod: is the length of the rod. EDM: This button can be toggled to shoot in various EDM modes. The options available depend on the total station being used. Consult the total station’s documentation for more information on the EDM modes that it supports. Station: displays the station at the rod position.
Survey Pro Reference Manual Store Offset Points Stakeout Store Offset Points. The Store Offset Points screen is used to store points in the current job at a specified offset from an existing polyline or alignment at a specified interval. Tap Line… : allows you to tap an existing polyline or alignment that the station and offset will be computed from. To/From… : Opens the Point List screen (Page R-443) where a point list can be created. Begin Station: is the station assigned to the beginning of the line.
Stakeout Menu Note: A negative slope will result in water running from the centerline toward the edge of payment. ; Stake Curb / Ditch: When checked, a curb or ditch and an offset can be defined beyond the edge of the pavement. Height: is the height of the curb or ditch in feet or meters. A positive value is considered a curb and a negative value a ditch. Offset From Edge of Road: is the distance that the curb or ditch extends from the edge of pavement.
Survey Pro Reference Manual Start Point: is the point number that will be assigned to the first offset point that is stored. Each stored point that follows will be assigned the next available point number. Description: is the description that will be assigned to all the offset points that are stored. ; Center Line: offset points will be stored at locations on the centerline when checked.
Stakeout Menu Stake DTM Stakeout Stake DTM. The Stake DTM routine allows you to stake an area and get cut/fill information between the point being staked and a reference DTM surface at the same horizontal coordinates. You can also obtain volume information between the surface being staked and a specified reference elevation or the reference DTM surface. The reference DTM surface can be defined by a layer in the current job or a file loaded on the data collector.
Survey Pro Reference Manual Warning: If importing a DXF or DTM file where the distance units in the source file are different than the distance units for the current job, the imported coordinates will be converted to the current job’s distance units when they are imported. This is normally the desired result, but it can cause a problem if the distance units for the imported data or the current job were set incorrectly.
Stakeout Menu point is stored to it. You can also view this surface with live cut/fill volumes at anytime from the 3D View screen (Page R-85). Note: Viewing the DTM during DTM Stakeout is a useful quality assurance technique to determine where additional points are needed. Setup / View DTM : opens the Setup DTM 3D screen (Page R-80) where the non-reference DTM layers are configured and optionally viewed from the 3D View screen (Page R-85).
Survey Pro Reference Manual Stake DTM – Screen Two Stakeout Stake DTM Next >. The second Stake DTM screen displays all relevant information for the current rod position and a graphic that shows the reference DTM surface and its corners. Once a shot is taken, the rod location and the occupied TIN triangle are displayed. Data: shows the angle and distance information from the previous shot.
Stakeout Menu Desc: is the description that will be assigned to the next stored stake point. HR: is the height of the rod. : opens the Smart Target options (Page R-449). EDM: This button can be toggled to shoot in various EDM modes. The options available depend on the total station being used. Consult the total station’s documentation for more information on the EDM modes that it supports. Take Shot… : triggers the total station to take a shot to the prism.
Survey Pro Reference Manual Station Staking Stakeout Station Staking. The Station Staking routine allows you to stake the stations, offsets, and surfaces built into a LandXML file. The first Station Staking screen is used to load a LandXML file and view the details of that file. The box on the left displays the horizontal view of the centerline include within the LandXML file and the box on the right shows the vertical view.
Stakeout Menu Cross-Section View Stakeout Station Staking View Cross-Sections. The Cross-Section View screen is used to view the station, surface, and offset details of the loaded LandXML file. The upper portion of the screen lists the Station, Northing, Easting, and Elevation at the selected node. The larger graphic area displays the crosssectional view of the selected surface. The smaller graphic area displays the horizontal view of the centerline.
Survey Pro Reference Manual Station Staking – Screen Two Stakeout Station Staking Next >. The second Station Staking screen is used to configure which Station, Surface, and Offset you want to stake. and buttons to Use the corresponding scroll the available Station, Surface, and Offset that you want to stake. Height of Rod: is the rod height. Backsight… : opens the Backsight Setup screen (Page R-118) where you can set your backsight. < Back : returns to the previous screen.
Stakeout Menu 1. A new backsight circle value is computed, sent to the instrument and stored in the raw data 2. The Angle Right value is changed to zero to reflect the change. The instrument now needs to be turned horizontally to zero to face the design point. 3. To prevent errors, the backsight set up is invalidated when exiting the Stakeout dialog if this button has been used. A circle zeroed on a design point is meaningless once the design point has been staked. 4.
Survey Pro Reference Manual Define a Location Stakeout Define a Location. The Define a Location screen is used to manually enter the distance and direction to a new point from any existing reference point and then stakeout the new point. From Point: is the reference point that the specified angle and distance information is applied to for locating the new point. Azimuth / Bearing : is the direction from the reference point to the new point.
Stakeout Menu Ref. Point: is the reference point specified in the From Point field in the previous screen. Description: is the description for the reference point. From Gun to Location: displays the angle and distance information from the total station to the new point. Users would aim their nonrobotic total station the direction specified here.
Survey Pro Reference Manual Where is Next Point Stakeout Where Is Next Point. The Where is Next Point screen is used to assist the rod person in locating another point, given the current rod point, a reference point, and the point to locate. Current Rod Pt: is the current rod point. Next FS Point: is the point that the rod person wants to locate. Increment: is added to the Next FS Point value after pressing the Next Point > button.
Stakeout Menu Where is Next Point – Screen Two This screen shows two graphics that indicate the direction and distance that the rod person must travel to reach the Next FS Point. The clock-style graphic shows the current rod location at the center, a line in the 12 o’clock position indicates the direction to the Reference, and an arrow shows the direction to the Next FS Point. There is also a text indicator that explains the direction to travel in a clock format.
Stakeout Menu – GPS and Basic GPS The Stakeout Menu while running in GPS mode with either the GPS module or Basic GPS module contain the routines used to stake existing points and other known locations. Items shown in gray utilize the GPS Staking screen described on the following page and are otherwise identical to the conventional stakeout routines described starting on Page R-273.
Survey Pro Reference Manual Stake Points Stakeout Stake Points. The GPS Staking screen is used to navigate to a design point with the receiver in roving mode. Once the design point has been staked, this screen is also used to control static occupations for the most precise measurement to the as built point.
Stakeout Menu – GPS & Basic GPS Module indicator will stop updating to assist you in more precisely locating the design point as illustrated below. Rover is greater than 3 m (10 ft) from the design point. Rover is between 0.3 and 3 m (1 and 10 ft), from the design point. Rover is within 0.3 m (1 ft) of the design point.
Survey Pro Reference Manual Note: The Display Directions As field in the Stakeout Settings screen configures the format for the text that directs you to the design point. CUT / FILL: displays the required cut or fill between the current elevation and the design point. Ref: 0°00’00”… : opens a screen where you can select a reference azimuth or point, which will then be displayed on the navigation graphic as a blue line to assist in orienting yourself.
Stakeout Menu – GPS & Basic GPS Module to configure rover antenna and the backsight information is replaced with rover antenna height information. See Page R-282 for details. Stake to Line – Screen Two The second screen is where measurements take place and the staking directions are displayed. The graphic and display direct you to points on line via the shortest route, a perpendicular offset from the rover to the line. The graphic display will change depending on how close you are to the specified line.
Survey Pro Reference Manual the receiver. If this area of the screen is tapped, the epoch count stops and the GPS Status screen opens (Page R-172). Go SOUTH / NORTH: displays the distance the rover must move in a south or north direction to reach the closest point on the line. Go EAST / WEST: displays the distance the rover must move in an east or west direction to reach the closest point on the line. OCCUPYING / ROVING : switches from ROVING to OCCUPYING mode.
Stakeout Menu – GPS & Basic GPS Module Slope Staking Stakeout Slope Staking. The Slope Staking screen is used to locate the catch points for a roadway in any terrain. The first screens of this routine are similar to the conventional method except that the Backsight and Circle Zero buttons are replaced with a Setup HR button to configure rover antenna and the backsight information is replaced with rover antenna height information. See Page R-293 for details.
Survey Pro Reference Manual the receiver. Tap on this button to open the detailed GPS Status screen (Page R-172). The first button selects the type of slope that will be used between the catch point and hinge point from the following options: • Automatic Slope : selects the slope based on the current rover position. If the rover is above the hinge point, a cut slope is computed. If the rover is below the hinge point, a fill slope is computed.
Stakeout Menu – GPS & Basic GPS Module Results: displays the results computed from the last Shot. Obs. Slope: is the computed (observed) cut or fill slope based on the last shot and the corresponding hinge point. Des. Slope: is the design cut or fill slope. Cut / Fill: is the cut or fill required for the current rover location to be positioned on the design slope.
Survey Pro Reference Manual Line and Offset Stakeout Line and Offset. The instructions for the Line and Offset routine for GPS similar to the conventional method, except that the Backsight and Circle Zero buttons are replaced with a Setup HR button to configure rover antenna and the backsight information is replaced with rover antenna height information. See Page R-303 for details. Curve and Offset Stakeout Curve and Offset.
Stakeout Menu – GPS & Basic GPS Module Show Station and Offset Stakeout Show Station. The Show Station and Offset routine allows you to position the rover anywhere near a polyline, a range of points that define a line, or an alignment to see where the rod is located in relation to the selected line.
Survey Pro Reference Manual Elev: is the elevation at the rod position. Offset: displays if the rod is on the Left or Right of the line. Segment: displays the type of line segment at the current station. < Back: returns to the previous screen. Store : stores a point for the current rod location. Store Offset Points Stakeout Store Offset Points.
Stakeout Menu – GPS & Basic GPS Module Stake DTM Stakeout Stake DTM. The Stake DTM routine allows you to stake an area and get cut / fill and volume information based on a reference DTM or specified elevation datum. The first screen of this routine is similar to the conventional method, except that the Backsight button is replaced with a Setup HR button to configure rover antenna and the backsight information is replaced with rover antenna height information. See Page R-319 for details.
Survey Pro Reference Manual 3D View… : opens the 3D View screen (consult the conventional surveying Reference manual) where a 3D view of the DTM can be viewed from any angle as well as cut / fill information for the current location. Note: The 3D View… button is only available when Generate TIN w\Staked Points is checked in the previous screen and at least three stake points have been stored.
Stakeout Menu – GPS & Basic GPS Module C.L.: shows the current station and offset information for the rover location relative to the selected centerline. The type of line segment in the polyline at the current station is also displayed. (This card is only available if the With C.L. checkbox was checked in the previous screen.) Note: Tapping anywhere within the map view will open a larger map view, which provides zoom controls. Where is Next Point Stakeout Where is Next Point.
Inverse Menu The Inverse Menu contains routines that compute the direction and distance between two objects.
Survey Pro Reference Manual Inverse Point to Point Inverse Point to Point. The Inverse Point to Point screen will calculate the distance and direction between two existing points. Begin Point: is the reference point used to compute the distance and direction to the End Point. End Point: is the point whose relationship to the Begin Point is computed. Select from Map… : allows you to quickly select both the Begin Point and End Point from a map view.
Inverse Menu Inverse Point to Line Inverse Point to Line. The Inverse Point to Line screen computes the perpendicular offset distance and direction from a known point to a continuous line defined by two points or one point and a direction. Inverse Point: is the known point that the offset information to a specified line is computed. Begin Station: is the beginning station value that corresponds with the Start of Line, which is used to compute the inverse station in the results.
Survey Pro Reference Manual North: is the Y-coordinate on the specified line, tangent to the perpendicular offset. East: is the X-coordinate on the specified line, tangent to the perpendicular offset. Elevation: is the elevation on the specified line, tangent to the perpendicular offset. Inverse Point to Polyline Inverse Point to Polyline. The Inverse Point to Polyline screen computes the offset distance from a known point perpendicular to a polyline.
Inverse Menu Solve : will compute the distance and direction of the offset from the known point perpendicular to the polyline. Note: There is no solution if a perpendicular offset does not occur within the extents of any selected polyline segments. Results Station: is the station along the polyline where the offset occurs, starting from the Begin station. Offset: is the horizontal distance of the offset.
Survey Pro Reference Manual Inverse Point to Multiple Points Inverse Multiple Points. The Inverse Point to Multiple Points screen will calculate the distance and direction from an existing point to one or more other points. Inverse point: is the reference point used to compute the distance and direction to the other points. Tap Points : provides a map view where you can tap multiple points. To/From : Opens the Point List screen (Page R-443) where a point list can be created.
Inverse Menu Inverse Point to Location / Point Inverse Location / Point. The Inverse Point to Location / Point screen will calculate the distance and direction from any point or location to another point or location. Begin: is the reference point or location used to compute the distance and direction to another point or location. End: is the other point or location whose correlation to the Begin point or location is computed.
Cogo Menu The Cogo Menu contains all of the coordinate geometry routines used to perform computations from the existing job data.
Survey Pro Reference Manual Point in Direction Cogo Point in Direction. The Point in Direction screen will calculate and store the position of a new point after providing a distance and direction from a known point. From point: is the point name of the reference point used for locating the new point. Azimuth / Bearing : is the direction from the reference point to the new point. +/- Angle: is the angle added to the Azimuth / Bearing to modify the direction to the new point.
Cogo Menu Intersection Cogo Intersection. The Intersection screen computes the intersection(s) of two lines given the direction(s) and/or distance(s) from two existing points. (See illustration below.) Once solved, the intersection points can be viewed from the Map view and optionally stored.
Survey Pro Reference Manual Map The Map card is used to determine which intersection points were computed and are and . You can then return labeled with a to the Input card to select which of these points to store.
Cogo Menu Offset Line Cogo Offset Line. The Offset Line screen is used to view, store a polyline, or store an alignment that is at a specified perpendicular offset to an existing set of points, a polyline, or an alignment. Tap Line… : allows you to tap an existing polyline or alignment that the offset will be computed from. To/From… : Opens the Point List screen (Page R-443) where a point list can be created. Offset: defines the offset distance and which side the offset occurs.
Survey Pro Reference Manual Offset Points Cogo Offset Points. The Offset Points screen is used to store points at a specified perpendicular offset to an existing polyline, alignment, or point range. Points can be stored that correspond with the nodes of an alignment, points of a polyline, and/or at a specified station interval. Tap Line… : allows you to tap an existing polyline or alignment that the offset points will be computed from.
Cogo Menu Solve : computes the offset points, and stores them if the Store Pts checkbox is checked. Station Offset Cogo Station Offset. The Station Offset screen will compute and optionally store a point at a specified station and offset to an existing polyline or alignment. The elevation for the stored point will always be set to the elevation of the first node of the polyline, or alignment. Start Station: is the station for the first node of the selected line.
Survey Pro Reference Manual Corner Angle Cogo Corner Angle. The Corner Angle screen provides information on the horizontal angle created from three known points. Backsight: is an end point of the angle to be solved. Middle Point: is the corner point of the angle to be solved. Foresight Point: is the other end point of the angle to be solved Select from Map… : Allows you to quickly select all of the above points from a map view.
Cogo Menu Compute Area Cogo Compute Area. Allows you to compute the area of a selected boundary. Tap Line… : allows you to tap an existing polyline from a map view. To/From… : Opens the Point List screen (Page R-443) where a point list can be created. Solve : will compute the area of the selected boundary. Results Area: is the area that the boundary encloses. If the boundary is not closed, the area is computed as if a line joined the two ends. Length: is the length of the selected boundary.
Survey Pro Reference Manual Triangle Solutions Cogo Triangle Solutions. The Triangle Solutions screen will solve for the unknown parts of a triangle after providing three known parts. Triangle Solution: is where you select the parts of the triangle that are known. You can select any of the following from the dropdown list: • Side-Side-Side: The lengths of all three sides are known. • Angle-Side-Angle: Two angles and the side between them are known.
Cogo Menu Map Check Cogo Map Check. The Map Check screen is used to manually enter boundaries from a map to check for closure and other information related to the boundary. Edit… : opens the appropriate editor screen where you can edit the selected line or curve from the list. Delete : deletes the selected line segment. Clear : clears all line entries. Closure : opens the Results page. Add Line… : opens the Add / Edit Line screen, (Page R-368), where a new line can be added prior to the select segment.
Survey Pro Reference Manual Error dist.: is the distance between the last point and the first point. Error azm: is the direction from the last point to the first point Precision: is the ratio between the Error distance and Perimeter. Add / Edit Line The Add / Edit Line screen is used to enter a new line to the list prior to the selected line segment. Azimuth / line. Bearing : is the direction of the Length: is the length of the line, in feet or meters. : enters the line to the list.
Cogo Menu Mid Ordinate : The distance between the curve and the chord at the center of the curve’s length. External : The minimum distance between the PI and the curve. Azimuth / Bearing : defines the direction of the curve, tangent at the PC. Turn: defines if the curve turns to the Left or Right while viewing the curve from the PC Point. : appends the curve to the list. Add to Map The Add to Map screen is used to add the existing line and curve data to the current job as a polyline.
Survey Pro Reference Manual Predetermined Area Cogo Predetermined Area. The Predetermined Area routine will take a boundary with one open side and compute the location of a line that will enclose the boundary with a specified area using the Hinge Method or the Parallel Method. 4 (hinge) 1 ? The Hinge Method computes the location of the side of a boundary that can pivot on a fixed point.
Cogo Menu Editor… : opens the Polyline Editor (Page R65) where a new polyline can be created or an existing polyline can be modified. Tap Points… : provides a map view where you can tap any existing points to define the fixed sides of the boundary. To/From… : Opens the Point List screen (Page R-443) where a point list can be created. ; Store Pt 1 / 2: When checked, will store a point at the location of the end point(s) of the computed boundary line.
Survey Pro Reference Manual HD/VD to SD/ZA Cogo HD/VD to SD/ZA. The HD/VD to SD/ZA screen will convert a vertical and horizontal distance to an equivalent slope distance and zenith angle. Horz Dist: is the horizontal distance from the occupy point to the foresight point. Vert Dist: is the vertical distance from the occupy point to the foresight point. HI: is the distance that the total station is above the ground. HR: is the length of the rod. : opens the Smart Target options (Page R449).
Cogo Menu SD/ZA to HD/VD Cogo SD/ZA to HD/VD. The SD/ZA to HD/VD screen will convert a slope distance and zenith angle to an equivalent horizontal distance and vertical distance. Slope Dist: is the slope distance to be converted. Zenith: is the zenith angle to be converted. HI: is the distance that the total station is above the ground. HR: is the length of the rod. : opens the Smart Target options (Page R449).
Survey Pro Reference Manual AU Conversion Cogo AU Conversion. The AU (Architectural Units) Conversion screen will convert distances with fractional inches to decimal distances. If the job is configured for International Feet or US Survey Feet, it is assumed that the distance entered in this screen is in the same units as the job. If the job is configured for meters, it is assumed that the distance entered in this screen is in International Feet.
Curve Menu The Curve Menu contains routines that will compute all aspects of a horizontal curve and assist in curve layout.
Survey Pro Reference Manual Curve Solution Curve Curve Solution. The Curve Solution screen provides detailed information on a curve when two parts of the curve are known. The first known part of the curve is defined by one of the following: • • Radius : is the distance from the radius point to the curve. Delta : is the deflection angle. • Degree Arc : is the deflection angle that results in a 100-ft. arc length. • Degree Chord : is the deflection angle that results in a 100-ft. chord length.
Curve Menu Results: Radius: is the distance from the radius point to the curve. Length: is the arc length. Chord: is the chord length. Deg. Arc: is the deflection angle that results in a 100-ft. arc length. Deg. Chord: is the deflection angle that results in a 100-ft. chord length. Delta: is the deflection angle. Tangent: is the distance from the PC or PT to the PI. PI 10 d hor 0’ C Mid-Ordinate Long Chord rd ho g. C De rc g.
Survey Pro Reference Manual Known PI and Tangents Curve PI and Tangents. The PI and Tangents screen is used to compute and store the PC, PT, and radius points when the PI point and the direction of both tangents are known, along with one other curve attribute. PI Point: is the PI point. Azm PI->PC / Brg PI->PC : is the direction of the tangent from the PI to the PC. Azm PI->PT / Brg PI->PT : is the direction of the tangent from the PI to the PT.
Curve Menu Results Radius: is the distance from the radius point to the curve. Delta: is the deflection angle. Tangent: is the distance from the PC or PT to the PI. Three Point Curve Curve 3 Point Curve. The Three Point Curve screen will compute the details of a curve when three points of the curve are specified; the PC, PT and any other point on the curve; or the PC, PT and radius point. First point: is the first point from the current job that defines the curve.
Survey Pro Reference Manual Solve : will compute the curve based on the selected points. Traverse : opens the Traverse on Curve screen (Page R-388), where the curve can be included in a traverse. Layout : opens the Curve Layout screen (Page R-381), where the location of points on a curve can be computed at any station interval. Results Radius: is the distance from the radius point to the curve. Length: is the arc length. Chord: is the chord length. Delta: is the deflection angle.
Curve Menu Compute Radius Point Curve Radius Point. The Compute Radius Point screen is used to compute and optionally store the radius point for a curve when certain parts of the curve are known. PC Point: is the point that defines the beginning of the curve (Point of Curvature). PT Point: is the point that defines the end of the curve (Point of Tangency). Turn: specifies if the curve turns to the Left or Right as you face the curve from the PC.
Survey Pro Reference Manual Results Radius: is the distance from the radius point to the curve. Length: is the arc length. Chord: is the chord length. Deg. Arc: is the deflection angle that results in a 100-ft. arc length. Deg. Chord: is the deflection angle that results in a 100-ft. chord length. Delta: is the deflection angle. Tangent: is the distance from the PC or PT to the PI. External: is the minimum distance between the PI and the curve. Mid Ord.
Curve Menu Line Tangent to Circle Curve Tangent to Circle. Will compute the location of a line that is tangent to the specified sides of two specified circles. Tangent Line: determines which sides of the circles the computed line will be tangent to as you occupy the 1st Radius Point and face the 2nd Radius Point. (See illustration below.) 1st / 2nd Radius Pt: defines the points around which the circles are computed. Radius: defines the radius of the circles that are used to compute the Tangent Line.
Survey Pro Reference Manual Curve Layout Curve Curve Layout. The Curve Layout screen is used to assist in the layout of a horizontal curve by computing the direction and distance to points on the curve using a variety of methods. Method: The method determines how the points on the curve are laid out. Each method is described below. PC Deflection: provides deflection angles and distances to each station on the curve as if occupying the PC and backsighting the PI.
Curve Menu • PT Current P I to Station S tat RP ion Deflection PI Deflection: provides deflection angles and distances to each station on the curve as if occupying the PI and backsight the PC. The results are given in the following format: o Station: is the current station on the curve. o Deflection: is the angle to turn to the current station. o PI to Station: is the distance from the PI to the current station.
Survey Pro Reference Manual Chord Offset: provides perpendicular offset information from the chord (the line from the PC to the PT) for each station on the curve. PC deflection information is also provided. The results are given in the following format: Chord dist.: is the distance on the long chord from the PC (toward the PT) where the perpendicular offset occurs. o Chord offset: is the distance to the current station on the curve, perpendicular to the long chord.
Curve Menu • External : is the minimum distance between the PI and the curve. PC Station: is the starting station assigned to the PC. ; Interval: When checked, all necessary information for each station at the specified interval on the curve will be computed. Start station: when not computing by interval (above), only the information for the particular station entered here is computed. Solve : will solve and display all the details of the specified curve, without the layout information.
Survey Pro Reference Manual Traverse on Curve Curve Trav. on Curve. The Traverse on Curve screen will compute the PT and radius point for a curve when the tangent azimuth at a PC point is known. The first known part of the curve is defined by one of the following: • • Radius : is the distance from the radius point to the curve. Delta : is the deflection angle. • Degree Arc : is the deflection angle that results in a 100-ft. arc length.
Curve Menu ; Store PT: When checked, will store the computed PT point with the specified point name. ; Store RP: When checked, the computed radius point will be stored with the name specified here. Solve : will compute and store the PT, and if desired, the radius point. Results Radius: is the distance from the radius point to the curve. Length: is the arc length. Chord: is the chord length. Delta: is the deflection angle. Tangent: is the distance from the PC or PT to the PI. Mid Ord.
Survey Pro Reference Manual Parabolic Curve Curve Parabolic Curve. The Parabolic Curve screen provides detailed information on a vertical parabolic curve when certain parts of the curve are known. Known: The PVC or PVI radio button is selected to define which point on the curve is known. One of the following options must be selected from the dropdown list: • Curve Length: is selected when the length of the curve is known.
Curve Menu Note: When the begin and end grades are both positive or both negative, the high / low elevation will not be located between the PVC and PVT. PVC / PVI Station: is the station for the specified point. PVC / PVI Elevation: is the elevation for the specified point. Begin Grade: is the grade at the tangent of the PVC. End Grade: is the grade at the tangent of the PVT. Solve : computes the details for the vertical curve.
Survey Pro Reference Manual Parabolic Layout Curve Parabolic Layout. The Parabolic Layout screen allows you to compute an elevation at a specified station, or a station at a specified elevation. Beg. Grade: is the percent grade at the PVC. End Grade: is the percent grade at the PVT. Curve Length: is the horizontal distance between the PVC and PVT. PVC Station: is the starting station at the PVC. PVC Elevation: is the elevation at the PVC.
Curve Menu Results PVC sta.: is the station at the PVC. PVI sta.: is the station at the PVI. PVT sta.: is the station at the PVT. elev.: is the elevation for the respective point. Hi/Lo sta.: is the station where the vertical curve has a tangent equal to zero (the crest of the curve).
Survey Pro Reference Manual Straight Grade Curve Straight Grade. The Straight Grade screen will solve for the elevation at a specified station or a station at a specified elevation on a straight grade. Begin Station: is the station where the straight grade begins. Begin Elev: is the elevation at the Begin station. Grade: is the percent slope ( Rise ⋅ 100 ). Run Solve for: is where you select to solve for an Elevation or a Station.
Curve Menu Spiral Curve Spiral. The Spiral screen will compute the details of a spiral curve, given the spiral length and radius. Spiral length: is the length of the spiral curve. Radius: is the circular curve radius. Solve : computes the details of the spiral curve. Layout… : opens the Spiral Layout screen (Page R-396) where the location of stations on the spiral curve can be computed. Traverse… : opens the Traverse on Spiral screen (Page R-397).
Survey Pro Reference Manual Spiral Layout Curve Spiral. The Spiral Layout screen is used to compute station locations on a spiral curve. Radius: is the radius of the circular curve. Spiral Length: is the length along the spiral curve from TS to SC. TS station: is the station at the TS point. ; Interval: When checked, is the spiral arc distance that is added or subtracted from the Current Station using the Sta + and Sta – buttons. Current Station: is the station on the curve that is computed.
Curve Menu Traverse on Spiral Curve Trav. on Spiral. The Traverse on Spiral screen is used to compute the location of, and optionally store the SC, or ST and spiral PI points. Radius: is the radius of the circular curve. Length: is the length along the spiral curve from TS to SC. TS / CS Point: is the existing point associated with the TS or CS point. Azimuth / Bearing : is the tangent direction at the TS or CS point.
Survey Pro Reference Manual Results Tangent In: the tangent direction entering the spiral at the TS or CS. Tangent Out: the tangent direction exiting the spiral at the SC or ST. X of Throw: is the distance along the tangent where a perpendicular line intersects with the radius point. Y of Throw: is the minimum distance between the tangent and the extended circular curve. X: is the distance from the TS to the SC along the tangent. Y: is distance from the SC to the tangent.
Roads Menu The Roads Menu contains the routines used to perform road layout.
Survey Pro Reference Manual Add/Edit Templates Roads Edit Templates. The Add/Edit Templates screen is used to edit an existing template or create a new template. Templates describe the cross-sectional profile of a roadway. They can contain information such as the road width, its slope, a curb, and/or a ditch. Each separate portion of a template is called a segment. All templates must have at least one segment and all templates of a particular road must have the same number of segments.
Roads Menu Edit Template Roads Edit Templates Edit…. or Roads Edit Templates New…. The Edit Template screen is identical to the New Template screen and is used to create a new template or edit an existing one. All of the segments of the current template are listed in the screen. The list shows the name of each segment, the horizontal and vertical offsets (lengths), and the slope. Note: The length of the first segment must be greater than zero.
Survey Pro Reference Manual Note: The selected segment is shown with a thicker line in the map view in the lower portion of the Edit Template screen. Remove : removes the selected segment and automatically joins the previous segments to the following segments. Note: When a segment is removed the existing segments toward the centerline will not change. Only those on the side of the removed segment away from the centerline are adjusted. Edit Segment Roads Edit Templates Edit… Insert….
Roads Menu Edit Alignments Roads Job Edit Alignments or Edit Alignments. The Edit Alignments screen is used to create an alignment that defines the centerline of a road containing both horizontal and vertical elements. Editing alignments is fully described, starting on Page R-68. Add/Edit Roads Roads Edit Roads. The Add/Edit Roads screen is used to define your road. This is where the templates are added to the alignment and any widenings and super elevations are defined.
Survey Pro Reference Manual • Delete alignment alignment name?: Answering Yes to this prompt will delete the selected alignment(s) from the current job so they are no longer displayed in the Edit Alignments screen. In this case, the alignment can be re-associated with the Import… routine from the definition in the RD5 file. Answering No to this prompt will open the next prompt without deleting the selected alignment(s) from the current job. • Delete Roadname.
Roads Menu The Road Card Roads Edit Roads ( New… or Edit… ) Road. The Road card of the New Road screen is used to select the alignment to use for the road. If an alignment has not yet been created, refer to Page R-68 for information on creating an alignment. Road Name: is the name assigned to the road. The name must not be the same as any existing road name. Alignment Description: displays the name of the selected alignment.
Survey Pro Reference Manual • Confirm the first template coincides with the starting station. • Confirm that all template segments have a name. (The names do not have to be unique.) • Confirm that the same number of segments exist on each side of the alignment. • Confirm that each widening start station is less than the corresponding widening’s end station. • Confirm that one widening does not overlap with another widening.
Roads Menu Road Profiles Screen Roads Edit Roads ( New… or Edit… ) Road View Profiles…. The Road Profiles screen allows you to see information about the cross-sectional profile of the road at any station after at least one template has been added to each side of the road. << , >> : these buttons move a red circle icon that starts at the centerline, which is indicated by a green circle, to each node of the template at the current station.
Survey Pro Reference Manual Description: is the name of the current alignment. A new name can be assigned to the alignment from this field. Point / Location : depending how this button is toggled, you can change the POB of the alignment by entering a new point number or new coordinates. Start Station: replaces the existing starting station of the alignment with the starting station entered here. The Templates Card Roads Edit Roads ( New… or Edit… ) Templates.
Roads Menu Add / Edit Template Screen Roads Edit Roads (New… or Edit…) Templates (Add… or Edit…) The Add / Edit Template screen allows you to add a template to the road or edit an existing template. Template: The Template column lists all the templates that can be added to the road. Selecting a template will display an image of that template in the lower corner of the screen. Once the first template is added, this box will only list templates with the same number of segments as the first.
Survey Pro Reference Manual The Widenings Card Roads Edit Roads ( New… or Edit… ) Widenings. The Widenings card of the New Road screen is used to add or edit widenings. A widening is a section of a road that changes in width, but does not necessarily require any new templates. The road width is adjusted by changing only the width of the first segment of the template that leads into the beginning of the widening. Any additional segments, like those that may describe a sidewalk or ditch, are not adjusted.
Roads Menu screen, which allows you to add a widening to the same side of the road that was selected. Edit : allows you to edit the selected widening in the Edit Widening screen, which is identical to the Add Widening screen. Remove : removes the selected widening from the list. Check… : checks the road for errors and displays the results in the Roads Report screen, described on Page R-405.
Survey Pro Reference Manual Super Elevations Card Roads Edit Roads ( New… or Edit… ) Super Elevations. The Super Elevations card of the New Road screen is used to add or edit super elevations. A super elevation changes the cross slope of the first segment of a template in order to bank a curve – the slope of any remaining segments will remain unadjusted. One super elevation defines a begin point and an end point where the slope change begins and where it finishes the transition for one side of a road.
Roads Menu Add / Edit Super Elevation Screen Roads Edit Roads (New… or Edit…) Super Elevations (Add… or Edit…) The Add / Edit Super Elevation screen allows you to add a super elevation to the road or edit an existing super elevation. Start Station: is the location of the beginning of the super elevation on the alignment. Length / End Station : is the length of the super elevation measured from the Start Station, or it is the end station, depending on how the button is toggled.
Survey Pro Reference Manual Hinge on Center / Edge : determines if the super elevation is computed by rotating the road around the centerline or the road’s edge. Note: When hinging on edge, the road is actually rotated around the end of the first segment of the template that leads into the super elevation. Only the first segment is adjusted with a super elevation. The length and slope of any segments beyond the first will not be adjusted from a super elevation.
Roads Menu Road Stakeout Roads Road Stakeout. The Stake Road screen is used to stake any segment of a road profile at any station. Use Station Equation: When checked, the current station equation will be applied to the road. Equation Settings : opens the Station Equation screen (Page R-427) where a station equation can be configured. Tap Road… : opens the Tap on a Road screen where you can tap on any road in the job to select it. Name: displays the name of the selected road.
Survey Pro Reference Manual Next Station : advances the Station to Stake by the Station Interval. Note: If the Stake Corners option is selected in the Stakeout Settings screen, the Next Station button will also stop at any horizontal or vertical alignment node, and the beginning and end of any widening and super elevation that falls within the interval. << , >> : These buttons are used to select the particular node, or an offset to it, from your road profile that you wish to stake.
Roads Menu Next > : takes you to the next Stake Road screen where the direction and distance information to the stake point is displayed. Stake Road – Screen Three The third Stake Road screen displays distance, direction, and other information about the point to be staked. Station: displays the station where the stake point occurs and the type of line segment it falls on in the alignment.
Survey Pro Reference Manual zeroed on a design point is meaningless once the design point has been staked. Note: The Circle Zero button is not available when using a robotic total station. < Back : returns to the previous screen. Stake > : opens the final Stake Road screen where the shots to the stake point are performed. Stake Road – Screen Four Height of Rod: is the length of the rod. Design Elev: displays the current design elevation, which can be modified with the Change… button.
Roads Menu Shot : takes a shot to the prism and computes come/go, cut/fill information. Shot data: displays the measurements from the last shot. Store… : opens the next screen. Store/Tape… : opens the Stake Out Point (Tape Offset) dialog box (Page R-309), where the staked point can be stored that includes a specified offset. The default value is the appropriate distance correction to the design point. Topo SS… : stores a side shot using the data from the last shot taken. (This will not take a new shot.
Survey Pro Reference Manual Note: This screen will not appear if the Write Cut Sheet Data Only (No Store Point) checkbox is checked in the Stakeout Settings screen, although the Results screen will still appear if the Show Results on OK checkbox was never unchecked from this screen. (It is checked by default.) Stake Road – Stakeout Results This screen shows detailed cut/fill values, which may be needed when marking a road or offset stake.
Roads Menu Road Slope Staking Roads Slope Staking. The Road Slope Staking screen is used to locate the catch point of the road at any station. Tap Road… : opens the Tap on a Road screen where you can tap on any road in the job to select it. Name: displays the name of the selected road. Begin Station: displays the station assigned to the beginning of the road. End Station: displays the final station in the road. road.
Survey Pro Reference Manual Road Slope Staking – Screen Two The second Road Slope Staking screen is used to set up some slope stake parameters prior to slope staking the road. Station: is the station to be slope staked. Station Interval: specifies how far to advance from the current station to the next station. Next Station : advances the current station by the Station Interval.
Roads Menu Slopes Card The Slopes card is used to specify the cut and fill slopes that will be used when computing the location of the catch point. The default values are the slopes stored in the template for the section being staked. To override a default slope, check the appropriate box and key in the new slope. The new slope entered will always be used regardless of the values stored in the templates. Changes to slopes will be reflected in the V. Map card graphic.
Survey Pro Reference Manual Road Station and Offset Roads Show Station. The Road Station and Offset routine allows you to take a shot to a prism that is positioned anywhere on the road and compute the details of where that point is located in relation to the road. This information can then be compared to the data from a grade sheet. Tap Road… : opens the Tap on a Road screen where you can tap on any road in the job to select it. Name: displays the name of the selected road.
Roads Menu Road Station and Offset – Screen Two The second Road Station and Offset screen is used to take a shot to the prism and view the data from various cards. Height of Rod: is the length of the rod. EDM: This button can be toggled to shoot in various EDM modes. The options available depend on the total station being used. Consult the total station’s documentation for more information on the EDM modes that it supports. Shot : takes a shot to the prism. < Back : returns to the previous screen.
Survey Pro Reference Manual Cross-Section Card Station: displays the station at the rod position. Template: displays the name of the template that is used at the rod position. Segment: displays the name of the template’s segment at the rod position. Cut / Fill: is the necessary cut or fill that will bring the rod position even with the road’s surface. Cut / Fill to CL: is the necessary cut or fill that will bring the rod position to the same elevation as the centerline at the current station.
Roads Menu Station Equation Roads Road Stakeout Equation Settings. or Roads Slope Staking Equation Settings. or Roads Show Station Equation Settings. The Station Equation screen is used to configure the stationing for an alignment with stationing that changes at a specific location. This situation might occur where the road you are staking merges with another road and once you stake past the point where the roads merge, you want to use the stationing assigned to the other road.
Adjust Menu The Adjust Menu contains routines to perform a variety of adjustments.
Survey Pro Reference Manual Scale Adjust Scale. The Scale screen will scale the distances of a range of points relative to a specified base point. This is useful to correct a survey where a scale factor was inadvertently applied during data collection. Tap Points… : allows you to select points by tapping them from a map view. To/From… : Opens the Point List screen (Page R-443) where a point list can be created. Base point: The distances to all the selected points will be scaled relative to this point.
Adjust Menu Translate Adjust Translate. The Translate screen will move a group a points horizontally and vertically by a specified distance and direction. Tap Points… : allows you to select points by tapping them from a map view. To/From… : Opens the Point List screen (Page R-443) where a point list can be created.
Survey Pro Reference Manual Point / Location : allows you to enter either a point name or location coordinates. Solve : adjusts the selected points in the same direction or distance as defined from the From point to the To point, or by the direction and distance entered. Information will be written to the raw data file detailing the adjustment.
Adjust Menu Rotate Adjust Rotate. The Rotate screen will rotate selected points around a specified point. This is useful to correct a survey where an incorrect backsight was used during data collection. Tap Points… : allows you to select points by tapping them from a map view. To/From… : Opens the Point List screen (Page R-443) where a point list can be created. Rotation Point: The selected points will be rotated around the point specified here. (The coordinates for the rotation point will not change.
Survey Pro Reference Manual Solve : will perform the rotation on the selected points and change the coordinates accordingly. Information will be written to the raw data file detailing the adjustment. Traverse Adjust Adjust Traverse Adjust. The Traverse Adjust wizard is a series of screens that allow you to adjust a closed traverse for angular error and/or perform a compass rule adjustment on a closed or open traverse.
Adjust Menu The user cannot explicitly define the side shots that are adjusted. Instead, they are determined by the information stored in the raw data file. If no side shots were stored from any of the traverse points, an error message will be displayed and no adjustment is performed. If any of the following settings were changed during or after the traverse was recorded, then side shots cannot be adjusted.
Survey Pro Reference Manual Traverse Adjust – Angle Adjustment If an angle adjustment is being performed, this screen will appear next. Closing Angle: is the closing angle for the traverse, which must be represented as an angle-right. (See illustration.) 3 4 Next > : opens the next screen of the adjustment wizard.
Adjust Menu Traverse Adjust – Compass Rule If a compass rule adjustment is being performed, this screen will appear next. Closed Traverse: select this option if you are adjusting a closed traverse. Close to Known Location: select this option if you are adjusting an open traverse and closing to a known point or location. Note: if a closing location is not specified, it is automatically assumed that the first point of the traverse will be the closing location.
Survey Pro Reference Manual Traverse Adjust – Results This screen displays the changes that will be made by the adjustment, where they can be previewed before the actual adjustment is made. The screen lists the adjustment details in three main sections: the angle adjustment details; the compass rule adjustment details, and the point details where the beforeand-after coordinates for each point are listed. An example of the information provided in the Preview screen is shown here.
Miscelaneous Screens The following screens are only available via a Quick Pick or a power button (see the User’s Manual). They are not available directly from any menu item.
Survey Pro Reference Manual Past Results , Past Results (where applicable) When the Past Results option is used to enter a value in a specific field that was computed previously within Survey Pro. Select the line that contains the value that you want to use and tap . The selected value will then be entered in the field associated with that power button.
Miscellaneous Screens Trimble Slant HR -> HR (From any HR field), Trimble Slant HR -> HR This option only applies when using a Trimble Traverse Kit that allows the measurement of a Slant HR instead of the usual HR. When this option is selected, it will convert a Slant HR entered in an HR field to a standard HR. This must be performed each time a new Slant HR is entered in the HR field. Consult the documentation that came with the Trimble Traverse Kit for more information on correctly measuring a Slant HR.
Survey Pro Reference Manual Quick Pick Editor , Edit Quick Pick (located at bottom of list) The Quick Pick Editor is used to customize the list of routines available from the Quick Pick button . Menu Items: Is a dropdown list containing the menu items you would normally see in the Main Menu. Selecting a menu item from this list will display all of the routines from that menu item that can be included in the Quick Pick list. Routines listed in bold are already in the Quick Pick list.
Miscellaneous Screens Point List Editor Tap from a variety of screens. The Select Point(s) screen is used to define a simple list of points or a list of points that define a line that can include curves depending on where the screen is accessed from. Examples of how to enter different lists of points are displayed in the lower portion of the screen. See Point Lists in the User’s Manual for more information.
Survey Pro Reference Manual Map View or from the command bar in various screens. Map View without basemaps Map View with basemaps Many screens provide access to a map view, which shows data from the current job. It can be accessed from the Main Menu in the command bar with the button, or any screen that has a button. Some map views display additional information, such as a vertical profile. Tip: You can pan around your map by dragging your finger or stylus across the screen.
Miscellaneous Screens Zoom To Point Button: prompts you for a point name and then the map view will be centered to the specified point with the point label displayed in red. Turn To Point Button: Tap this button and then tap a point in the map view to automatically turn the total station to the selected point. This is only available when a robotic total station is selected and Remote Control is active in the Instrument Settings. Increase Vertical Scale: is only available when viewing a vertical profile.
Survey Pro Reference Manual Map Display Options From the Map View, tap The Map Display Options screen is used to configure the information that is displayed in the Map View. Show Points: will show a dot for each point in view. Smart Point Labels: displays only certain point labels (name and description) when many points are grouped together to reduce clutter. Names: will show the point name for each point that is in view. Descriptions: will show the point description for each point in view.
Miscellaneous Screens Manage Basemaps From the Map View, tap , Manage Basemaps. The Manage Basemaps screen is used to select the basemaps to display in the map view for the current job. Consult the User’s Manual for more information on using basemaps. The main portion of the screen lists the names of all the basemaps that have been added to the current job. The other columns display if each basemap is visible and the number of elements in the vector basemaps.
Survey Pro Reference Manual Edit Basemaps From the Map View, tap Manage Basemaps The Edit Basemaps screen is used to preview the selected basemap, and if it is a vector basemap, the way the basemap appears can be changed. The Preview page shows how the selected basemap will look in the map view. Visible: when checked, the selected basemap will be visible in the map view.
Miscellaneous Screens Smart Targets Tap a power button next to a (indicating a prism Smart (indicating a reflectorless Target is currently selected) or Smart Target is currently selected). This item is available from any screen where the rod height can be adjusted. Smart Targets provide a convenient way to work with different prisms and/or target types on the same job. See the User’s Manual for more information.
Survey Pro Reference Manual Activate : Activates the selected Smart Target. The active smart target is marked with the symbol. Note: It is not necessary to access the Manage Smart Targets screen to activate a different Smart Target. You can quickly activate a Smart Target by tapping next to any HR field and then tap the desired Smart Target from the list that appears. Edit Smart Target , Manage Smart Targets, Add or Edit.
Miscellaneous Screens Prism Type: This option allows you to choose one of the following three types of prisms when using a supported Trimble total station: • Generic: Select this option if using a generic (non-Trimble 360°) prism. It is up to the user to enter the correct prism constant and manually angle the prism vertically toward the total station before taking any shots to avoid introducing error. • Trimble 360° (2mm): Select this option when using a Trimble 360° prism.
Survey Pro Reference Manual prism eliminating the possibility of the total station tracking a different reflector that comes into view. Using Active Prism: Check this option when using an active prism. (This option is only available when using a total station that supports active prisms.) Note: In order to perform automatic repetitions when using active prisms, active prisms must be set up over both the backsight and foresight.
Miscellaneous Screens Disable Touch-Screen [CTRL] - [ ] (space) This option can be used to disable the touchscreen when it is necessary to wipe it off. Press [ESC] to reactivate the touch-screen and return to Survey Pro. You can also temporarily deactivate the touchscreen using either of the following methods: • Use the , Suspend Screen quick pick. Press [ESC] to reactivate. • Ranger 300X/500X only: Press [Fn] [ ]. Repeat to reactivate.
Appendix A Transverse Mercator Zones Central Meridians for State Plane Coordinates E = East W = West C = Central State Zone Alabama E W Central Meridian 85 50 87 30 Alaska 2 3 4 5 6 7 8 9 E C W 142 00 146 00 150 00 154 00 158 00 162 00 166 00 170 00 110 10 111 55 113 45 Arizona Delaware 75 25 Florida E W 81 00 82 00 Georgia E W 82 10 84 10 State Zone Hawaii 1 2 3 4 5 Central Meridian 155 30 156 40 158 00 159 30 160 10 Idaho E C W 112 10 14 00 115 45 Illinois E W 88 20 90 10 India
Reference Manual State Zone Mississippi E W Central Meridian 88 50 90 20 Missouri E C W E C W Nevada State Zone New Mexico 90 30 92 30 94 30 E C W Central Meridian 104 20 106 15 107 50 New York E C W 74 20 76 35 107 50 115 35 116 40 118 35 Vermont New Hampshire 71 40 New Jersey 74 40 Wyoming 72 30 1 2 3 4 105 10 107 20 108 45 110 05 Lambert Zones Central Meridian and Zone Constants for State Plane Coordinates N = North S = South C = Central A-2 NC = North Central SC = South Centr
Appendix A State Zone Arkansas N S 1 2 3 4 5 6 7 N C S California Colorado Connecticut Florida Iowa Kansas Kentucky Louisiana Maryland Massachusetts Michigan Minnesota Montana Nebraska N N S N S N S N S O M I N C S N C S N C S N S Central Meridian 92 00 92 00 122 00 122 00 120 30 119 00 118 00 116 15 118 20 105 30 105 30 105 30 72 45 84 30 93 30 93 30 98 00 98 30 84 15 85 45 92 30 91 20 91 20 77 00 71 30 70 30 87 00 84 20 84 20 93 06 94 15 84 20 109 30 109 30 109 30 100 00 99 30 Zone Constant 0.
Reference Manual New York (Long Island) North Carolina North Dakota Ohio Oklahoma Oregon Pennsylvania South Carolina South Dakota Tennessee Texas Utah Virginia Washington West Virginia Wisconsin A-4 N S N S N S N S N S N S N S N NC C SC S N C S N S N S N S N C S 74 00 0.654082 79 00 100 30 100 30 82 30 82 30 98 00 98 00 120 30 120 30 77 45 77 45 81 00 81 00 100 00 100 20 86 00 101 30 97 30 100 20 99 00 98 30 111 30 111 30 111 30 78 30 78 30 120 50 120 30 79 30 81 00 90 00 90 00 90 00 0.577171 0.
Index # 2 peg test ......................R-268 procedure ..................... 185 2D/3D points ..................... 42 3D view...........................R-85 3D view settings ............R-85 A about Survey Pro ...........R-33 add/edit break-lines102, R-82 adjust with projection274, R236 projection calculator.... 278 prompt adjust .............. 277 results .......................... 278 select coordinate system276 select points................. 275 adjustment ...................R-269 angle.........
Reference Manual command bar..................... 10 compass rule.................... 163 compass rule adjustment164, R-437 compute area............... R-365 compute radius point .. R-381 conformal map projections203 conformality .................... 202 connect to receiver ...... R-181 control fileSee import control control files.............. 31, R-26 control points112, 249, 255, R195 Basic GPS ................ R-254 check .............R-196, R-255 collect ........................... 282 occupy...........
Index edit segment...................R-71 EGM96 ............................ 198 ellipsoid height................ 207 ellipsoid scale factor 206, 278 ephemeris ........................ 128 exit ..................................R-33 export *.CR5 coordinates ......R-24 *.JOB coordinates ......R-23 *.TXT coordinates ......R-24 .CSV coordinates ........R-25 LandXML coordinatesR-26 export coordinates .......... 112 F feature collection. 268, R-191 features...........................R-61 field label............
Reference Manual WGS84(1996.0)............ 195 I import .................... 226, R-15 *.GPS coordinates ..... R-17 *.JOB coordinates ..... R-16 *.TXT coordinates ..... R-18 LandXML coordinatesR-20 import control.................. 112 import coordinates .......... 108 import GPS control260, R-231 index card .......................... 14 input field .......................... 12 input shortcuts.................. 14 installation Recon................................ 4 instrument profile.........
Index parameters .................. 252 pick from database...R-209 residuals ...................R-212 residuals for Basic GPS .R251 set zone .....................R-207 solve ..........................R-210 solve for Basic GPS ..R-251 vertical card..............R-213 with control points ...... 248 localization calculator..R-214 M main menu ...................9, R-3 manage basemaps........R-447 manage layers ................R-87 map check............ 145, R-367 map display options.....R-446 map projection ..
Reference Manual point to line inverse .... R-351 point to location inverseR-355 point to multiple points inverse...................... R-354 point to point inverse.. R-350 point to polyline inverseR-352 points on DTM layer ..... R-84 polyline .............................. 44 polylines......................... R-64 post process ................. R-174 post processing ........ 235, 270 data collection.......... R-199 file management...... R-243 office procedure ........... 273 settings.....................
Index stake out ...................... 270 rx settings ......................R-97 S save as ............................R-14 save point .....................R-154 scale ............. 158, 258, R-430 scale factor .... 202, 204, R-46 ellipsoid........................ 278 mapping plane..... 204, 278 scale factor calculator..... 278 scroll button ...................... 13 SD/ZA to HD/VD ..........R-373 select point(s) ........ 16, R-443 server mode ....................R-31 set origin..........................
Reference Manual choose base setup ........ 238 choose one point setup 236 choose projection mode 236 connect to receiver....... 239 rover setup................... 242 start GPS survey wizardR-178 station and offset ........ R-314 road .......................... R-424 station equation .... 95, R-427 station offset................ R-363 stereographic projection 204, 205 store offset pointsR-316, R-344 straight grade.............. R-394 sun shot ............... 127, R-157 super elevations ..........
Index Windows Networking294, 299 WW15mGH.grd............... 208 Z zone constant ...........
