Product Manual

5. Move the laser to point B and align the level beam to point
C again.
6. Mark the location of the square beam (D) on the floor.
Note: To ensure accuracy, the distances from A to B, B to C,
and B to D should be equal.
7. Turn the laser 90° so that the level beam aligns with point D.
8. Mark the location of the square beam (E) on the floor as close
as possible to point A.
9. Measure the distance between points A and E. If the
measurement is greater than the values shown below, the laser
must be serviced at an authorized service center.
Room length or distance The 90° angle between the
between points A and C level beam and square beam is out
of calibration if the distance between
points A and E is:
10 m (35 ft) >9.0 mm (
3
/8 in.)
20 m (70 ft) >18.0 mm (
3
/4 in.)
Checking Level to Square Beam 90° Calibration
Refer to the graphic for the location of the laser at each step and
for the location of the marks made at each step. All marks can be
made on the floor by placing a target in front of the level or square
beam and transferring the location to the floor.
– 13 – – 14 – – 15 – – 16 –
–
17 – – 18 –
– 19 – – 20 –
– 21 – – 22 – – 23 –
N324
Trimble - Precision Tools
5475 Kellenburger Road
Dayton, Ohio 45424 U.S.A.
www.spectralasers.com
© 2017, Trimble Inc. All rights reserved.
Reorder PN 1213-2030 Rev. B (10/17)
差
>5 mm
1)
2)
3)
4)
Notice to Our European Union Customers
For product recycling instructions and more information,
please go to: www
.trimble.com/environment/summary.html
Recycling in Europe
To recycle Trimble WEEE,
call: [phone], and
ask for the “WEEE associate,” or
mail a request for recycling instructions to:
Trimble Europe BV
c/o Menlo Worldwide Logistics
Meerheide 45
5521 DZ Eersel, NL
North & Latin America
Trimble - Precision Tools
5475 Kellenburger Road
Dayton, Ohio 45424
U.S.A.
[phone] (Toll Free)
[phone] Phone
[phone] Fax
Europe
Trimble Kaiserslautern GmbH
Am Sportplatz 5
67661 Kaiserslautern
GERMANY
[phone] Tel
[phone] Fax
Africa & Middle East
Trimble Export Middle-East
P.O. Box 17760
Jebel Ali Free Zone, Dubai
UAE
[phone] Phone
[phone] Fax
Asia-Pacific
Trimble Navigation
Australia PTY Limited
Level 1/120 Wickham Street
Fortitude Valley, QLD 4006
AUSTRALIA
[phone] Phone
[phone] Fax
China
Trimble Beijing
Room 2805-07, Tengda Plaza,
No. 168 Xiwai Street
Haidian District
Beijing, China 100044
[phone] Phone
[phone] Fax
www.trimble.com.cn
Request for Service
Our goal is to provide prompt and efficient service through
competent service dealers. To locate your local dealer or authorized
Trimble Service Center, contact our world centers listed below.
7. Adjust the laser’s height until the beam is superimposed over
the mark made in step 5.
8. Without changing the height of the laser, rotate it 180° to place
the beam near the mark on the first wall (step 3).
9. Measure the vertical distance between the beam and the mark
made in step 3. If the measurement is greater than the values
shown below, the laser must be serviced at an authorized
service center.
Distance Between Walls Measured Value
6 m (20 ft) 3.0 mm (
1
/8 in.)
12 m (40 ft) 6.0 mm (
1
/4 in.)
18 m (60 ft) 8.0 mm (
5
/16 in.)
24 m (80 ft) 11.0 mm (
7
/16 in.)
1. In an area with at least 6 m (20 ft) between two parallel walls,
place the laser 50–75 mm (2–3 in.) from one wall, facing
the wall.
2. Press the power button.
3. Locate the position of the level beam on the wall and make
a mark.
4. Rotate the laser 180° so that the laser faces the other wall.
5. Locate the position of the level beam on the wall and make
a mark.
6. Move the laser to the far wall, facing the wall.
Checking Accuracy—Level
6. Measure the difference
between the two marks on the
ceiling, which will be twice the
actual error. If the difference is
more than 6 mm in 10 m (1/4
inch in 30 ft), the laser must
be serviced at an authorized
service center.
4. Rotate the laser 180° and
realign the down beam
over the reference mark on the
floor.
5. Locate the position of the
up beam on the ceiling, which
will be twice the actual error,
and make a mark.
1. Press the power button.
2. Place the laser so that
its down beam is over a
reference mark on the floor.
3. Locate the position of the up
beam on the ceiling and make a
mark.
Calibration
Before each use, be sure to check the pocket laser for signs of
damage. If the laser has been dropped or subjected to other rough
treatment, it should be checked for accuracy.
Checking Accuracy—Plumb
Warranty
Trimble warrants the LP51 and LP51G to be free of defects in
material and workmanship for a period of three years. Trimble or
its authorized Dealer or service center will repair or replace, at its
option, any defective part, or the entire product, for which notice
has been given during the warranty period. This warranty period is
in effect from the date the system is delivered by Trimble or its
authorized Dealer to the purchaser, or is put into service by a
Dealer as a demonstrator or rental component.
Trimble or its Authorized Service Center will repair or replace, at
its option, any defective part or components of which notice has
been given during the warranty period.
Customers should send products to the nearest Authorized Factory,
Dealer, or Service Center for warranty repairs, freight prepaid. In
countries with Trimble Service Subsidiary Centers, the repaired
products will be returned to the customer, freight prepaid.
Any evidence of negligent, abnormal use, accident, or any attempt
to repair equipment by other than factory-authorized personnel
Trimble certified or recommended parts, automatically voids the
warranty.
Special precautions have been taken to ensure the calibration of
the laser; however, calibration is not covered by this warranty.
Maintenance of the calibration is the responsibility of the user.
The foregoing states the entire liability of Trimble regarding the
purchase and use of its equipment. Trimble will not be held
responsible for any consequential loss or damage of any kind.
This warranty is in lieu of all other warranties, except as set forth
above, including an implied warranty merchantability of fitness for
a particular purpose, is hereby disclaimed. This warranty is in lieu
of all other warranties, expressed or implied.
D
X
A
B
C
X
E
X
Steps 1-4
Mark point A.
Set up laser over
point A. Mark
points B & C
Steps 5-6
Set up laser over
point B. Align to
point C. Mark
point D.
Steps 7-8
Turn laser 90
and align to
point D. Mark
point E.
1. Find a room at least 10 m
(35 ft) long. Mark a point
(A) on the floor at one end
of the room.
2. Set up the laser so that its
down beam is over point A.
Make sure the level beam
points toward the far end
of the room.
3. Mark a point (B) on the
floor at the center of
the room using a target
to transfer the level beam
location to the floor.
4. Mark a point (C) on the
far wall or transfer the level
beam location to the floor.
Difference
> 6 mm (> 1/4 in)
Laser Safety
Use of this product by people other than those trained on this
product may result in exposure to hazardous laser light.
• Do not remove warning labels from the unit.
• LP51G is a Class 2 laser product (< 1mW; 520-635 nm).
• LP51 is Class 3A/3R (< 5mW; 635 nm).
• Never look into the laser beam or direct it to the eyes of other
people.
• Always operate the unit in a way that prevents the beam from
getting into people‘s eyes.
LP51 NOTE: It is required to post a Laser Safety Sign and to
read, sign and carry a Laser Operator's Card when this laser is
operated in public places.
To download and print the required materials please visit our
website at www.spectralasers.com