Product Manual
Table Of Contents
- Slide Number 1
- TABLE OF CONTENTS Introduction For Your Safety Components How to Use the Laser System Powering the Laser Turning On/Off the Laser Laser Setup Standard Features Rotation Mode Scan Mode Manual Mode Y-/X-Single Slope Mode Mask mode Activating/Deactivating Standby Mode Operating Examples Determining the Height of Instrument (HI) Using the optional HL760/HL760U receiver Pairing the HL760/HL760U receiver with the transmitter
- Special Features using the optional RC402N RC402N Features and Functions Powering the RC402N Turning On/Off the RC402N Radio Remote Control Pairing the remote control with the transmitter MENU Features at the RC402N Rotation Scan Automatic Grade Match Automatic PlaneLok Mask mode Line Scan (Vertical Setup) Beam Plunge (Vertical Setup) Setting Menu Info Service menu Setting Menu Selections HI-alert selection Sensitivity Language CALIBRATION Checking Calibration of the Y- and X-Axes Checking Calibration of the Z-(vertical) Axis Wall Mount PROTECTING THE UNIT CLEANING AND MAINTENANCE PROTECTING THE ENVIRONMENT WARRANTY TECHNICAL DATA
- Introduction Thank you for choosing one of the Spectra Precision Lasers from the Trimble family of precision lasers. The HV302/HV302G laser is an easy-to-use tool that allows you to take accurate horizontal/vertical measurements, 90°- and plumb beam transfer. For Your Safety For hazardless and safe operation, read all the user guide instructions. - Use of this product by people other than those trained on this product may result in exposure to hazardous laser light. - Do not remove warning labels from the unit. - The HV302/HV302G is a class 3A/3R laser (<5 mW; 600 - 680 nm / G - 520 nm) IEC 60825-1:2007) - Never look into the laser beam or direct it to the eyes of other people. - Always operate the unit in a way that prevents the beam from getting into people's eyes. - If initial service is required, which results in the removal of the outer protective cover, removal must only be performed by factory-trained personnel. Caution: Use of other than the described user and calibration tools or other procedures may result in exposure to hazardous laser light. Caution: Using different than described at the HV302/HV302G user guide, may result in unsafe operation.
- HV302/HV302G - Components
- Components a Power Button b Battery LED c Manual/Standby Button d Leveling LED e HI/Manual/Standby LED f Up and Down Arrow Buttons g Left and Right Arrow Buttons h Rotation Button i Scan Button j Rotor
- Installing Batteries Remove the battery door by turning the center screw 90° counterclockwise. Insert batteries (or a rechargeable battery pack) into the housing so that the negative poles are on the bigger battery spiral springs. DO NOT REMOVE RECHARGEABLE BATTERIES FROM THEIR HOLDER AND INSTALL ALKALINE BATTERIES, SEVERE DAMAGE TO UNIT WILL RESULT IF CHARGING IS ATTEMPTED. Install the battery door and tighten it by turning the center screw 90° clockwise. A mechanical switch prevents alkaline batteries from being charged. Only the original rechargeable battery pack allows charging within the unit. Any other rechargeable batteries have to be charged externally.
- Recharging the Batteries Note: The battery LED shows the approximate charge of the batteries. The LED will flash when battery voltage is between 3.8 and 4.0 volts. The LED will be on continuously when battery voltage is less than 3.8 volts. The charger requires approx. 13 hours to charge empty rechargeable batteries. For charging, connect the plug of the charger to the recharge jack of the unit. New or long-time out-of-use rechargeable batteries reach their best performance after being charged and recharged five times. For Indoor applications the charger can be used as a power supply for the GL. Alkaline batteries can be used as a backup. Insert 4 D-cell batteries noting the plus (+) and minus (-) diagrams at the battery door. The batteries should only be charged when the laser is between 50° F and 104° F (10°C to 40°C). Charging at a higher temperature may damage the batteries. Charging at a lower temperature may increase the charge time and decrease the charge capacity, resulting in loss of performance and shortened life expectancy.
- Slide Number 9
- Slide Number 10
- Slide Number 11
- Slide Number 12
- Slide Number 13
- Slide Number 14
- Slide Number 15
- Slide Number 16
- Special Features using the optional RC402N RC402N Features and Functions The remote control mirrors the basic functionality of the laser keypad and offers additional features using the M and E buttons.
- Powering the RC402N 1. Open the battery door using a coin or similar pry device to release the battery door tab on the RC402N. RC402N will be shipped with alkaline batteries Rechargeable batteries can be used optional but need to be charged externally. 2. Insert two AA batteries noting the plus (+) and minus (-) diagrams inside the battery housing. 3. Close the battery door. Push down until it “clicks” into the locked position. Turning On/Off the Radio Remote Control The radio remote control is a hand-held device that allows you to send operational commands to the laser from a remote location. Press the power button to turn on the radio remote control. Note: When the remote control is initially turned on, the standard display (model number and software version) appear for the first 3 seconds, then the RC402N LCD shows the actual laser function. With every button press, the LCD backlight is activated and turns off automatically if no button is pressed for 8 seconds. To turn off the radio remote control, press and hold the power button for 2 seconds. If the RC402N is outside of the operating range or not paired with the transmitter, the LCD shows the model number and software version. Note: 5 minutes after the last button press, the remote control turns off automatically.
- Slide Number 19
- Slide Number 20
- Slide Number 21
- Slide Number 22
- Slide Number 23
- Slide Number 24
- Slide Number 25
- Slide Number 26
- Slide Number 27
- Slide Number 28
- Slide Number 29
- Slide Number 30
- Slide Number 31
- Slide Number 32
- Slide Number 33
- Slide Number 34
- Slide Number 35
24
Mask mode
Press and release the M button at the Standard Display and select >>Mask Mode<<.
Depending on which side the beam should be turned off, the required side can
be selected. Press and release the E button, the mask symbol occurs.
For selecting the side, press and release one of the arrow button.
When all areas have been set, press button E to store the mask sector selection
until the unit will be turned off.
Note: The unit always powers up with the mask mode deactivated (default).
Setting Menu
Please see the Setting Menu details at the following pages.
Info
Press and release the M button at the Standard Display and select >>Info<<.
Up and Down Buttons can be used to toggle between About LS, Runtime and Radio
Press and release button E to confirm the selection.
The laser information (software version, serial number.), the runtime and the radio
channel of the laser will be displayed.