Quick Start Guide

Temperature Reading Panel with
Face and Mask Recognition
Quick Start Guide
Microphone
18-pin
Interface
Power
Interface
1.34in
Package
Overview
1
2
Plastic Plug ×4
IR Temperature
Measurement Module
Infrared
Light
Display
Screen
Speaker
Micro SD
Card Slot
Reset
USB Port
5.45in
11.88in
14
15
16 17
D0 D1
GND
BUT
10
11
12
13
IN1
GND
IN2
GND
2CH alarm input
Power Input
12V0
PE
GND
IN1
GND
Cable Connection
3
18-pin Interface
1 2 3 4 5 6 7 8 9
NO2 NO1 NO3COM2 COM1 COM3
NC3
D+
RS 485
D-
2CH alarm output
Lock interface
18
GND
D0
GND
D1
+
+
+
+
+
+
-
-
-
-
-
-
RS485+
RS485-
Anode/
Magnetic
Lock
Cathode
Lock
D0
D1
GND
NC3
COM3
NO3
IN2
GND
COM1
NO1
COM2
NO2
D+
D-
BUT
GND
Warning
This camera should be installed by qualified personnel only. All the examination and repair work should
be done by qualified personnel. Any unauthorized changes or modifications could void the warranty.
Statement
This guide is for reference only. Product, manuals and specifications may be modified without prior
notice. Speco Technologies reserves the right to modify these without notice and without incurring any
obligation. Speco Technologies is not liable for any loss caused by improper operation.
Regulatory Information
FCC conditions:This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:This device may not cause harmful interference.This device must accept any interference
received, including interference that may cause undesired operation.FCC compliance:This equipment has
been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communication. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Note:
Before installation, check the package and make sure that all components are included. Contact your rep or
Speco customer service department immediately if something is broken or missing in the package.
Do not drop the camera or subject it to physical shock.
Keep away from liquid while in use.
Do not touch the screen with sharp objects.
If cleaning is necessary, please use clean cloth to wipe it gently, avoiding water or alcohol.
Device
Quick Start Guide
QR code
for manual
Drill Template Bracket
Front Back
Left
Right
White Fill
Light
Cameras
Wiegand interface
Exit Button
Connector
Alarm Input1
Alarm
Output1
Alarm Input2
Alarm
Output2
RS 485
Wiegand
Interface
Lock
Exit Button
+12V
Earth
GND
Alarm Input Device
Alarm Input Device
Alarm Output Device
Access Control Security Module
Alarm Output Device
Power
Power
Power
Power
Card
Reader
Exit Button
Router
Switch
Or
Note:
* The wiegand terminal here is a wiegand input terminal. If you want to connect
to an access controller, you shall set the Wiegand direction to “Output”.
* The RS 485 interface of this device supports security module access. Once the security
module is enabled, the exit button and lock control will be invalid.
Tapping Screw×4
Screw (KM3*7)×2
Screwdriver
This device is not intended for use in the diagnosis of
any disease or other conditions or in the cure,
mitigation, treatment, or prevention of any disease.
O2TML
(Minimum 1A)