O2MB1 Full HD Mini-bullet IP Camera
O2MB1 User ’s Guide Directions Be careful not to cause any physical damage by dropping or throwing the camera. Especially keep the device out of reach from children. Do not disassemble the camera. No after service is assumed when disassembled. Use only power adapters compatible with the unit. Be careful to prevent moisture or water penetration into the unit. Particular attention is needed when installing the unit.
O2MB1 User ’s Guide Revision History Date Revision th Mar 4 , 2014 1.0 First manual revision creation. th Mar 7 , 2014 1.1 Text revisions th 1.2 Modified “2.3.3. Front and Rear view of Encoder box” Apr 25 , 2014 Details Rev.1.2 (Apr.
O2MB1 User ’s Guide Contents 1. Introduction .................................................................................................................................................... 5 1.1. Overview ................................................................................................................................................... 5 1.2. Specifications...................................................................................................................................
O2MB1 User ’s Guide 1. Introduction 1.1. Overview The O2MB1 is a full HD mini bullet IP camera with a separate encoder box. It is a multi-codec (H.264, MJPEG) IP camera (or network camera) built with embedded software and hardware technology. It enables real time transmission of synchronized video of up to 1080P and audio data. Remote clients can connect to O2MB1 for the real time video/audio data through various client solutions running on PC or smart device.
O2MB1 User ’s Guide 1.2. Specifications Camera Image sensor Progressive scan 1/2.7 inch CMOS 2.0M pixels Full resolution 1,920 x 1,080 pixels (Full HD) Min. illumination Color : 0.12 Lux (F1.4) S/N 39dB or more Ratio White Balance AWB DSS Supported WDR Supported Lens 3.7mm, F2.5 Day & Night N/A Video Compression method Simultaneous Dual Codec (H.
O2MB1 User ’s Guide External Terminals LAN 10/100BaseT LAN (auto MDIX) Alarm input / output Alarm I/O (1 Sensor input & 1 Relay output) Factory Reset Supported Audio MIC/Line in, Line out Power DC 12V input Alternate Power Standard PoE IEEE802.
O2MB1 User ’s Guide 2. Product Description 2.1. Contents The product package contains followings : Contents O2MB1 Accessories CD Quick Reference Guide Description Remarks O2MB1 main unit 5m Video Cable 1EA, Screws, Anchors L-type wrench with six angles Software & User’s Guide Quick installation guide 2.2.
O2MB1 User ’s Guide 2.3. Physical description 2.3.1. External View Figure 2-1. External view of O2MB1 2.3.2. Dimension Unit : mm Figure 2-2. Dimension Rev.1.2 (Apr.
O2MB1 User ’s Guide 2.3.3. Front and Rear view of Encoder box Figure 2-3. Front view Pin Description 1 Line Output 2 Ground 3 MIC/Line Input 4 Relay Output 5 Relay Output 6 Sensor Input (-) 7 Sensor Input (+) HDMI Connect Camera Module Figure 2-4. Rear view 2.3.4. Factory Default Switch Factory default switch is provided for returning the IP camera to factory default state. Unscrew the cover to access the switch. There are two functions assigned to factory default switch. 1.
O2MB1 User ’s Guide 2.4. Functional Description Power : Power input for supplying 12V DC, 0.5A power. Caution : If O2MB1 is powered by PoE, do not plug in DC Jack with active DC power into DC power connector. Network (LAN) 100Mbps Ethernet connector (RJ-45) with PoE standard (802.3af). LED on the Ethernet connector shows the status of O2MB1 as the followings: - Link LED It will be lit with orange color when network cabling is all right.
O2MB1 User ’s Guide Relay Output Relay output is provided for connecting alarm devices or for remote on/off control of devices such as light. Relay is normal open and it will be closed upon alarm annunciation or remote on. The relay is capable of switching 30V AC/DC, 2A. For the application which needs power switching beyond this limit, use additional relay switch as shown in the right of Figure 2-6.
O2MB1 User ’s Guide 3. On Site Installation Use cables and conduits that are suitable for the installation. Particular attention should be paid in the installation so that no moisture is allowed to penetrate into the unit through the cables or conduits during the life time of the product. Products of which the internal parts are exposed to moisture because of improper installation are not covered by warranty 1. Fix the base on the wall. 2.
O2MB1 User ’s Guide 4. Getting Started Brief information for first time operation of O2MB1 is provided in this chapter. 4.1. PC Requirement Audio/Video streaming data received from O2MB1 can be displayed or stored in a PC running client programs.
O2MB1 User ’s Guide DC adaptor LAN switch LAN switch with standard POE (802.3af) Figure 4-1. Power and network connection 4.2.2. Install Speco-NVR and set IP parameters on O2MB1 Speco-NVR is a multi-channel VMS program for the IP camera. Install Speco-NVR on remote PC to connect to these products. It is needed to assign connection information to Speco-NVR program before connection. Insert the CD provided with product into the PC and install Speco-NVR. Admin Page Button ONSIP Installer Figure 4-2.
O2MB1 User ’s Guide iv) You can connect to admin page by clicking on (10). 3 1 2 9 10 5 4 7 6 8 Click on the field in (3) for sorting and rearranging the list. Select network mode that best suits from the drop down list in (5). You can choose either Static or ADSL and Auto (DHCP), respectively. If ADSL and Auto are selected, the fields in (6) are deactivated. In case of ADSL, fill the User Name and Password in (8) with the values provided by your ISP.
O2MB1 User ’s Guide 4.2.3. Remote video connection to O2MB1 1. Connection through Web Viewer Web Viewer offers simplest way of video connection to O2MB1. For video connection, enter the IP address of O2MB1 in the URL window of Internet Explorer as: [e.g.] Port 80 Can be omitted the default port of 80 [e.g.] Port 8080 Note : Active-X module should be installed on your PC before actual connection. If your PC is not connected to the internet, you cannot download Active-X module.
O2MB1 User ’s Guide 2. Connection through Speco-NVR Click the camera assignment button for setting the camera address. Input the description, address, Ch#, User ID, Password and port and then click the save button. After assignment procedure, you must click the SAVE button. You can see the live video when you click the live view button as below. When you exit Speco-NVR, you have to input the ID/PW, admin/1234. Details for Speco-NVR can be found in [Speco-NVR User’s Guide].
O2MB1 User ’s Guide 4.2.4. Additional settings through connection to the Admin Page All parameters of the camera are factory default out of the box. For a more sophisticated target application, parameters need to be changed through the admin page. The admin page can be connected through “http://IP_Address:Port_Number/admin.htm” ID and password of the administrator are required. Default ID and password are “admin”, “1234”.
O2MB1 User ’s Guide 5. Trouble Shooting 5.1. No power is applied In case of Standard PoE (Power over Ethernet) Power supply through standard PoE is possible only when the following conditions are met. 1. Standard PoE is supported on the product. 2. The LAN switch supports standard PoE. Make sure that both the IP camera and the LAN switch support standard PoE (IEEE 802.3af) In case of DC adaptor If PoE is not applied, the power and network connection should be made through separate cables.
O2MB1 User ’s Guide 5.2. Cannot connect to the Video Check the status of the network connection through PING test. Try the following on your PC : - Start > Run > Cmd > Ping IP address (Ex : Ping 172.16.42.51) - If “Reply from ~” message is returned (① in the figure below), the network connection is in normal state. Try connection to the video again. If the problem persists, or refer to other trouble shooting notes. - If “Request timed out” message is returned.
O2MB1 User ’s Guide 5.3. Windows Vista or Windows 7 Windows Vista and Windows 7 users need to configure UAC (User Access Control) and Privilege Level for proper recording and still video capture in Speco-NVR and Web Viewer. 1. UAC (User Access Control) configuration 1) Double-click “User Accounts” in control panel 2) Double-click “Turn User Account Control on or off” 3) Uncheck “Use UAC to help protect your computer” 2.
O2MB1 User ’s Guide 1. UAC (User Access Control) configuration 1) Double-click “User Accounts” in control panel 2) Double-click “Change User Account Control setting” 3) Set to “Never notify” Rev.1.2 (Apr.
O2MB1 User ’s Guide 2. Privilege Level Control 1) Select “NVR” icon on the desktop 2) Click right mouse button and select “properties” 3) Check “Privilege Level” in “Compatibility” tab Rev.1.2 (Apr.
O2MB1 User ’s Guide 5.4. Technical Assistance If you need any technical assistance, please contact your dealer. For immediate service please provide the following information. 1. Model name 2. MAC address and Registration number 3. Purchase date 4. Description of the problem 5. Error message Rev.1.2 (Apr.
O2MB1 User ’s Guide Appendix A – Important Notice in Exchanging SD Card (Micro SD) SD Card is a non-volatile memory device for storing video and audio data on the product. Continued writing to the SD Card will cause wear-off of the memory cell. When you plug out the SD Card for replacement or other purpose, follow the steps below in order to prevent data loss or crash of the SD Card. 1. Press factory default button for 1 sec to unmount the SD Card .
