INSTRUCTION MANUAL 2MP TVI LPR Camera HLPR1G (IR Bullet Camera) Speco Technologies is constantly developing product improvements. We reserve the right to modify product design and specifications without notice and without incurring any obligation. EN771T IMX323_speco LPR.indd 1 Rev.
Contents ◑ Contents....................................................... 2 ◑ Precautions.................................................. 3, 4 ◑ Safety Instructions....................................... 5 ◑ Package Contents........................................ 6 ◑ Camera Installation...................................... 7-9 ◑ Specifications............................................... 10 ◑ Camera Dimension...................................... 11 ◑ Features........................................
Precautions Do not install the camera in extreme temperature conditions. Only use the camera under conditions where temperatures are between -10°C and +50°C. Be especially careful to provide ventilation when operating under high temperatures. Never keep the camera pointed directly at strong light. It can cause malfunctions to occur. Do not install the camera under unstable lighting conditions. Severe lighting change or flicker can cause the camera to work improperly.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER(OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. ISO14001 The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Safety Instructions Precautions for use ◑ This camera should be installed by qualified personnel only ◑ There are no user serviceable parts inside ◑ Do not disassemble this camera other than to make initial adjustments ◑ Use a UL approved regulated 24 volt AC or 12 volt DC power supply ◑ Use appropriate low voltage power cable to prevent fire or electrical shock ◑ Please insure that your installation area can support the weight of the camera Please handle this camera carefully : ◑ Do not use a stron
Package Contents Please make sure that the following items are included in the Package: 1) HLPR1G Included Junction Box 1 Power Jack 1 Mount Base Sticker 1 Wrench Set Screw - 3 Tapping Screws 4x25 - 4 Hexagon Socket Screws M4x14 - 3 Plastic Anchor ● ● ● ● -6- EN771T IMX323_speco LPR.
Camea Installation -7- EN771T IMX323_speco LPR.
Camea Installation Compatibility 1) HLPR1G INTCM -8- EN771T IMX323_speco LPR.
Camea Installation 1. HLPR1G WALL ANCHOR, WHT, 6X30, PLASTIC, 4EA JUNCTION BOX SCREW-TAP, SLV, SUS, BH_4X25, TP1, 3EA SCREW-MS, WHT, SUS, PH_M4X10, 3EA SCREW-MS, WHT, SUS, PH_M4X14, 4EA -9- EN771T IMX323_speco LPR.
2MP TVI LPR Camera 5-50mm Motorized Lens ■ HLPR1G (5-50mm) ● 5-50mm motorized auto iris varifocal lens, (10x auto focus / zoom) ● High-contrast imaging performance that delivers sharp, clear license-plate captures ● Full HD 1080p over coax (HD-TVI) ● Supports full UTC control over coax for Zoom / Focus and camera's OSD ● Captures license plates up to 40 mph ● IP66 compliant, weather resistant SPECIFICATIONS MODEL Sensor type Image sensor Effective pixels Total pixels Analogue Resolution Frame rate Scann
Camera Dimension 1) HLPR1G 9” 3.4” 3.74” - 11 - EN771T IMX323_speco LPR.
General Features ● Transfer Video Interface The combination of a 2Mega CMOS image sensor and TVI DSP provides an excellent resolution of TVI picture. ● DNR Smart DNR prevents the image blurring of moving object and activates only if moving objects are appearing on the scene. ● Smart-IR No saturation image, vivid image in darkness! "TVI" camera makes very sharp video image in darkness! This technology eliminates saturation of video image of the closer object in darkness by control of the IR sensitivity.
How to Set Up the camera menu ● Setup Menu MENU MENU SETUP AF MODE AUTO/MANUAL SCANNING HALF/FULL 1.2MOTOR ONEPUSHAF ON-PUSHING SYNC TDN OFF/ON INITIAL ON-PUSHING RETURN (LEFT,RIGHT PUSH : EXIT----SAVE/EXIT----CANCEL) BRIGHTNESS 0~20 default : 10 AUTO NORMAL/DEBLUE SHUTTER MANUAL 1/30, 1/60, 1/120, 1/240, 1/480, 1/1000, 1/2000, 1/4000, 1/8000, 1/15000, 1/30000 2.
How to Set Up the camera menu ● Setup Menu LED LEVEL 0~10 default : 10 D -> N THRES 0~20 default : 8 N -> D THRES 0~20 default : 15 DELAY LOW, MIDDLE, HIGH RETURN (LEFT,RIGHT PUSH : EXIT----SAVE/EXIT----CANCEL) AUTO/AWB/AWC-SET ↓ C-TEMP 3000K/5000K/8000K 5.WHITE BAL R-GAIN 0~20 default : 10 MANUAL B-GAIN 0~20 default : 10 RETURN (LEFT,RIGHT PUSH : EXIT----SAVE/EXIT----CANCEL) 6.DNR OFF/LOW/MIDDLE/HIGH 0 ~ 10 default : 10 SHARPNESS COLOR GAIN 0 ~ 10 default : 10 0.45, 0.5, 0.55, 0.6, 0.65, 0.7, 0.
Menu Set Up Menu setting can be selected by the button inside the camera. 1. Press the set button. * The Set Up menu will be displayed on the monitor. MENU SETUP 1.2MOTOR 2.EXPOSURE 3.BACKLIGHT 4.DAY&NIGHT 5.WHITE BAL 6.DNR 7.IMAGE 8.SYSTEM 9.EXIT OFF B&W AUTO OFF 2. Move and select the required function using the Up and Down button. * Move the triangular indicator Up or Down to select the desired feature by pressing the Up or Down button. MENU SETUP 1.2MOTOR 2.EXPOSURE 3.BACKLIGHT 4.DAY&NIGHT 5.
3. Change menu settings using the Left or Right button. * Available values or Status are displayed by pressing the Left or Right buttons. Press the button until desired value / status is displayed. 4. After Changing the setting move the arrow indicator to EXIT and press the SET button to EXIT. NOTE * Move to the available submenu by moving arrow to desired feature. * Submenu is not available when this symbol displayed “---“. 2MOTOR 1.
1. 2MOTOR AF MODE AUTO SCANNING HALF ONEPUSHAF ON SYNC TDN OFF INITIAL ON RETURN ◆ AF MODE - AUTO : Adjust zoom and focus automatically. - MANUAL : Adjust zoom and focus manually. ◆ SCANNING - HALF : Adjust auto focusing when lens focus fixed. If lens focus is not fixed well, adjust focus manually. - FULL : Scanning full size of scree and adjust autofocusing. ◆ ONEPUSHAF : If you press OSD button 3~4 seconds, focus will be fixed automatically. ◆ SYNC TDN : It can adjust switching time between Day&Night.
2. EXPOSURE BRIGHTNESS 10 IIIIIIIIIIIIIIIIIII| SHUTTER AUTO SENS-UP X16 AGC 10 IIIIIIIIIIIIIIIIIII| RETURN ◆ BRIGHTNESS : The brightness can be adjusted. The brightness control range is 1~20. ◆ SHUTTER : Select one of AUTO/MANUAL/FLICKER to adjust the electronic shutter speed. MANUAL mode can adjust shutter speed 1/30~1/3,0000. → FLK : Select FLK mode if flickering occurs ; caused by the unmatched frequency of electric light.
MENU SETUP 1.2MOTOR 2.EXPOSURE 3.BACKLIGHT 4.DAY&NIGHT 5.WHITE BAL 6.DNR 7.IMAGE 8.SYSTEM 9.EXIT OFF B&W AUTO OFF ◆ Off : Deactivated status. ◆ HLC : This function is used to surpress or strong light source (for example, headlights of cars during nighttime) so that other subjects can be seen in more detail. If you select HCL, a submenu appears where you can make finer adjustments. - LEVEL : Adjust the brightness level from which on the light source is to be masked out. 0~20 level adjustable.
◆ WDR : The WDR (Wide Dynamic Range) function works to correct excessive light within the frame to produce a usable image. When the image has simultaneous bright and dark areas, it makes both areas distinct. If you select WDR, a submenu appears where you can make finer adjustments. -MODE[NORMAL/ROI] can be selected. WDR MODE WEIGHT RETURN NORMAL MIDDLE - ROI WINDOW ZONE [0~3] WINDOW USE [ON/OFF] H-POS [1~1920] : You can select the horizontal starting position of the monitoring area.
◆ AUTO : Automatically, It shifts into the color mode in the bright environment and the B/W mode in the low light condition. It can adjust the delay time, starting brightness and end brightness according to the ambient conditions by pressing the Set button. - D>N THRES : 0~20 CDS THRES level adjustable. - N>D THRES : 0~20 CDS THRES level adjustable. - DELAY [LOW/MIDDLE/HIGH] : Set the delay time for switching between COLOR and B/W. ◆ COLOR : Making the video output color always.
◆ AUT0 : Use this mode when the color temperature is from 3,000k to 8,000k. ◆ AWB : The function to search for the color which is matched well with the ambient environment. ◆ AWC→SET : After letting camera focus on the blank white paper to the best condition of current lighting environment, press the SET button. If the lighting condition is changed, Re-adjustment should be needed. ◆ MANUAL : Manual compensation make the more detailed control possible.
IMAGE When selecting, the following submenu will appear. MENU SETUP 1.2MOTOR 2.EXPOSURE 3.BACKLIGHT 4.DAY&NIGHT 5.WHITE BAL 6.DNR 7.IMAGE 8.SYSTEM 9.EXIT OFF B&W AUTO OFF Here you can optimise the image quality by adjusting different options. 7. IMAGE SHARPNESS 10 IIIIIIIIIIIIIIIIIII| COLOR GAIN 10 IIIIIIIIIIIIIIIIIII| GAMMA 0.5 MIRROR OFF FLIP OFF ACE OFF DEFOG OFF PRIVACY OFF RETURN ◆ SHARPNESS [1 ~ 10] : Adjusts the image sharpness.
◆ PRIVACY [ON, OFF] : This is used to hide certain areas on the monitor. You can designate each different 16 area. The size of a designated area can be adjusted. The color of a privacy area can be selected various colors. When you select the return, the setting values in this function menu are saved, then get out of this menu.
MENU SETUP 1.2MOTOR 2.EXPOSURE 3.BACKLIGHT 4.DAY&NIGHT 5.WHITE BAL 6.DNR 7.IMAGE 8.SYSTEM 9.EXIT OFF B&W AUTO OFF 8.SYSTEM OUTPUT FRAME RATE FREQ IMAGE RANGE LANGUAGE CAM TITLE RESET RETURN TVI 1080_30P 60HZ FULL ENG OFF ON ◆ OUTPUT : TVI - Y GAIN [0~32] : The more higher level, The more brighter image it is. - CB GAIN [0~255] : The more higher level, The more bluer image it is. - CR GAIN [0~255] : The more higher level, The more redder image it is.
◆ CAM TITLE [ON/ OFF] : It can be adjusted when you get into the Cam Title menu. This function is to display the letters of the camera on the monitor. The 15 camera titles can be displayed and the location of the camera title on the screen can be adjusted. Move the triangular indicator to CAMERA ID using the Up and Down button on the Setup menu and then Set to On using the Left or Right button.
Trouble Shooting PROBLEM Nothing appears on the screen. POSSIBLE CAUSE ☞Check the power cable, power supply output and video connection between the camera and monitor. The image on the screen is dim. ☞Are the camera lens or the lens glass dirty? Clean the lens / glass with a soft clean cloth. ☞Adjust the monitor controls, as required. ☞If the camera is facing a very strong light, change the camera position. ☞Adjust the lens focus. The image on the screen is dark.
EN771T IMX323_speco LPR.
EN771T IMX323_speco LPR.
EN771T IMX323_speco LPR.
EN771T IMX323_speco LPR.
200 New Highway Amityville, NY 11701 631-957-8700 1 800 645 5516 www.specotech.com EN771T IMX323_speco LPR.
