VM22TSLCD User’s Manual Speco Technologies 200 New Highway Amityville, NY 11701 800-645-5516 www.specotech.
PRECAUTION The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of insulated dangerous Voltage within the product’s enclosure that may be sufficient magnitude to constitute risk of electrical shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in the literature accompanying the appliance.
8. Damage Requiring Service – The unit should be serviced by qualified service personnel when: The power cord or the plug has been damaged; or Objects have fallen or liquid has been spilled into the unit; or the unit has been exposed to rain or water; or The unit does not appear to operated normally or exhibits a marked change in performance; or The unit has been dropped, or the enclosure damaged. 9. Replacement Parts – Use only manufacturer specified parts.
Touch Panel LCD: Key define AUTO: Auto-optimize displaying picture under PC mode. Enter: This “ Auto” Button can be either “Enter” function in OSD Menu) MENU: OSD menu ON / OFF control. (EXIT Item) ADJUST: Increase or decrease the value on OSD menu. Up: Increase value or turn ON / OFF function. Down: Decrease value or turn ON / OFF function SOURCE: Select input signal from AV1, AV2, S-Video or VGA (PC). POWER: Monitor power ON / OFF. At OFF mode, monitor will be at standby status.
Touch Panel LCD: Connection define ① 1. VGA input 2. DVI input 3. PC audio in 4. VIDEO1 In: Video input Out: Video loop output ② S-VIDEO:Y/C input Audio: 5. 6. Audio input VIDEO2 In: Video input Out: Video loop output Audio: Audio input Port 1 / Port 2 (Touch setting) RS-485 connector Single mode – PTZ to port 1 / DVR to port 2 Matrix mode – Matrix to port 2 7. RS-232 PC control interface 8.
Touch Panel LCD: OSD-Video Setting Brightness: Adjusts the overall picture shade and brightness. Contrast: Permits adjustment of contrast between light and dark areas of the picture. Saturation: Adjusts the intensity of the color. Hue: To determine the lightness and colorfulness of the picture. Sharpness: Sets the desired sharpening enhancement to the picture. Dynamic Contrast: To determine the luminosity of motions of an object Image H Position: Allows adjustment for horizontal position.
Touch Panel LCD: OSD-DVI(VGA) Setting Brightness: Adjusts the overall picture shade and brightness. Contrast: Permits adjustment of contrast between light and dark areas of the picture. Auto Adjustment: Picture adjustment automatic correction, like clock and phase. Image H Position: Allows adjustment for horizontal position. Image V Position: Allows adjustment for vertical position. Phase: Is used to adjust best picture quality. It adjusts the sampling phase across one pixel time.
Touch Panel LCD: OSD-Audio Setting Volume: Controls built-in speakers’ output volumes. Bass: Adjusts the tone to low frequency part of the sound. Treble: Adjust the high or acute of the sound. Balance: Adjusts the softness of loudness of notes in the sound. Mute: To disable the audio function. To enable, press MUTE again.
Touch Panel LCD: OSD-PIP Setting PIP Mode: This function allows the PIP mode to be selected. PIP Source: This function allows the source of the PIP to be selected. PIP Swap: This function allows the position of PIP to be exchanged. POP Zoom: Only Operate under POP (Side By Side) mode. PIP Auto Close: Detect PIP mode signal. PIP Switching: Enable PIP source switching. Switching Time: Control PIP source switching time. User H-Position: Allows adjustment for horizontal position.
Touch Panel LCD: System Setting Aspect Ratio: To change the display mode. Auto Source Detection: The monitor will auto detect the video source when power ON. Color Temperature: Selects color temperature of either 6500°K or 9300°K. Channel Display: This function is to allow the channel title to be displayed on the monitor. Language: English. Power On Control: This function is to assign a specific video signal when power on.
Touch Panel LCD: OSD-Touch Setting Left Hander: Left hander mode control. Set to ON, left hander / Set to OFF, right hander Touch Function Source: Touch mode under AV1 / AV2 / AV1:AV2. Select AV1:AV2, user can touch the AV1 or AV 2 block icon to switch AV1 or AV2 source. 4:3 Mode: LCD display ratio always 4:3 and touch icon table is always on. Number Page Transparency: 0 ~ 100 Control Mode: Single mode / Matrix mode select Speed Dome protocol: Pelco-P / Pelco-D select.
Control mode SINGLE mode: Only one control keyboard in the system. Single mode can be includes these systems below.
PTZ control mode - Single mode 1. Touch any position on the panel 2. Touch number page button into number table 3.
PTZ control with number table Touch Icon Icon Mode Notice CAM: 000 Camera ID Call camera ID status DVR: 000 DVR ID Call DVR ID status MON: 000 Monitor ID Call monitor ID status AV 1 Channel 1 Video 1 input source display AV 2 Channel 2 Video 2 input source display ID(number) ~ ID + Set / ID + Call ID + Clear ESC Cancel ID cancel Enter Confirm ID confirm Call PTZ / Camera ID + Key lock Touch key button protection count to 3 seconds to key lock mode Call DVR ID + Call Only
PTZ Preset Function ID corresponding table Preset ID ID + Call 33 180 degree rotating 34 Speed dome return to zero 76 Start auto pan ID + Set count to 3 seconds 92 Set line scan left stop 93 Set line scan right stop 95 Speed dome OSD Menu 96 Stop line scan 99 Start line scan Pan / Tile Control Mode: Center / Finger.
DVR control mode - Single mode 1. Touch any position on the panel 2. Touch number page button into number table 3.
Extension page Touch Icon Icon Mode Notice CAM: 000 Camera ID Call camera ID status DVR: 000 DVR ID Call DVR ID status MON: 000 Monitor ID Call monitor ID status AV 1 Channel 1 Video 1 input source display AV 2 Channel 2 Video 2 input source display Up Direction button DVR OSD item select Zoom/Enter Digital zoom / Enter DVR image x2 zoom / Enter fun.
DVR control with number table Touch Icon Icon Mode Notice CAM: 000 Camera ID Call camera ID status DVR: 000 DVR ID Call DVR ID status MON: 000 Monitor ID Call monitor ID status AV 1 Channel 1 Video 1 input source display AV 2 Channel 2 Video 2 input source display ID(number) ~ ID + Full button to DVR full screen ESC Cancel ID cancel Enter Confirm ID confirm Call PTZ / Camera ID + Key lock Touch key button protection count to 3 seconds to key lock mode Call DVR Call Monitor
