INSTRUCTION MANUAL Intense-IR Camera CVC5715DNV CVC5715DNVW
◑ Contents...................................................... 1 ◑ Precautions ................................................. 2, 3 ◑ Safety Instructions ...................................... 4 ◑ Package Contents....................................... 5 ◑ Camera Installation ..................................... 6-8 ◑ .............................................. 9 ◑ Camera Dimension ..................................... 10 ◑ OSD Menu Details ......................................
Only use the camera under conditions where temperatures are between -10°C and +50°C. Be especially careful to provide ventilation when operating under high temperatures. It can cause malfunctions to occur. Severe lighting change or flicker can cause the camera to work improperly. Severe lighting change or flicker can cause the camera to work improperly. This is one of the most important parts of the camera. Be careful not to leave fingerprints on the lens cover.
CAUTION CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN RISK OF ELECTRIC SHOCK RISK OF DOELECTRIC NOT OPENSHOCKCAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT OPEN DO NOT REMOVE COVER(OR BACK). CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK USER-SERVICEABLE PARTS INSIDE. CAUTION:TO REDUCE THE RISK OF ELECTRIC NO SHOCK DO NOT REMOVE COVER(OR BACK). DO NOT REMOVE COVER(ORREFER BACK).SERVICING TO QUALIFIED SERVICE PERSONNEL. NO USER-SERVICEABLE PARTS INSIDE. NO USER-SERVICEABLE PARTS INSIDE.
◑ ◑ There are no user serviceable parts inside ◑ Do not disassemble this camera other than to make initial adjustments ◑ Use a UL approved regulated 24 volt AC or 12 volt DC power supply rical shock ◑ ◑ Please insure that your installation area can support the weight of the camera ◑ Do not use a strong or abrasive detergent when cleaning the camera ◑ Do not install near cooling or heating device 4
Package Contents Please make sure that the following items are included in the Package: 1) CVC5715DNV, CVC5715DNVW • 1 Video Test Connector, Power Jack • 1 2Axis Bracket Adaptor • 2 Wrenches • Set Screw - 4 Tapping Screws 4x20 - 4 Hexagon Socket Screws M4x7
CAMERA INSTALLATION Compatibility 1) CVC5715DNV, CVC5715DNVW INTCM
CAMERA INSTALLATION 1.
Intense - IR Bullet Camera DC Auto Iris Varifocal Lens(4mm-9mm) / IR LED Built-in 14pcs ■ CVC5715DNV ■ CVC5715DNVW 600TV Lines DC Auto Iris Varifocal Lens (4mm-9mm) True Day/Night Capability ICR-IR Cut Filter Removable 850nm IR LEDs * 14pcs IR LED's 14EA & Heater's 2EA SPECIFICATIONS MODEL Sensor Total Pixels Effective Pixels Scanning System Synchronization O.S.D Backlight Resolution S/N (Y signal) Min.
CAMERA INSTALLATION 1) CVC5715DNV, CVC5715DNVW 7.63” 2.71” dia 4.64” 2.59” 2.71” 2.87” 7.
O S D C o n t r o l B u t t o n 1. Type A, Type B, Type C of OSD button could be used when it needs to OSD control. 2.
H o w t o S e t U p t h e c a m e r a m e n u ● S e t u p M e n u 12
13
14
Menu Set Up Menu items can be selected by using the OSD buttons of the camera 1. Press the Set Up button. * The Set Up menu will be displayed on the monitor. SETUP 1.LENS 2.EXPOSURE 3.WHITE BAL 4.DAY / NIGHT 5.3DNR 6.SPECIAL 7.ADJUST 8.RESET 9.EXIT DC ATW COLOR ON 2. Move and select the required function using the Up and Down button. * Move the arrow indicator Up or Down to select the desired feature by pressing the Up or Down button. SETUP 1.LENS 2.EXPOSURE 3.WHITE BAL 4.DAY / NIGHT 5.3DNR 6.SPECIAL 7.
3. Change menu settings using the Left or Right button. * Available values or Status are displayed by pressing the Left or Right buttons. Press the button until desired value / status is displayed. 4. After Changing the setting move the arrow indicator to EXIT and press the SET button to EXIT. NOTE * Move to the available submenu by moving arrow to desired feature. * Submenu is not available when this symbol is display "- - - -" Lens 1.
NOTE * When DC is selected, the brightness can be adjusted. The brightness control range is 1 ~ 100. Lens BRIGHTNESS RETURN 100 3. Press the RETURN to return to the SETUP menu. Exposure This function is used to select Automatic or Manual shutter speed control. 1. On the Set Up menu screen select EXPOSURE by using the Up or Down button. 2. Select the desired shutter mode by pressing the Left or Right button. SETUP 1.LENS 2.EXPOSURE 3.WHITE BAL 4.DAY / NIGHT 5.3DNR 6.SPECIAL 7.ADJUST 8.RESET 9.
EXPOSURE SHUTTER AGC SENS-UP BLC D-WDR RETURN AUTO MIDDLE AUTO OFF OFF RET NOTE *Shutter: Select Shutter using the Up or Down button, you can adjust the shutter speed from 1/60, FLK, 1/250~1/100,000. →FLK: Select FLK mode if flickering occurs; caused by the unmatched frequency of electric light. If select FLK mode, sense-up does not operate. * AGC(AUTO GAIN CONTROL): A higher gain increases brightness but also increases any noise.
* RETURN: Select Return to save the changes in the EXPOSURE menu and retun to the SETUP menu. NOTE * Pressing the SET button in AUTO mode allows adjustment of image brightness by increasing or decreasing the shutter speed (x2 ~x256). * The higher the level, the brighter the image becomes, but it is possible that an after image (ghosting) could appear. * When SENS-UP is activated the increased magnification can induce noise and pixelation; this is quite normal.
POSITION SIZE PICTURE 1 PICTURE 2 * HSBLE: HSBLC function is especially effective for reading car number plates at the night time. You can select and define the required observation area for the target object and ignore a strong light area. Press the "ENTER" button at the AREA menu, you can change the position as shown in Picture 1. Press the "ENTER" button again after area setting, you can change the position as shown in Picture 2. Default: Press the Default to return to factory defaults.
HSBLC OFF HSBLC ON * D-WDR: This camera which is using 3D-DNR DSP provides intelligent light level control to overcome even strong backlight conditions. →OFF: D-WDR function does not operate. When there are simultaneous bright & dark image area WDR makes them both distinct and can be selected as OUTDOOR and INDOOR. D-WDR LOW-LEVEL 5 HIGH-LEVEL 5 RETURN RET D-WDR OFF D-WDR ON * RETURN: Select Return to save the changes in the EXPOSURE menu and return to the SETUP menu.
White Balance The White Balance function is used to control the “on-screen” colors. 1. Move the arrow indicator to WHITE BAL on the SETUP menu screen using the Up and Down button. 2. Select the desired mode by using the Left or Right button. SETUP 1.LENS 2.EXPOSURE 3.WHITE BAL 4.DAY / NIGHT 5.3DNR 6.SPECIAL 7.ADJUST 8.RESET 9.EXIT DC ATW COLOR ON * There are three user selectable White Balance settings available.
Day / Night Picture can be displayed in either colour of black and white. 1. Select DAY / NIGHT using the Up or Down button on the SETUP menu screen. SETUP 1.LENS 2.EXPOSURE 3.WHITE BAL 4.DAY / NIGHT 5.3DNR 6.SPECIAL 7.ADJUST 8.RESET 9.EXIT DC ATW AUTO ON 2. Select the desired mode using the Left and Right buttons. * COLOR : The picture is always displayed in color. * BW : This picture is always displayed in black and white. Select BW using the button and press the menu to activate COLOR BURST option.
IR SMART GAIN 10 SIZE AREA RETURN RET AREA SMART IR OFF SMART IR ON → AUTO: The mode will automatically switches to COLOR in normal condition and switches to BW mode when ambient illumination is low. Press the SET button to set the switching time or D→N(AGC), N→D(AGC) in AUTO mode.
3DNR 3DNR is used to reduce the level of background noise in a low luminance environment. 1. Move the arrow indicator to 3DNR by using the Up and Down button. SETUP 1.LENS 2.EXPOSURE 3.WHITE BAL 4.DAY / NIGHT 5.3DNR 6.SPECIAL 7.ADJUST 8.RESET 9.EXIT DC ATW AUTO ON 2. Select whether or not to activate 3DNR by using the Left and Right buttons. * ON: Activates 3DNR - Digial noise reduction can be adjusted between 0 ~ 100. * OFF: Deactivates 3DNR - noise is not reduced.
Special When the SETUP menu screen is displayed, select SPECIAL using the Up and Down buttons. SETUP 1.LENS 2.EXPOSURE 3.WHITE BAL 4.DAY / NIGHT 5.3DNR 6.SPECIAL 7.ADJUST 8.RESET 9.EXIT DC ATW AUTO ON Select one of the mode using the Up and Down button. SPECIAL 1. CAM TITLE OFF 2. D - EFFECT 3. MOTION OFF 4. PRIVACY OFF 5. DEFECT 6. RETURN RET 1. CAM TITLE : When input, the Camera ID is displayed on the monitor.
NOTE * When CAMERA TITLE is set to OFF, the CAMERA TITLE is not displayed on the monitor. 1-3) Press the SETUP button. CAMERA TITLE 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ ▷ → ← ↑ ↓ ( ) ㅡ_□ / = & : ~ , . ← → CLR POS END 1-4) The CAMERA TITLE can be up to 15 alphanumeric characters in length. ① Move the cursor to choose an alphanumeric character. CAMERA TITLE 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ ▷ → ← ↑ ↓ ( ) ㅡ_□ / = & : ~ , .
NOTE * In cases where the wrong Camera ID has been input........ Move the cursor to CLR and press SETUP button to erase characters from left to right, and repeat the above steps to input the characters again. 1-5) To select the position where the Camera ID should be displayed on the screen. ① Move the cursor to POS and press the SET button. CAMERA TITLE 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ ▷ → ← ↑ ↓ ( ) ㅡ_□ / = & : ~ , . ← → CLR POS END ② Created camera ID is displayed.
③ Select a new position by using the four CAM1 directional button, Press the SET button to confirm the position. 2. D - EFFECT Move the cursor to D-EFFECT and press the SET button to set the other image functions. D-EFFECT FREEZE OFF MIRROR OFF D-ZOOM OFF RETURN RET 2 -1) MIRROR : Flip the image horizontally on the screen.
* V-FLIP : Flip the image vertically on the screen. * ROTATE : Flip the horizontal image vertically on the screen. * OFF : Disabled. MIRROR ON MIRROR OFF 2-2) D - ZOOM: Digital zoom available, range x1 ~ x32. PAN : The pan range can be controlled between -10 ~ + 100 TILT : The tilt range can be controlled between -10 ~ + 100 D-ZOOM D-ZOOM X 10 PAN TILT RETURN RET NOTE * PAN and TILT function should be available when using the digital zoom.
2-3) GAMMA : Desired gamma values can be adjusted between 0.05 ~ 1.00. 2-4) NEG. IMAGE : ON : Activates negative image just like film OFF : Normal image 2-5) RETURN : Move the arrow indicator to RETURN after complete the setup to return to SPECIAL menu. 3. MOTION MOTION AREA SELECT AREA DISPLAY SENSITIVITY MOTION VIEW RETURN AREA1 ON 40 OFF RET POSITION SIZE 3-1) When the special menu screen is displayed, use the Up or Down button to access the MOTION menu.
4. PRIVACY Hide an area you want to hide on the screen. 4-1). When the SPECIAL menu screen is displayed, press the Up and Down buttons to set to PRIVACY. PRIVACY AREA SELECT AREA DISPLAY COLOR RETURN AREA1 ON 15 RET POSITION SIZE 4-2). Set up the area mode using the 4 direction buttons. AREA SELECT : You can select up to 8 MD area.
③ Move the arrow indicator to WIDTH to make desired width of cells to increase or decrease by using the Left / Right button between the level 0 ~ 100. ④ Move the arrow indicator to HEIGHT to make desired height of cells to increase or decrease by using the Left / Right button between the level 0 ~ 100. ⑤ Move the arrow indicator to the LEFT / RIGHT and TOP / BOTTOM to select the desired area positon by using the LEFT or RIGHT button.
ADJUST 1. When the SETUP menu screen is displayed, select ADJUST using the Up and Down buttons. SETUP 1.LENS 2.EXPOSURE 3.WHITE BAL 4.DAY / NIGHT 5.3DNR 6.SPECIAL 7.ADJUST 8.RESET 9.EXIT DC ATW AUTO ON 2. Select the desired mode by using Up or Down button. ADJUST 20 SHARPNESS MONITOR RETURN LCD RET SHARPNESS : Improving image clarity. The level can be adjusted to obtain an improved image. However, when the level is set too high it can distort the image or cause noise.
RESET Resets the camera settings to the factory defaults. SETUP 1.LENS 2.EXPOSURE 3.WHITE BAL 4.DAY / NIGHT 5.3DNR 6.SPECIAL 7.ADJUST 8.RESET 9.EXIT RESET DC FACTORY RETURN ATW AUTO ON RET EXIT Press the SET button in the EXIT menu to save the current settings and exit the SETUP menu. SETUP 1.LENS 2.EXPOSURE 3.WHITE BAL 4.DAY / NIGHT 5.3DNR 6.SPECIAL 7.ADJUST 8.RESET 9.
Trouble Shooting P R O B L E M Northing appears on the screen. P O S S I B L E C A U S E ☞Check the power cable, power supply output and video connection between the camera and monitor. ☞Are the camera lens or the lens glass dirty? The image on the screen is dim. Clean the lens / glass with a soft clean cloth. ☞Adjust the monitor controls, as required. ☞If the camera is facing a very strong light, change the camera position. ☞Adjust the lens focus. The image on the screen is dark.
37
- MEMO - 38
- MEMO - 39
200 New Highway Amityville, NY 11701 631-957-8700 1 800 645 5516 www.specotech.
