INSTRUCTION MANUAL 650Line Intensifier3™ Series HT7246IHR / HT7247IHR / HT7250IHR (Weatherproof Dome Camera with Chameleon™ Cover) HTINTB8 / HTINTB9 / HTINTB10 (Weatherproof Bullet Camera with mount plate) HTINTD8 / HTINTD9 / HTINTD10 (Weatherproof Dome Camera) HT647HRTP (Miniature Weatherproof Dome Camera with Chameleon™ Cover) CVC6245IHR (Indoor Wall & Ceiling Mount Dome Camera) CVC6246IHR (Indoor Wall & Ceiling Mount Dome Camera) HTINTT5 (Traditional Box type Camera) Speco Technologies is consta
Contents ◑ Contents....................................................... 1 ◑ Precautions.................................................. 2, 3 ◑ Safety Instructions....................................... 4 ◑ Package Contents........................................ 5 ◑ Camera Installation...................................... 6-13 ◑ Specifications............................................... 14-20 ◑ Camera Dimension...................................... 21-23 ◑ Features.................................
Precautions Do not install the camera in extreme temperature conditions. Only use the camera under conditions where temperatures are between -10°C and +50°C. Be especially careful to provide ventilation when operating under high temperatures. Never keep the camera pointed directly at strong light. It can cause malfunctions to occur. Do not install the camera under unstable lighting conditions. Severe lighting change or flicker can cause the camera to work improperly.
CAUTION CAUTION RISKOF OFELECTRIC ELECTRICSHOCK SHOCK RISK DONOT NOTOPEN OPEN DO CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION:TO CAUTION:TOREDUCE REDUCETHE THERISK RISKOF OFELECTRIC ELECTRIC SHOCK REDUCE THE RISK OF ELECTRIC SHOCK CAUTION:TO SHOCK DO NOT REMOVE COVER(OR BACK). DONOT NOTREMOVE REMOVECOVER(OR COVER(ORBACK). BACK). DO NO USER-SERVICEABLE PARTS INSIDE. NO USER-SERVICEABLE PARTS INSIDE. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Safety Instructions Precautions for use ◑ This camera should be installed by qualified personnel only ◑ There are no user serviceable parts inside ◑ Do not disassemble this camera other than to make initial adjustments ◑ Use a UL approved regulated 24 volt AC or 12 volt DC power supply ◑ Use appropriate low voltage power cable to prevent fire or electrical shock ◑ Please insure that your installation area can support the weight of the camera Please handle this camera carefully : ◑ Do not use a strong
Package Contents Please make sure that the following items are included in the Package: 1) HT7246IHR, HT7247IHR, HT7250IHR • 1 Video Test Connector, Power Jack • 1 Chameleon Cover • 1 Wrench • Set Screw - 3 Tapping Screws 4x40 - 3 Plastic Anchor 2) HTINTB8, HTINTB9, HTINTB10 • 1 Video Test Connector, Power Jack • 1 Bracket Base • 2 Wrenches • Set Screw - 4 Tapping Screws 4x25 - 4 Hexagon Socket Screws 5x10 3) HTINTD8, HTINTD9, HTINTD10 • 1 Video Test Connector, Power Jack • 2 Wrenches • Set Screw - 3 Tappin
CAMERA INSTALLATION jvuulj{Gwv~lyGjhislG XUG~oluG|zpunGXYG}vs{zGkjGOGG\WWGhPG wGpGaylk jGaGORP kjGXY}GwGz YUG~oluG|zpunGY[G}vs{zGhjGO[WG}GhP ylkORP hjGY[} ishjraOTP wGz ZUGjvuulj{G}pklvGjhislG T jvuulj{GiujGjhislG{vG{olGiujGqhjrUG [UGjvuulj{GhGGOy GP T jGORGSGjvtPGGwGGGOTUGjvtPGG uGGGlGhGkGGtG kGG˄vu˅GGGU R wGhGkG jvtG
CAMERA INSTALLATION Compatibility 1) HT7246IHR, HT7247IHR, HT7250IHR INTWM INTPM CVCJBD DFM 2) HTINTB8, HTINTB9, HTINTB10 CVCJBB INTJBS 7 INTCM
CAMERA INSTALLATION Compatibility 3) HTINTD8, HTINTD9, HTINTD10 INTWM INTPM 4) CVC6245IHR, CVC6246IHR DFM 8 JB03TG
CAUTION : The installation instructions in this manual are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. CAMERA INSTALLATION 1.
CAMERA INSTALLATION 2.
CAMERA INSTALLATION 3.
CAMERA INSTALLATION 4.
CAMERA INSTALLATION 5.
650 Line Intensifier3 (Weatherproof Dome Camera with Chameleon™ Cover) DC Auto Iris Varifocal Lens 2.8-12mm / 9-22mm / 5-50mm ■ HT7246IHR (2.
650 Line Intensifier3 (Weatherproof Bullet Camera with mount plate) DC Auto Iris Varifocal Lens 2.8-12mm / 5-50mm / 9-22mm ■ HTINTB8 / HTINTB8W (2.
650 Line Intensifier3 (Weatherproof Dome Camera) DC Auto Iris Varifocal Lens 2.8-12mm / 5-50mm / 9-22mm ■ HTINTD8 / HTINTD8W (2.
650 Line Intensifier3 (Miniature Weatherproof Dome Camera with Chameleon™ Cover) 3.6mm Fixed Board Lens ■ HT647HRTP (3.
650 Line Intensifier3 (Indoor Wall & Ceiling Mount Dome Camera) DC Auto Iris Varifocal Lens 2.8-12mm ■ CVC6245IHR / CVC6245IHRW (2.
650 Line Intensifier3 (Indoor Wall & Ceiling Mount Dome Camera) DC Auto Iris Varifocal Lens 2.8-12mm ■ CVC6246IHR / CVC6246IHRW (2.
650 Line Intensifier3 (Traditional Box type Camera) C&CS Mount Lens ■ HTINTT5 (C&CS Mount Lens) SPECIFICATIONS HTINTT5 MODEL Image Pick-Up Device TV System Total Pixels Effective Pixels Scanning Frequency Scanning System Synchronization Resolution Minimum Illumination S/N Ratio Video Output Electronic Shutter Speed OSD WDR BLC Day & Night Gain Control White Balance Intensify Motion Detection Privacy Masking SPECO DNR Digital Zoom DIS (Digital Image Stabilization) Sharpness Flip / Mirror Power Supply Pow
CAMERA DIMENSION 1) HT7246IHR, HT7247IHR, HT7250IHR 5.10” dia 3.46” 1.16” 5.10” dia 3.93” dia 2) HTINTB8, HTINTB9, HTINTB10 11.02” 3.46” 3.89” dia 3.11” 4.01” 5.90” 5.03” 10.
CAMERA DIMENSION 3) HTINTD8, HTINTD9, HTINTD10 4) HT647HRTP 4.33” dia 3.14” 1.41” 4.33” dia 3.22” dia 22 3.70” 4.36” 3.34” 5.
CAMERA DIMENSION 5) CVC6245IHR, CVC6246IHR 5.51” dia 4.09” 1.25” 5.51” dia 4.60” dia 6) HTINTT5 3.46” 3.26” 1.49” dia 2.20” 2.
FEATURES Now with “PRESETS” PRESETS (Outdoor, Indoor, Elevator, Lobby, Hallway & Low Light) Used for a quick and easy setup for the installation environment. 650TVL Resolution Horizontal resolution of 650 TV lines is achieved by using a SONY Super-HAD CCD with 410,000 pixels, and a custom DSP yielding pictures with a high S/N ratio. INTENSIFIER 3 More Powerful Performance in low light condition. High quality Pictures to be captured in very low light condition.
FEATURES Motion Detection with Alarm Output Built in motion detector with adjustable areas of coverage will Send a signal to an external alarm device when motion is detected. Privacy Mask It also has the ability to mask up to 8 areas of the picture where Viewing is not desired. Each zone can be independently programmed via the OSD Stabilizer This function removes image jitter that is caused by vibrations in the building and reduces the amount of hard drive space.
● Preset Mode SPECO TECH 1.PRESET MODE 2.MAIN SETUP 3.EXIT INDOOR RESET 1. Preset : INDOOR / OUTDOOR / LOW LIGHT / HALLWAY / LOBBY / ELEVATOR. - Used for a quick and easy setup for the installation environment. ● Menu Setup 1. Press the Function Setup switch. - Main setup menu is displayed on the monitor screen. MAIN SETUP 1.LENS 2.EXPOSURE 3.WHITE BAL 4.WDR 5.BACKLIGHT 6.SPECO DNR 7.DAY/NIGHT 8.SPECIAL 9.RETURN DC ATW OFF OFF ON AUTO SAVE 2.
MAIN SETUP 1.LENS 2.EXPOSURE 3.WHITE BAL DC ATW 3. THE Lens mode has sub menu items as listed below. - BRIGHTNESS : Adjusts the video brightness. - FOCUS ADJ : To adjust the DC lens focus correctly, you must activate the Focus Settings mode under each lens menu. Activate the Focus Settings mode, adjust the lens focus, and then deactivate the settings mode. ☞ NOTE ■ If color rolling occurs when using a DC lens, set Shutter to Fixed (---). ● Exposure Setting MAIN SETUP 1.LENS 2.EXPOSURE 3.
☞ NOTE ■ When the SHUTTER is set to MANUAL or A.FLK mode, INTENSIFY will be disabled. ◆ FUTO GAIN CONTROL) : The higher the gain level, the brighter the screen - but the higher the noise. * OFF : Deactivates the AGC function. * LOW : Allows automatic gain control from 5.3dB to 32dB. * HIGH : Allows automatic gain control from 5.3dB to 37dB. ◆ INTENSIFY : When it is night or dark, the camera automatically detects the light level and maintains a clear picture if this mode is activated.
※Select one of the following 5 modes, as appropriate for your purpose. ◆ ATW : Select this when the color temperature is between 1,700˚K and 11,000˚K. ◆ OUTDOOR : Select this when the color temperature is between 1,700˚K and 11,000˚K. (sodium light inclusion) ◆ INDOOR : Select this when the color temperature is between 4,500˚K and 8,500˚K. ◆ MANUAL : Select this to fine-tune White Balance manually. Set White Balance first by using the ATW or AWC mode.
● Backlight Setting Unlike conventional cameras, the 650Line Intensifier3™ Series are designed to deliver a distinctive subject and background at the same time, even when the subject is backlight, by using the features of the proprietary W-V DSP chip. 1. When the SETUP menu screen is displayed, select 'BACKLIGHT' by using the Function Setup switch so that the arrow indicates 'BACKLIGHT'. MAIN SETUP 1.LENS 2.EXPOSURE 3.WHITE BAL 4.WDR 5.BACKLIGHT 6.SPECO DNR 7.DAY/NIGHT 8.SPECIAL 9.
BLC SETUP LEVEL TOP BOTTOM LEFT RIGHT HLC SETUP LOW 38 109 54 121 LEVEL MIDDLE LIMITS NIGHT ONLY MASK COLOR BLACK MASK TONE 1 TOP 5 BOTTOM 120 LEFT 5 RIGHT 172 Press Set to Return Press Set to Return ☞ NOTE ■ Because there can be a difference in the effectiveness of HLC according to the amount of light area in the screen, optimize the installation angle for the best HLC performance. ■ When dark, the HLC is only activated when a bright light exceeding a specific size in NIGHT ONLY mode.
3. Set the SPECO DNR mode to 'ON' and press the Function Setup switch. Then you can adjust the noise reduction level. ☞ NOTE ■ You cannot set the SPECO DNR to ‘ON’ or ‘OFF’ when the AGC mode of the EXPOSURE menu is ‘OFF’. ■ When adjusting the noise reduction level in the SPECO DNR mode, remember that the higher the level set, the more the noise level will be reduced, as will the brightness of the image. ● Day/Night Setting You can display pictures in color or black and white. 1.
◆ AUTO : The mode is switched to 'Color' in a normal environment, but switches to 'B/W' mode when ambient illumination is low. To set up the switching time for AUTO mode, press the Function Setup switch. You can turn on or off the burst signal on B/W mode. - BURST MODE : You can turn on or off the burst signal AUTO SETUP on B/W mode. 1.BURST MODE ON - DURATION : You can select brightness of illumination 2.COLOR→B/W about changing the day/night mode.
2. Select a desired mode using the Function Setup switch. SPECIAL 1.IMAGE ADJ 2.MONITOR 3.CAM TITLE 4.SYNC 5.MOTION DET 6.PRIVACY 7.COMM ADJ 8.LANGUAGE 9.RETURN OFF INT OFF OFF ENGLISH ◆ IMAGE ADJ. : 1) When the SETUP menu screen is displayed, select 'IMAGE ADJ' by using the Function Setup switch so that the arrow indicates 'IMAGE ADJ'. 2) Select a desired mode using the Function Setup switch. IMAGE SETUP 1.V-REV 2.H-REV 3.D-ZOOM 4.DIS 5.FONT COLOR 6.SHARPNESS 7.
☞ NOTE ■ When the V-REV or H-REV mode is enabled, the text on the screen does not flip. ■ If you increase the SHARPNESS level too high, the picture may become distorted or noise may appear. ◆ MONITOR : Please change the settings value of video appropriate to your monitor. 1) LCD : Please select this menu item when using a LCD monitor. 2) CRT : Please select this menu item when using a CRT monitor. 3) USER : Please use this menu item when using a monitor other than standard ones.
- INT : Internal Synchronization Type - L/L : Power Synchronization Type, Line-lock * Press the Function Setup switch. * You can select a desired phase from 0 to 359 when select 'phase'. ☞ NOTE ■ When using AC power at 60Hz(NTSC), 50Hz(PAL), frequency, you can use the L/L type synchronization. ■ When the power is DC 12V, the SYNC menu is fixed to the ‘INT’ mode. ◆ MOTION DET :This product has a feature MOTION DET that allows you to observe movement of 1.
1) When the SPECIAL menu screen is displayed, press the Function Setup switch so that the arrow indicates 'PRIVACY'. 2) Set up the mode using the Function Setup switch. - AREA : You can select up to 12 PRIVACY areas. - MODE : Determines whether to use the area selected in the AREA. - MASK COLOR : Determine area color. You can select Green, Red, Blue, Black, White, Gray. - MASK TONE : Adjust the brightness of MASK COLOR. - TOP/BOTTOM/LEFT/RIGHT :Adjust the size and position of the selected area.
● Trouble Shooting PROBLEM Northing appears on the screen. POSSIBLE CAUSE FCheck the power cable, power supply output and video connection between the camera and monitor. FAre the camera lens or the lens glass dirty? The image on the screen is dim. Clean the lens / glass with a soft clean cloth. FAdjust the monitor controls, as required. FIf the camera is facing a very strong light, change the camera position. FAdjust the lens focus. The image on the screen is dark.
39
uMEMO 40
uMEMO 41
uMEMO 42
200 New Highway Amityville, NY 11701 631-957-8700 1 800 645 5516 www.specotech.
