OWNER’S MANUAL 1
TABLE OF CONTENTS Introduction......................................................................... 4 Post Setup.......................................................................... 6 Frame Features................................................................... 8 Air Pressure Chart (Enduro)................................................. 9 Frame Geometry(Enduro).................................................... 10 Schematic and Specifications (Enduro)..............................
INTRODUCTION Congratulations on your purchase and welcome to the finest line of suspension bikes available! About this Manual This manual is designed to be used in conjunction with the Bicycle Owner’s Manual and owner’s manuals supplied by the manufacturer of the front and rear suspension components. If you did not receive any of these manuals, download them from the Internet, contact your dealer, or contact us by telephone. There may be more current manuals and technical information available.
INTRODUCTION As activities such as racing, jumping, severe off road riding, and stunt riding are extremely dangerous, SAFETY should always be the first consideration. Don’t ride in the race, ride hard off road, try the jump, or do the stunt, UNLESS YOU CAN DO SO SAFELY. Here are some additional recommendations: • Take lessons from a competent instructor first. • Do jumps or stunts only in areas designated for this type of riding.
SEAT POST SETUP SEATPOST MINIMUM EXTENSION: All Specialized full suspension models with interrupted seat tubes have a small hole to identify the minimum extension allowed for your seatpost. If you cannot see the seatpost tube through this hole, your seatpost is too far extended. If a greater saddle height is required, replace the seatpost with a longer one.
! SEAT POST SETUP Warning: Read the following instructions on proper seat post adjustment before riding your Specialized Enduro. Failure to follow these instructions can result in damage to the equipment and rider. ENDURO MODELS On 2002-2004 Enduro models, the interrupted seat tube design is NOT equipped with a seat post insertion limiting stop at the base of the seat tube which allows for a wide range of adjustment for extension and insertion to accommodate certain types of terrain and riding styles.
ENDURO FSR / SX FRAME FEATURES 1. Main Frame 2. Seatstay 3. Chainstay 4. Shock Link 5. Main Pivot 6. Dropout (Horst) Pivot � � � 9. Lower Shock Eyelet 10. Upper Shock Eyelet 12. Replaceable Derailleur Hanger 8 �� � 8. Shock Link at Frame Pivot 11. Shock � � 7.
ENDURO FSR AIR PRESSURE CHART Rider Weight Rider Weight lbs (kg) Air PSI 95-105 (43-47) 75 105-115 (47-52) 85 115-125 (52-57) 95 125-135 (57-61) 105 135-145 (61-66) 115 145-155 (66-70) 125 155-165 (70-75) 135 165-175 (75-80) 145 175-185 (80-84) 155 185-195 (84-89) 165 195-205 (89-93) 175 205-225 (93-102) 185 225-245 (102-111) 205 245-265 (111-120) 225 NOTE: This air chart is designed as a recommended starting point only.
ENDURO FSR FRAME SPECIFICATIONS 1 2 3 4 4 5 5 6 6 7 8 *Top Tube Length **Standover Hgt Head Tube Length Head Tube Angle (Steep) Head Tube Angle (Slack) Seat Tube Angle (Steep) Seat Tube Angle (Slack) BB Height (High) BB Height (Low) Wheelbase Chainstay Length Small (mm) 551 711 100 70.5º 69.5º 69º 68º 336 324 1067 424 Small (in) 21.7” 28.0” 3.94” 70.5º 69.5º 69º 68º 13.23” 12.76” 42.01” 16.7” Medium (mm) 584 711 110 70.5º 69.5º 69º 68º 336 324 1091 424 Medium (in) 23.0” 28.0” 4.33” 70.5º 69.
ENDURO FSR FRAME GEOMETRY � � � � � � � � 11
Schematic #2 2.e 1.c 2.f 1.d 1.h Se s at Shock Link Mount 1.g 1.c 2.e S h o c k L ink tay 1.h 1.d 2.f 2.o 2.h Sh k oc 2 .n 2.k Shock Link 2.m NOTE: Part 2.m Necessary for limited run of 2002 frames only 1.f 1 .b 1.f 2.d 1.e 1. b Dr o p o u t s 1 . f Chainstay 1.b 1.f 1.b 1.f 2.d 1.e 2.c 1.a BB Shell 1.a 2.a 2003-2004 Enduro Model 12 1.e 2.b 1.a 2. g 1.e 1.a 2.
NOTE: Bearing and Bolt Kits are available only through your local Specialized dealer. To retain your warranty and for your safety, all maintenance should be performed by your local Specialized dealer. Bearing Kit Parts Part # Qty. 1.a 1.b 1.c 1.d 1.e 1.f 1.g 1.
ENDURO SX FRAME SPECIFICATIONS 1 2 3 4 4 5 5 6 6 7 *Top Tube Length **Standover Hgt Head Tube Length Head Tube Angle (Steep) Head Tube Angle (Slack) Seat Tube Angle (Steep) Seat Tube Angle (Slack) BB Height (High) BB Height (Low) Chainstay Length Short (mm) 551 711 100 69º 68º 67.5º 66.5º 318 307 424 Short (in) 21.7” 28.0” 3.94” 69º 68º 67.5º 66.5º 12.5” 12.1” 16.7” Long (mm) 584 711 110 69º 68º 67.5º 66.5º 318 307 424 Long (in) 23.0” 28.0” 4.33” 69º 68º 67.5º 66.5º 12.5” 12.1” 16.
ENDURO SX FRAME GEOMETRY � � � � � � � 15
Schematic #7 2.d Shock Link Mount 1.c 1.g 2.e 1.d 1.h 1.c 2.d Shock Link ay st at Se 1.h 1.d 2.e 2.m 2.g 2.k 2.h Shock Link Upper Shock Mount 1.f 1.b 1.f 2.c 1.e 1.b Dropouts 1.f 1.b 1.f 1.b 1.f 16 2.a 1.a Chainstay 2.c 1.e BB Shell 1.a 2.b 2.
NOTE: Bearing and Bolt Kits are available only through your local Specialized dealer. To retain your warranty and for your safety, all maintenance should be performed by your local Specialized dealer. Bearing Kit Parts Part # Qty. 1.a 1.b 1.c 1.d 1.e 1.f 1.g 1.
SBC LIMITED WARRANTY Specialized Bicycle Components, Inc.
USEFUL PRODUCT LIFE CYCLE Every Specialized bicycle and frameset has a useful product life cycle. The length of that useful product life cycle will vary with the construction and materials of the bicycle or frameset, the maintenance and care the bicycle or frameset receives over its useful product life cycle, and the type and amount of use the bicycle or frameset is subject to.
15130 Concord Circle Morgan Hill, CA 95037 www.specialized.
