Brochure
Thermoplastic Valves Product Guide & Engineering Specifictions
Ball Valve Accessories
Made in the U.S.A. Suitable for Oil-Free air handling to 25 psi, not for distribution of compressed air or gas Page 754
Due to Material Cost Variations, Prices Sub
j
ect to Chan
g
e. Check On-line Catalo
g@
www.spearsmf
g
.com
1: Stem Extension does not permit use of Handle Lockout on True Union 2000 Industrial Ball Valves.
• Kits for True Union 2000 Valves and for Regular True
Union, Single Entry or Compact Ball Valves
• Simple 2-Piece Kit for use with existing Valve Handle
and Schedule 80 pipe, or can be ordered factory
assembled to desired length as 1-piece unit.
• Kit includes 1 - Stem Adapter and 1 - Handle Adapter
• Corrosion resistant PVC construction
Stem Extension Kits
Required for Assembly:
• Two-Piece Stem Extension Kit
• Desired Length of PVC Schedule 80 Pipe*
• Saw & Miter Box or Wheel-Type Cutter
• PVC Solvent Cement & Primer
• Black Marker
• Ruler
* NOT INCLUDED
Typical Application
(VALVE AND RISER NOT
INCLUDED)
1: For factory assembled units replace last 3 zeros with length
code. See SSB-1 Part 1 List Price Catalog – Thermoplastic
Valves, Ball Valve Accessories & Repair Kits for length codes.
2: Not for use on True Union 2000 Industrial 3-Way Ball
Valves
2-Piece Stem Extension Kit
Use the Schedule 80 pipe size listed for the appropriate valve size
Valve Size (in.) 1/2 3/4 1 1-1/4 1-1/2 2 2-1/2 3 4 6
Required Sch 80
Pipe Size
3/4 1 1-1/2
To calculate the length of Schedule 80 pipe needed,
subtract the appropriate figure shown below from the desired handle height
For True Union 2000 Industrial Ball Valves
1
Valve Size (in.) 1/2 3/4 1 1-1/4 1-1/2 2 2-1/2 3 4 6
Subtract (in.) 3-7/8 4 4-5/16 5 5-5/8 6-1/4 8-1/16 8-1/16 9-5/8 10-11/16
Minimum Height (in.) 4-9/16 5-3/16 5-1/2 6-3/4 7-3/8 8 9-13/16 9-13/16 11-5/8 12-3/4
For True Union 2000 Standard, Compact 2000 & Single Entry Ball Valves
Valve Size (in.) 1/2 3/4 1 1-1/4 1-1/2 2 2-1/2 3 4 N/A
Subtract (in.) 2-1/2 3-1/16 3-9/16 4-1/4 4-5/8 5-11/16 7-11/16 7-11/16 9 N/A
Minimum Height (in.) 3-5/8 4-1/4 4-3/4 6 6-3/8 7-7/16 9-1/2 9-1/2 11 N/A
For Regular True Union & Compact Ball Valves
Valve Size (in.) 1/2 3/4 1 1-1/4 1-1/2 2 2-1/2 3 4 N/A
Subtract (in.) 3-5/16 4 4-5/16 5-1/8 5-5/8 6-1/16 7-1/8 7-1/8 8-3/8 N/A
Minimum Height (in.) 4-1/2 5-1/4 5-1/2 7 7-1/2 8 9 9 10-1/2 N/A
Valve
Size
Part Numbers
1
For True Union 2000,
Compact 2000 & Single
Entry Ball Valves
2
For Regular True Union &
Compact Ball Valves
1/2 BVSE2-005-000 BVSE-005-000
3/4 BVSE2-007-000 BVSE-007-000
1 BVSE2-010-000 BVSE-010-000
1-1/4 BVSE2-012-000 BVSE-012-000
1-1/2 BVSE2-015-000 BVSE-015-000
2 BVSE2-020-000 BVSE-020-000
2-1/2 & 3 BVSE2-030-000 BVSE-030-000
4 BVSE2-040-000 BVSE-040-000
6 BVSE2-060-000 N/A
1. Cut pipe square to desired
length (See Table Below).
2. Bevel and deburr pipe ends.
3. Align edge of print string
or mark each end of pipe
for alignment; check dry fit.
4. Solvent cement
components to pipe
making sure alignment
marks are properly matched.
5. Push valve handle onto
extension assembly.
6. Position assembly over
valve stem and rotate
into place.
Desired
Pipe
Length.
Desired Handle
Height
(See Table Below)
HANDLE
COMPONENT
STEM
COMPONENT