Installation

ManualsBrandsSpeakman ManualsPlumbingSentinel Pro Collection Wall Mounted Thermostatic Shower Valve Trim, in Polished Chrome

SPEAKMAN

400 Anchor Mill Rd. New Castle, DE 19720 Phone: 800-537-2107 Fax: 800-977-2747

12/07/17 www.speakman.com 92-SM-5000-01

SPEAKMAN

SM-5000

Installation, Operation & Maintenance Instructions

SENTINELPRO™ COMBINATION SERIES

DESCRIPTION

Speakman SentinelPro™ Combination, SM-5000, unites Anti-Scald Thermostatic / Pressure Balance

Shower/Bath Valve with integral Check Stops (CPV-TP) and Trim (CPT-5001).

SPECIFICATIONS

CPV-TP ANTI-SCALD THERMOSTATIC / PRESSURE BALANCE SHOWER VALVE:

CONNECTIONS: ½” Female Copper Sweat and ½” NPT Male at both the Inlets (Cold, Hot) & Outlets

(Shower, Tub)

FLOW RATE: 1.5 gpm (5.7 L/min) or higher

COMPLIANCE: ASSE 1016 / ASME A112.1016 / CSA B125.16 & ASME A112.18.1 / CSA B125.1 Standards

CPT-5001 T/P VALVE TRIM:

FINISH: Polished Chrome

COMPLIANCE: ASME A112.18.1 / CSA B125.1 Standard

INSTRUCTIONS

See individual products for installation of the components and warranty information.

ROUGH-IN

Summary of content (8 pages)

PAGE 1
SPEAKMAN ® SM-5000 Installation, Operation & Maintenance Instructions SENTINELPRO™ COMBINATION SERIES DESCRIPTION Speakman SentinelPro™ Combination, SM-5000, unites Anti-Scald Thermostatic / Pressure Balance Shower/Bath Valve with integral Check Stops (CPV-TP) and Trim (CPT-5001). SPECIFICATIONS CPV-TP ANTI-SCALD THERMOSTATIC / PRESSURE BALANCE SHOWER VALVE: CONNECTIONS: ½” Female Copper Sweat and ½” NPT Male at both the Inlets (Cold, Hot) & Outlets (Shower, Tub) FLOW RATE: 1.5 gpm (5.
PAGE 2
INSTRUCTIONS FOR MODELS TOOLS AND SUPPLIES CPV-TP CPV-TP-DV Pencil Keyhole Saw Adjustable Wrench 1 IMPORTANT • Be sure to read instructions thoroughly before beginning installation. Referencing the supplied rough-in dimensions (located at the end of this manual), determine the preferred location of valve. Align the supplied rough-in template with this location and trace outline of template onto wall.
PAGE 3
6 If your installation is for a shower only, apply thread seal tape to the lower outlet port and install the included cap. Wrench tighten. 7 Ensure Valve is positioned plumb and level. Remove Rough-In Template from Valve. Make threaded connections or plumb and solder all joints and fittings. Take care to protect surrounding area when soldering. Secure piping to surrounding structure. 8 OR Make piping connections for all accessories. Take care to protect surrounding area when soldering.
PAGE 4
CPV-TP / CPV-TP-DV SERVICE INSTRUCTIONS Service instructions Caution- Any repair or servicing of the valve may affect the maximum hot temperature setting of the valve. After working on the valve, make sure the maximum hot water temperature is set to the recommended setting of 110° F maximum. T/P Cartridge Removal 1) Shut off the hot & cold water supply integral stops at the valve. Remove valve trim from valve.
PAGE 5
SPEAKMAN CPV-TP ROUGH-IN DIAGRAM ® A NOTES: COMPLIANCE: ASME A112.18.1/CSA B125.1 1" 25mm HOLE FOR SHOWER ARM Shower Valve ASSE1016 6'-6" [2 METERS] TO FLOOR CONNECTIONS: 1/2" NPT MALE 1/2" SWEAT CONNECTION Hot/Cold Inlets: ½” Female Copper Sweat ½” NPT Male 5-1/2" (140MM) DIA.
PAGE 6
INSTRUCTIONS FOR MODELS CPT-5001 / CPT-5401 TOOLS AND SUPPLIES Phillips Screwdriver Silicone 1 Remove the Handle Button Screw by inserting one of the included Mounting Screws thru the hole in the Handle. Caulk Gun IMPORTANT • Do not over-tighten any connections or damage may occur. • Be sure to read instructions thoroughly before beginning installation. 2 Insert the T/P Rubber Sleeve with Tabs over Valve Bonnet. • This valve has an operating range of 20-80 psi.
PAGE 7
8 Ensure the Rubber Gasket is correctly installed to the Retaining Ring. Align the Retaining Ring with the slots on the Wall Plate. Press and Rotate the ring clock-wise until it Locks / Seals in place. Make sure the seal is secure with the Wall Plate. 10 Insert Handle Button into the Handle. * VIEW FROM BACK UNDERSIDE OF HANDLE If further adjustments need to be made after the Handle Button is inserted, there is an access hole at the back side of the handle. Use a paper clip to push the Button back out.
PAGE 8
SPEAKMAN CPT-5001 ROUGH-IN DIAGRAM ® A 1" 25mm HOLE FOR SHOWER ARM 7.50in 191mm 6'-6" [2 METERS] TO FLOOR 1/2" NPT MALE 1/2" SWEAT CONNECTION 1/2" NPT MALE 1/2" SWEAT CONNECTION 5-1/2" (140MM) DIA. HOLE FOR VALVE ACCESS 4.31in 110mm 1/2" NPT MALE 1/2" SWEAT CONNECTION 3.50in 89mm 3.75in 95mm 1'-9" [533mm] VALVE MOUNTING IS SHOWN FOR REFERENCE ONLY. VALVE IS NOT INCLUDED WITH CPT-5000 4’-6" [1.