Installation

ManualsBrandsSpeakman ManualsPlumbingSensorflo Collection 0.5 GPM Deck Mounted Single Hole AC Powered Bathroom Faucet, in Polished Chrome

92-2840-R2

1of 18

SPEAKMAN COMPANY

S-9100, S-9200, S-9300, S-9400, S-9700, S-9800 Series

Installation, Maintenance & Operation Instructions

SENSORFLO

BATTERY or AC POWERED SLIM DESIGN FAUCETS with DIFFERENT OPTIONS

The Designer Series Faucet is an addition to the existing family of Speakman Sensorflo Products. Its unique

features such as operating mechanisms ( Solenoid and Power pack) ready serviceable from under the counter, integral

Hot and Cold mechanical mixing valves, Hot and Cold water supply check valves, standard inline filters, and a new

Sensor Module design incorporated into solid brass Faucet body make it ideal for public areas such as schools, hotels,

laboratories, and hospitals.

Speakman SENSORFLO

Slim Design Faucets, Batteries or AC/DC powered comes in different Faucet Spout

shapes as: Gooseneck, Modern Tubular or Cast C-Spout, all with a Sensor Module installed inside.

Inside the solid brass body of the Faucet sits only the Infrared Sensor Module. The Solenoid and the Power

Supply (Batteries or AC/DC adapter) are located under the sink with easy accessibility.

The Sensor module is powered by two (2) 3-volt DC lithium batteries or AC/DC adaptor with waterproof

connectors housed in a separate Power Module attached under counter mounted onto the Solenoid body. There is a low

battery warning light that pulsate before the batteries are depleted and keeps pulsating at least for 2 weeks after they are

no longer in service.

Speakman SENSORFLO faucets are thoughtfully designed and engineered in accordance with the highest

quality and performance standards. Require no handles to turn, lift or push water flows. Built in vandal resistant

circuitry shuts off the water after continuous flow of approximately 60 seconds. This feature prevents flooding:

-water is easily turned on again by placing one’s hands under the lavatory spout.

Water conserving vandal resistant recessed aerator reduces water flow to 2.2 GPM / 8.4 LPM to meet

requirements of ANSI A112.18.1M for flow rates. There is a water Filter on the Solenoid ready accessible for

maintenance purposes. ADA (American Disabilities Act) compliant. NOTE: Stainless steel hoses are optional.

SPECIFICATIONS

INLET SUPPLY: 3/8” COMPRESSION WITH MALE THREADS for Cold and Hot Water

FLOW RATE: 2.2 GPM / 8.4 LPM

FINISH: BRASS CHROME PLATED

OPTIONS

BO – Boca VR 0.5 GPM Flow Control HS – 2SS Hoses for use with UCM, 3/8”compression

LF – Laminar Flow 2.2 GPM Flow Control HTS – 1SS Hose for Tempered water, 3/8”compression

TMV – UC Thermostatic Valve with check valves –T – Tee with checks

GB – Vandal resistant 1.5 GPM Aerator Outlet device

All Faucets come in different combinations with:

NO Deck Plate

4” Deck Plate

8” Deck Plate

UCM (under counter mixing valve with built-in backflow check valves)

TMV (thermostatic mixing valve for more consistent water temperature with check valves)

ACM (above counter mixer)

MO (manual override)

Three different shapes of Faucets, all made of solid polished chrome brass can be mounted onto a unique Central

Base with the Infrared Sensor Module. The Solenoid is attached to the central shank and has installed on it the Power

Module that can be either with batteries or AC adapter that plugs into a Transformer.

Summary of content (18 pages)

PAGE 1
of 18 SPEAKMAN COMPANY S-9100, S-9200, S-9300, S-9400, S-9700, S-9800 Series Installation, Maintenance & Operation Instructions SENSORFLO® BATTERY or AC POWERED SLIM DESIGN FAUCETS with DIFFERENT OPTIONS The Designer Series Faucet is an addition to the existing family of Speakman Sensorflo Products.
PAGE 2
of 18 Different combinations could be made between UCM (or TMV), ACM and MO mounted directly onto Counter Top or onto 4” or 8” Deck Plates.
PAGE 3
of 18 INSTALLATION OF AERATOR To install vandal resistant aerator screw the aerator into the outlet of the faucet with the provided Speakman aerator wrench INSTALLATION OF POWER MODULE TO SOLENOID If the Power Module (either battery or AC) is not installed onto Solenoid body, attached it as shown with 2 provided screws #8. INSTALLATION OF FAUCET Insert the faucet shank into a 1-1/8” hole with connector wires going in first, taking care not to pinch the wires.
PAGE 4
of 18 Under sink, place rubber wire guard (with notch facing forward) and pass the wires through notch. The wires should be inside channel of rubber wire guard to prevent pinching when tightening. Insert metal washer and tighten the locknut to provide enough tension into the rubber guard. While tightening make sure the position of Faucet on top of counter is straight. Again make sure that the wires are not pinched.
PAGE 5
of 18 Install 3/8”compression fitting hoses to the UCM (under counter mixing valve). The hot and cold sides are marked H and C. Hand tighten connections and then slightly tighten with an adjustable wrench. DRY CONNECTION ONLY. NOTE: During winter month it may be necessary to reverse Hot and Cold connections to obtain warmer temperature range of water. After connecting to supply lines, turn on the water and activate the faucet with your hands, checking for leaks.
PAGE 6
of 18 Remove the 2 screws on the clamp. After removing, pull up the Sensor Module from the central shank (do not damage the O-Rings and the wire connectors). Reassemble new Module with care not to cut wires through the big holes into the Base, then insert the clamp with the Sensor over the shank. Tighten the 2 screws on clamp, making sure that the sensor sits on the flat of shank and touches the bottom of base. Grease the 2 O-Rings or change them if they are damaged.
PAGE 7
of 18 92-2840-R2
PAGE 8
of 18 92-2840-R2
PAGE 9
of 18 3 BASIC MODELS: Three different shapes of Faucets, all made of solid polished chrome brass could be mounted onto a unique Central Base with the Infrared Sensor Module in it. The Solenoid is attached to the central shank and has installed on it the Power Module that can be either with batteries or AC adapter that plugs into a Transformer.
PAGE 10
of 18 OPTIONS: ACM (above counter mixer) Installation 1. With the Flange Nut, steel washer and rubber washer on the shank, install ACM from the bottom. 2. Tighten the top Flange Nut adjusting the proper height above counter. 3. Tighten then the bottom Flange Nut until the assembly is fixed in place. 4. Insert the Handle and tighten with the screw onto the shank. 5. Snap the screw cover onto Handle. 6. Attach the Hot and Cold hoses from supply line to ACM (see marks on body) 7.
PAGE 11
of 18 MO (manual override) Installation (Also see page 14) 1. First insert the Thin Nut on the Faucet shank a little higher. 2. Insert Mount bracket and tighten the Solenoid Nut. (dry connection only) 3. Lower the Thin Nut onto bracket 4. Slip compression spring onto MO spindle 5. With O-Ring attached to the Spacer, slip Spacer and Bearing Sleeve onto spindle 6. With the lock washer and screw inside the Handle, properly position Handle onto Spindle. 7.
PAGE 12
of 18 UCM (under counter mixer) with MO (manual override) Installation 1. Install the MO as described above. 2. Install the UCM fixed on the wall with the Clamp in the desired position. 3. The UCM it is marked with H and C for hot and cold supply lines. The mixed water exits on top into the Tee. 4. The water supply splits into the Tee: -one exit hose goes to Solenoid and the other hose goes to bottom of MO. 5.
PAGE 13
of 18 ACM (above counter mixer) with MO (manual override) Installation 1. Install the MO and ACM as described above. NOTE: In this case the ACM has an extra By-pass outlet: -in total 2 branches of mixed water. 2. There are two branches with mixed water: -one goes to Solenoid inlet, and the other goes to bottom of MO. 3. Form the side of MO the by-pass hose goes to the upper side of Solenoid discharge for manually controlled side NOTE: For MO is used a Solenoid with a by-pass branch at its outlet.
PAGE 14
of 18 MO (Manual Override ) ASSEMBLY INSTALLATION INSTRUCTIONS FOR SLIM DESIGN FAUCETS 92-2840-R2
PAGE 15
of 18 MO (Manual Override ) HOSE INSTALLATION INSTRUCTIONS For ease of installation attach hoses to ACM (above counter mixer) and MO (manual override) diverter before installing under the sink. 1. Attach hot supply hose 1 to inlet ports of mixer (H port) 1 either ACM or UCM. 2. Attach cold supply hose 2 to inlet ports of mixer (C port) 2 either ACM or UCM. 3. Connect one end of diverter supply hose 3 to the Elbow outlet 3 on ACM or TEE outlet 3 on UCM.
PAGE 16
of 18 Repair Parts List Part/Group Number RPG05-0674-PC RPG38-0128-PC RPG05-0792-PC RPG76-0033-LBL RPG 76-0039 RPG 66-0044 RPG66-0168 RPG66-0169 RPG76-0041 RPG66-0169-AC RPG66-0010 RPG20-1845 RPG66-0111 RPG05-0836 66-0163 Description Refer to Instructions 13/16 -2.2 GPM Aerator repair group 13/16 -0.
PAGE 17
of 18 TROUBLESHOOTING Before calling Speakman Company for service, please run through the following checklist of troubleshooting steps. It may be necessary to turn off the hot and cold water supply stops before proceeding to work on the Sensor Faucet. Faucet Operation If water flow from the faucet decreases 1. Make sure the supply stops are open. 2.
PAGE 18
of 18 QUESTIONS & ANSWERS Q. How does the Sensorflo® faucet work? A. It uses infrared technology. The sensor emits a non-visible beam of light. When an object enters the detection area, the sensor signals the solenoid valve to open for water to flow. When an object leaves the detection area, the sensor signals the valve to close. Q. Is the Speakman Sensorflo® faucet sensor beam adjustable? A. No, the Speakman Sensorflo® faucet sensor beam is not adjustable.