Installation Guide

ManualsBrandsSpeakman ManualsBathSentinelPro 1-Handle 1-Spray Shower Faucet Trim Kit in Polished Chome (Valve Included)

PAGE 1 09/10

92-3141

SPEAKMAN COMPANY

Sentinel Pro Thermostatic/Pressure Balancing Valve, Showerhead, Tub

Spout, & Combo Series Installation, Operation, & Maintenance Instructions

DESCRIPTION

Speakman Sentinel Pro concealed anti-scald thermostatic/pressure balancing shower /bath valve & combinations.

Chrome plated brass wall plate. Chrome plated metal lever handle. Adjustable temperature limit stop ((TLS) Factory

set @ 110 F°). Brass body with integral spring check stops. Thermostatic element/piston type pressure balancing

cartridge assembly. Can be installed back to back. Roughing-in template. S-2272-E2 showerhead (If applicable), S-

2280 Anystream wall mounted showerhead (If applicable), or VS-100 Handheld Shower (If applicable) with flow

control device reduces flow to 2.5 GPM/9.46 LPM maximum to meet existing ASME A112.18.1/CSA B125.1

Standard. Chrome plate brass shower arm and wall flange (If applicable). Chrome plated tub spout (If applicable). Four

port valve with ½” female copper sweat inlets and shower outlet. ½” NPT female tub outlet. Meets ASME

A112.18.1/CSA B125.1 & ASSE 1016 standards.

SPECIFICATIONS

SUPPLY: ½” FEMALE COPPER SWEAT INLETS & SHOWER OUTLET; ½” NPT FEMALE TUB OUTLET

(VALVE)

FLOW RATE: 2.5 GPM/9.46 LPM MAX. (SHOWERHEAD AND/OR HANDHELD SHOWER, IF APPLICABLE)

SHIPPING WEIGHT: 5 LBS (SM-5000)

OPTIONS

INSTALLATION INSTRUCTIONS

Important-

Read these instructions before installing the valve. Use the correct “Rough-in Diagram” for the unit that is

being installed. Maximum water pressure: 125 PSI static; minimum water pressure: 20 PSI flowing; minimum cold

supply temperature: 40° F; maximum hot supply temperature: 160° F; minimum hot supply temperature: 5° F above set

point. Use a suitable sealant on all threaded connections and when soldering, it is recommended to remove the integral

check stop valve parts and VC/DIV cartridge (If applicable). The valve rough-in adjustments are 2-1/2” to 3-1/2” from

the finished wall to the centerline of the hot & cold inlets of the valve body.

1) Referring to the correct “Rough-in Diagram” for the unit

that is being installed (See the back page or the separate

insert sheet), install the hot & cold supply lines for the

valve, making sure they are on an accurate horizontal

plane. Taking the valve assembly, making sure the “UP”

on the valve bonnet is in the up position, connect the hot

supply line to the left side of the valve & the cold supply

line to the right side of the valve (Note that for Back- To-

Back valve installations, the hot & cold supply lines are

reversed on the opposite valve). Make sure the valve is

straight, level, & positioned properly in the wall (See

Figure 1). See Page 3, Figure #4 for “Back-To-Back”

valve cartridge installation instructions.

 1 -

S-2251 Showerhead  6 - S-2288 Showerhead  AP - Anchor Plate (S-2280

Showerhead Only)

 2 - S-2252 Showerhead  9 - S-2292 Showerhead  BJ - Ball Joint (S-2280

Showerhead Only)

 2VR - S-2252 Vandal Resistant

Showerhead

 PC –

Polish Chrome Handheld

Shower (Combo w/VS-100 Only)

 VH- White Vinyl Hose (Combo

w/Handheld Shower Only)

 3 - S-2253 Showerhead  LH - Less Showerhead 

Summary of content (5 pages)

PAGE 1
SPEAKMAN COMPANY Sentinel Pro Thermostatic/Pressure Balancing Valve, Showerhead, Tub Spout, & Combo Series Installation, Operation, & Maintenance Instructions DESCRIPTION Speakman Sentinel Pro concealed anti-scald thermostatic/pressure balancing shower /bath valve & combinations. Chrome plated brass wall plate. Chrome plated metal lever handle. Adjustable temperature limit stop ((TLS) Factory set @ 110 F°). Brass body with integral spring check stops.
PAGE 2
) Slip the rough-in template over the valve control spindle. If the opening in the wall is smaller than the outside diameter of the template, trace the outside diameter of the template, remove the template, and recut the opening in the wall. Slip the template onto the valve again until the template bottoms out on the top of the valve bonnet (See Figure 2).
PAGE 3
plate and index cut outs. With your fingers, firmly push and rotate the ring clockwise to lock into place. Properly position the handle onto the valve spindle and screw into place. Push index button into the handle. BACK-TO-BACK INSTALLATION On this type of installation, the thermostatic/pressure balancing cartridge must be rotated 180° on the valve on which the hot & cold inlets are reversed. Refer to Figure #4 on this page for the proper positioning of the cartridge.
PAGE 4
MAINTENANCE (CARE and CLEANING) The Speakman Sentinel Pro thermostatic/pressure balancing shower /bath valve should provide years of reliable service. This type of valve must be cleaned and maintained on a regular basis. Periodic maintenance should be performed at least every 12 months or after any changes have been made to the building’s plumbing system. This maintenance should include removing and cleaning the spring check stop components. Make sure the stop poppet in each stop moves freely.
PAGE 5
REPAIR / REPLACEMENT PARTS ITEM NUMBER PART OR GROUP NUMBER 1 2 3 4 5 6 RPG49-0126 RPG05-0718 RPG05-0860 RPG49-0006 RPG05-0847 RPG05-0862 PAGE 5 DESCRIPTION BONNET O-RING BONNET, SCREWS (4), & O-RING REPAIR GROUP T/P REPAIR CARTRIDGE (COMPLETE w/SPINDLE) LOWER QUAD RINGS (2) FOR T/P CARTRIDGE VOLUME CONTROL/DIVERTER CERAMIC REPAIR CARTRIDGE CHECK STOP REPAIR GROUP (REPAIRS BOTH STOPS) 09/10 92-3141