Installation & Assembly

ManualsBrandsSpeakman ManualsBathroom Remodel & Bathroom FixturesLow Arc Sensor Centerset Bathroom Faucet

INSTRUCTIONS FOR MODELS

92-SFC-8790-01

For additional assistance or service please contact:

SPEAKMAN

800-537-2107

customerservice@speakman.com

www.speakman.com

SFC-8790

TOOLS AND SUPPLIES

Adjustable

Wrench

Extended Phillips

Screwdriver

PencilDrillScissors

Aerator

Wrench

(included)

Tor x Bit

(Included)

Bit

Driver

HELPFUL TOOLS & SUPPLIES:

Safety

Glasses

Liquid

Soap

Foam

Soap

Warranty information can be found at:

www.speakman.com

WARRANTY

MAINTENANCE

Cover your drain to prevent loss of parts. Be sure to

wear eye protection while cutting pipe.

SAFETY TIPS

IMPORTANT

• Be sure to read instructions thoroughly before

beginning installation.

• Do not over-tighten any connections or damage

may occur.

• This faucet has an operating range of 20-80 psi.

Your new Speakman Product is designed for years of

trouble-free performance. Keep it looking new by

cleaning it periodically with a soft cloth. The use of harsh

chemicals and abrasives may damage the finish and

void the product warranty. Please be sure to only use

approved cleaners. Please contact Speakman for any

clarification of acceptable cleaners.

Place the Deck Plate (1) on top of the desired

mounting surface. Ensure the two (X2) mounting

holes are aligned.

Remove Mounting Hardware (1) from faucet.

Verify that the Rubber Gasket (2) is in position

and aligned to the base of the faucet.

NOTE: If an AC Adaptor is being used, locate

the AC Connector Cable (Green) (3) inside the

faucet body and pull the connector out.

Place Hose and Sensor Wire carefully, one at a

time, thru hole in mounting surface. Lower Faucet

into position.

FAUCET INSTALLATION

From below, install Rubber Washer (1), Metal

Washer (2), and secure with Mounting Nuts (3).

Align Faucet to desired position and wrench

tighten Mounting Nuts (3).

Ensure the water supplies are turned off.

This faucet uses a Single Hose Mixed inlet.

Attach the Hose of the Faucet to a water supply.

Wrench Tighten.

WATER

SUPPLY

If Tepid Water is desired, a Speakman A-TMV

Thermostatic Mixing Valve is recommended.

FAUCET INSTALLATION

Remove the Rubber Washer (1), Metal Washer

(2) and Mounting Nuts (3) from the Mounting

Studs.

Place all Hoses, Sensor Wire and Mounting

Studs through the mounting hole one at a time.

Take extra precautions to avoid pinching any

wires or hoses. Lower Sensor Soap Dispenser

into position.

SOAP DISPENSER INSTALLATION

From beneath, reinstall the Rubber Washer (1),

Metal Washer (2) and Mounting Nuts (3) to

secure the Sensor Soap Dispenser. Align the

Sensor Soap Dispenser to desired position and

wrench tighten Mounting Nuts (3). Verify that the

wires and hoses are not pinched.

Place the Control Box (1) against the desired mounting surface while ensuring adequate

clearance for servicing of all connections. If using the A/C Adapter, consider the distance to

the nearest electrical outlet. Control Box should be mounted so the Soap and Air Outlet Ports

are facing up.

14" MA

IN A

LL DIRECTIONS

A/C ADAPTER

Mark Screw Hole mounting locations (X4) using a Mounting Screw

(included) and an extended Phillips Screw Driver. Mount the Control

Box onto the previously marked locations. If mounting on drywall and

not to stud, use the appropriate anchors and fasteners for

application. Recommend screw in EZ anchor or equal for drywall.

SOAP DISPENSER INSTALLATION

Summary of content (6 pages)

PAGE 1
INSTRUCTIONS FOR MODELS IMPORTANT TOOLS AND SUPPLIES Bit Driver Extended Phillips Screwdriver SFC-8790 Adjustable Wrench • Do not over-tighten any connections or damage may occur. Aerator Wrench (included) • Be sure to read instructions thoroughly before beginning installation. • This faucet has an operating range of 20-80 psi. Scissors Drill Torx Bit (Included) SAFETY TIPS Pencil Cover your drain to prevent loss of parts. Be sure to wear eye protection while cutting pipe.
PAGE 2
SOAP DISPENSER INSTALLATION 11 Align the SOAP and AIR tubes to the Control Box. Cut to length and press tubing over barbed fittings on Control Box. FILL/REFILLING SOAP 12 Open the Soap Bottle Lid by pulling the C Clip away. 13 Lift the Cap to access soap bottle. 14 Pour Soap into the Soap Container. This Soap Dispenser will work with both Liquid Hand Soap and Foaming Hand Soap with a viscosity of < 1000cP.
PAGE 3
22 22 24 SENSOR FAUCET BATTERY POWER FAUCET BATTERY 23 POWER SENSOR FAUCET BATTERY POWER Install the Battery Box Cover (1) and reconnect the GREEN Connector (2). Make sure the cover is fully pressed in. FAUCET BATTERY POWER 23 Insert the Battery Box (1) into the Faucet Body and install the Faucet Lid (2). 25 Fasten the 2 Vandal Resistant Screws (1). Make sure there are no gaps between the Lid and the Faucet Body.
PAGE 4
SFC-8790 CARE AND CLEANING 1) Your SENSORFLO® Faucet is designed and engineered in accordance with the highest quality and performance standards. With proper care, it will provide years of hygienic and trouble-free service. 2) Periodically, the Faucet will require some minor maintenance to keep it at peak performance. There is a low battery indicator located on the Sensor on the Faucet body. When the low battery light on the Sensor blinks, it indicates that the battery is low.
PAGE 5
SPEAKMAN ® SFC-8790 BELOW COUNTER ROUGH-IN DIAGRAM LAVATORY ROUGH-IN 2" 51mm MIN. TO WALL 1 1 " MIN 4 32mm 1 1 " MIN 4 32mm 2" 51mm MIN. TO LEDGE 2" MAX DECK THICKNESS 14" MAX IN ALL DIRECTIONS 36" WIRE 36" 12" MIXED WATER INLET 9/16"-24 UNEF ALL DIMENSIONS ARE IN INCHES (MILLIMETERS) UNLESS OTHERWISE SPECIFIED. DIMENSIONS SUBJECT TO CHANGE WITHOUT NOTICE. SFC-8790 ROUGH-IN DIAGRAM NOTES: COMPLIANCE: ASME A112.18.1/CSA B 125.1 FLOW DATA: • 0.5gpm (1.
PAGE 6
SFC-8790 REPAIR PARTS ITEM NO. PART NO. DESCRIPTION RPG05-108059 0.