Specification Sheet

SPEAKMAN
400 ANCHOR MILL ROAD
NEW CASTLE, DE 19720
800-537-2107
800-977-2747
WWW.SPEAKMAN.COM
JU LY 2017
Architect/Engineer Approval Space:
P:
F:
W:
R:
524
4”
( 102mm )
6” MIN ( 152mm )
12” MAX ( 305mm )
4⅜”
( 111mm )
MOUNT
VALVE
18 MAX.
BELOW
COUNTER
2” MAX
( 51mm )
Ø 2¼”
( 57mm )
Ø 1⅛”
( 28mm )
HOT ENDBODY
SUPPLY INLET
½” NPSM MALE
*NOTE- MOUNT THE
MIXING VALVE USING
1/2 PIPE HANGERS (2)
WITH WALL PLATES (2).
(NOT INCLUDED)
COLD ENDBODY
SUPPLY INLET
½” NPSM MALE
COLD WATER
SUPPLY INLET
BEFORE MOUNTING
VERIFY THE SUPPLY
HOSES WILL REACH
THE CONNECTIONS
HOT WATER
SUPPLY INLET
THERMOSTATIC
MIXING VALVE
OUTPUT
TEPID SUPPLY
INLET FOR
EYEWASH
½” NPT MALE
COUNTERTOP
MAX HEIGHT 36” ( 914 mm )
MIN HEIGHT 24” ( 610 mm )
Ø 1¾”
( 44mm )
15/16”
( 24 mm)
5½”
( 140mm )
*
8”
( 203mm )
4”
( 101mm )
*
6”
( 158mm )
6” MIN ( 152mm )
FROM ANY
OBSTRUCTION
EYEWASH
HOSE
COLD HOSE
HOT HOSE
* = -8 Dimensions
NOTE: All dimensions are in inches (millimeters)
unless otherwise specified and are subject to change.
9” ( 229mm )
*
11” ( 279mm )
5” ( 133mm )
*
7” ( 184mm )
DIMENSIONS:
NOTE: 1. Side mounting (right or left) of the mixing valve is recommended. Mounting valve below the sink tting may damage the mixing
valve’s temperature gage during use of the sink tting. 2. Sink tting inlets are 1/2-14 NPT female. 3. All dimensions are in inches (millimeters)
unless otherwise specied and are subject to change without notice.
SEF-1800-CA Spray Plume Length and Flow
Flowing Pressure
30 psi 40 psi 50 psi 60 psi 70 psi 80 psi
2.07 Bar 2.76 Bar 3.45 Bar 4.14 Bar 4.83 Bar 5.52 Bar
Flow Rate
2.9 gpm 3.1 gpm 2.9 gpm 2.9 gpm 2.9 gpm 2.9 gpm
11.09 L/min 11.55 L/min 11.13 L/min 10.98 L/min 10.90 L/min 10.86 L/min
Eyewash Distance
Plume ”A”
13.5” 14.25” 14.25” 13.75” 13.75” 13.75”
34.29 cm 36.2 cm 36.2 cm 34.93 cm 34.93 cm 34.93 cm
SEF-1800-CA-8 Spray Plume Length and Flow
Flowing Pressure
30 psi 40 psi 50 psi 60 psi 70 psi 80 psi
2.07 Bar 2.76 Bar 3.45 Bar 4.14 Bar 4.83 Bar 5.52 Bar
Flow Rate
2.9 gpm 3.1 gpm 2.9 gpm 2.9 gpm 2.9 gpm 2.9 gpm
11.09 L/min 11.55 L/min 11.13 L/min 10.98 L/min 10.90 L/min 10.86 L/min
Eyewash Distance
Plume “A”
17.0” 18” 17.5” 17.0” 17.0” 17.0”
43.18 cm 45.72 cm 44.45 cm 43.18 cm 43.18 cm 43.18 cm
4”
( 102mm )
6” MIN ( 152mm )
12” MAX ( 305mm )
4⅜”
( 111mm )
2” MAX
( 51mm )
Ø 2¼”
( 57mm )
Ø 1⅛”
( 28mm )
HOT
SUPPLY INLET
½” NPSM MALE
COLD
SUPPLY INLET
½” NPSM MALE
COLD
SUPPLY INLET
FOR EYEWASH
½” NPT MALE
COUNTERTOP
MAX HEIGHT 36” ( 914 mm )
MIN HEIGHT 24” ( 610 mm )
* = -8 Dimensions
NOTE: All dimensions are in inches (millimeters)
unless otherwise specified and are subject to change.
6” MIN ( 152mm )
FROM ANY
OBSTRUCTION
4”
( 101mm )
*
6”
( 158mm )
5½”
( 140mm )
*
8”
( 203mm )
5” ( 133mm )
*
7” ( 184mm )
9” ( 229mm )
*
11” ( 279mm )
Ø 1¾”
( 44mm )
15/16”
( 24 mm)
LAVATORY ROUGH-IN
6” MIN - 12” MAX
Ø 1⅜”
( 35mm )
TYP.
Ø 1”
( 25mm )
2”
( 51mm )
MIN. TO WALL
2”
( 51mm )
MIN. TO LEDGE
4”
( 102mm )
6” MIN ( 152mm )
12” MAX ( 305mm )
4⅜”
( 111mm )
2” MAX
( 51mm )
Ø 2¼”
( 57mm )
Ø 1⅛”
( 28mm )
HOT
SUPPLY INLET
½” NPSM MALE
COLD
SUPPLY INLET
½” NPSM MALE
COLD
SUPPLY INLET
FOR EYEWASH
½” NPT MALE
COUNTERTOP
MAX HEIGHT 36” ( 914 mm )
MIN HEIGHT 24” ( 610 mm )
* = -8 Dimensions
NOTE: All dimensions are in inches (millimeters)
unless otherwise specified and are subject to change.
6” MIN ( 152mm )
FROM ANY
OBSTRUCTION
4”
( 101mm )
*
6”
( 158mm )
5½”
( 140mm )
*
8”
( 203mm )
5” ( 133mm )
*
7” ( 184mm )
9” ( 229mm )
*
11” ( 279mm )
Ø 1¾”
( 44mm )
15/16”
( 24 mm)
LAVATORY ROUGH-IN
6” MIN - 12” MAX
Ø 1⅜”
( 35mm )
TYP.
Ø 1”
( 25mm )
2”
( 51mm )
MIN. TO WALL
2”
( 51mm )
MIN. TO LEDGE