Installation & Assembly

ManualsBrandsSpeakman ManualsBathroom Remodel & Bathroom FixturesLura Widespread Bathroom Faucet with Drain Assembly

INSTRUCTIONS FOR MODELS

92-CD5XX-03

For additional assistance or service please contact:

SPEAKMAN

800-537-2107

customerservice@speakman.com

www.speakman.com

CD521

CD522

CD523

HELPFUL TOOLS & SUPPLIES:

TOOLS AND SUPPLIES

Adjustable

Wrench

Slip Joint

Wrench

Thread Seal

Tape

Aerator

Wrench

(included)

Phillips

Screwdriver

Safety

Glasses

Plumber’s

Putty

Hex Key

Wrench

(included)

Level

Warranty information can be found at:

www.speakman.com

WARRANTY

Your new Speakman Product is designed for years of

trouble-free performance. Keep it looking new by

cleaning it periodically with a soft cloth. The use of harsh

chemicals and abrasives on any of the Speakman custom

finish products may damage the finish and void the

product warranty. Please be sure to only use approved

cleaners. Please contact Speakman for any clarification

of acceptable cleaners.

MAINTENANCE

Cover your drain to prevent loss of parts. Be sure to

wear eye protection while cutting pipe.

SAFETY TIPS

IMPORTANT

• Be sure to read instructions thoroughly before

beginning installation.

• Do not over-tighten any connections or damage

may occur.

• This faucet has an operating range of 20-80 psi.

Remove Inlet Hose Assembly (1), Mounting

Nut (2), Metal Washer (3), and Rubber

Washer (4) from Spout.

Remove Mounting Nut (1), Metal Washer

(2), and Rubber Washer (3) from Cold

Endbody Assembly. Repeat process for Hot

Endbody Assembly

The “COLD” and “HOT” Endbody Assemblies are clearly marked. Place COLD Endbody

Assembly through the appropriate hole in the counter top. Align Endbody Assembly so the

Rubber Access Plug (1) is facing the rear. Repeat process for the HOT Endbody Assembly.

From below, reinstall the Endbody Rubber Washer (1), Metal Washer (2), and Mounting

Nut (3). Loosely assemble at this time. Repeat process for the HOT Endbody Assembly.

Place Spout Assembly through the center hole of counter top. From below, reinstall the Spout

Rubber Washer (1), Metal Washer (2), and Mounting Nut (3). Loosely assemble at this time.

Reinstall Inlet Hose Assembly (4)

NOTE:

Opening within the Metal

Washer (2) should face

towards the rear.

Summary of content (6 pages)

PAGE 1
INSTRUCTIONS FOR MODELS CD521 TOOLS AND SUPPLIES Adjustable Wrench Aerator Wrench (included) Slip Joint Wrench Hex Key Wrench (included) 1 Remove Inlet Hose Assembly (1), Mounting Nut (2), Metal Washer (3), and Rubber Washer (4) from Spout. 5 Place Spout Assembly through the center hole of counter top. From below, reinstall the Spout Rubber Washer (1), Metal Washer (2), and Mounting Nut (3). Loosely assemble at this time.
PAGE 2
6 From above, align Spout and Handle bases so that they are aligned horizontally. 7 While maintaining the proper alignment, Wrench Tighten Spout Mounting Nut (1). Then snug Endbody Mounting Nuts (2). Final tightening of Endbody mounting is accomplished by Tightening the Mounting Screws (3) while using a Phillips Screwdriver. Wrench tighten Spout Inlet Hose (4). 8 9 From below, install the Endbody Outlet Hoses (1) (shorter hose) to the Inlet Tee of the Spout (2). Wrench Tighten.
PAGE 3
11 Remove Stopper ❶, Flange Nut ❷, and Flange Washer ❸ from Drain Assembly. 12 From beneath, insert Drain Assembly through drain hole in sink. Attach supplied Flange Washer ❶ or plumber’s putty to the underside of the Flange ❷. Secure Flange ❷ to the Drain Assembly. Align the Drain Assembly as shown below. 13 From beneath, secure Rubber Washer ❶, Plastic Washer ❷, and Mounting Nut ❸. Wrench tighten. 14 Remove Pivot Nut ❶, from Drain Assembly. Install Outer Pivot Washer ❷, and Pivot Rod ❸.
PAGE 4
SPEAKMAN CD5XX REPAIR PARTS ® X2 ITEM NO. PART NO.
PAGE 5
SPEAKMAN CD521 ROUGH-IN DIAGRAM ® NOTES: +4" 10 3 " - 2" 4 +102 273mm - 51 COMPLIANCE: 4" 8"+2" +102 203mm - 51 ASME A112.18.1/CSA B 125.1 AB1953 NSF 372 NSF 61 FLOW: 5 7 " 16 138mm Flow Rate: 1.2 gpm Flow Type: Aerated 1 3 " 16 30mm 3" 8 9mm CONNECTIONS: For flexible hose connection Hot Supply- 9/16-24UNEF-2B Cold Supply- 9/16-24UNEF-2B 75" 8 193mm Contractor to supply necessary connections to the inlets of the end bodies.
PAGE 6
SPEAKMAN CD523 ROUGH-IN DIAGRAM ® 4" 14"+2" +102 356mm - 51 NOTES: COMPLIANCE: 4" 8"+2" +102 203mm - 51 ASME A112.18.1/CSA B 125.1 AB1953 NSF 372 NSF 61 FLOW: 5 7 " 16 138mm Flow Rate: 1.2 gpm Flow Type: Aerated 1 3 " 16 30mm 3" 8 9mm CONNECTIONS: For flexible hose connection Hot Supply- 9/16-24UNEF-2B Cold Supply- 9/16-24UNEF-2B 75" 8 193mm 4 15 " 16 126mm Contractor to supply necessary connections to the inlets of the end bodies. LAVATORY ROUGH-IN 6” MIN - 12” MAX 2" 51mm MIN.