I Preface This gaming desk consists of a heavy-duty steel desk frame and a desktop. Please read and completely understand this manual before installation in order to make sure the safe and correct use of the system and maintain the longevity of the overall construction. Instructions of Safety and Warnings: = Any failure to comply with the safety and installation instructions in this manual may cause serious bodily injury.
I Preparation 0 ‘What are the specifications you need to know? Weight Capacity Operation Temperature 50kg (Toils) [2] ‘What are the tools you require while installation? = & ® Bubble Level Allen Wrench Drill Phillips Screwdriver (Included) oO ‘What's the thing you'd better have before Installation? A Shipping Blanket to protect the desk and the floor 0 Things you need to know before installation Please check all of the components shown in the component checklist, If any of the components are missing or dama
I Installing the Desktop (Jae + Please prepare a spacious area for installation, and put a shipping blanket on the area to prevent scratches on the floor and the desktop. §-A (x4) $B (x2) 5-C (xB) $-D (x4) SE O05) « Place the desktop ©) upside down and assemble the desktop with 2 connection bars (3 M5x14 Mex M6x30 M6x50 ST35x13 as shown using 12 screws CID) .
1 Assembling the Cable Management Tray » Align the holes found on the hooks members to the holes found on the connection bars, » Attach the cable management tray to the connection bar as shown with the hand screws released previously. « Release the hand screw on the hook () as shown and save it + Insert another 2 screws C3) from below as shown to for further use. attach the hook @) to the cable management try (B + Insert a Phillips screw EI) to the hole found on the bottom Tighten all screws.
1 Attaching the Crossbar + Attach the Crossbar Oto the Lifting Columns G/@ using 4 M6x50 Screws (J) and 2 M6x25 Screws (32) as shown in the illustration. + Loosen the hex head screws that fix the | adjustable Junction, but don't completely | take out the screws.
1 Attaching the Anti-Vibration Pads and AC Adapter * Hang the Adapter Holder (Jon the crossbar as shown, then put the AC Adapter) into it. + Attach the Anti-Vibration ras) to the surface of the crossbar on the ten positions as shown. n 1 Attaching the Feet + Place the Lifting Column (3 / (FQ upside down on the orifice . + Attaching the Foot {to the Lifting Column using 4 Mex Screws (ID). * Repeat the same process to attach the other foot.
1 Adjusting the Frame 1 Attaching the Sync Rod * Carefully place the desktop upside down on the blanket/floor. « Place the legs one on each side of the top as shown below. + Adjust the crossbar to the size of the desktop. Ensure that the frame is placed in the center of the desktop. + Tighten the screws on the crossbar. + Turn the knob as shown to loosen and adjust the Sync Rod * Insert both ends of Sync Red into holes found on the desk frame as shown in the illustration. * Re-tighten the knob.
1 Drilling to the Desktop 1 Connecting Cords and Attaching the AC Adapter + Attaching the assembled desk frame to the desktop through the mounting holes + Connect the Controller with the AC Adapter @) and motor as shown. found on the Side Brackets and Crossbar as shown in the illustration using « Insert the Power Plug {J# into the AC Adapter. 10 M5x14 Screws (OD Note: = Do not plug into the power before the desk is fully assembled.
ies 1 Attaching the Accessory the Controller and Cable Management 1 Attaching oO, and in the illustration. + Attach the Drink Holder (5), Headphone Caddie two Light Covers (3) as shown Ips to the desktop with ST3.5x13 Screws to ensure clean and neat surface. + Attach the Controller to the desktop using 2 ST3.
I Attaching the RGB Light Strip I Laying the Surface Pad + Attach the cable clips 0 to the desk, then channel the RGB Light Scrip } through light covers as shown.
1 Adjusting the Desk © Tum over the species with the help of another person. + Thea ara two adjustable foot pads under each foot. If the floor isn't vane, simply tum the pad to adjust the level to make the desk stable. Ti: Use a bubble level (pot included) to check i the desktop is even. CAUTION: At fast two people are required when muting over the dies; or serious bally injures might occur.
