Owner's manual
FI
X
TURE
ARM
FLAT
W
AS
HER
1/2" HE
X
BOL
T
LO
CKW
AS
HER
AF
TE
R
LEV
ELI
N
G
FIXTUR
E T
H
AT
IS ATTA
CHED
TO
M
AS
T A
RM
PIPE,
U
SE
H
OL
E I
N M
AS
T A
RM F
ITTE
R
TO
F
IEL
D DR
ILL
H
OL
E T
HROUGH
PIPE.
OR
MAINT
EN
ANCE
W
A
R
N
I
N
G
:
DISCON
NECT
P
OW
ER
B
E
FOR
E
INS
T
ALLA
TION
CIMARRON
LE
D
FIX
TU
RE
SCRE
W
SAVE THESE INSTRUCTIONS
CIMARRON CL1 MAF INSTALLATION INSTRUCTIONS
1
. MOUNTING
MAST ARM
FITTER
TO FIXTURE ARM
AND TO MAST ARM PIPE
Remove Arm Cover by removing the (4) Screws.
Attach Fixture to
Mast Arm Fitter
with (2) ½” Hex Bolts,
Lockwashers
and Flatwashers
.
Torque bolts to
approx. 42 Ft
-
Lbs.
Engage (4) 3/8
-
16 X ¾” Set
-
screws to the cast
Mast Arm
Fitter.
Slip Arm Fitter onto
Mast
Arm and adjust Fixture orientation whil
e tightening the (4) Set
-
screws
.
After Leveling the Fixture attached to the
Mast
Arm, use hole
s on each side of
Mast Arm
Fitter to Field Drill
13/32” dia.
hole through the
Mast
Pipe Arm.
Remove Arm Fitter
and Fixture
from Mast Arm
Pipe
and Pull the supply wires from Mast Arm Pipe
through Mast Arm Fitter and into the Fixture Arm.
Slip
Mast
Arm Fitter
with Fixture
back onto the Mast Arm
Pipe
, Install the 4
”
l
ong Bolt
and tighten the
(4) Set
-
screws
to approx 18 Ft
-
Lbs.
S
ecure
4”
Bolt
with Flatwasher, Lockwasher, and Nut (Hardware Included)
.
Torque the Bolt and Nut to
approx. 20 Ft
-
Lbs.
WARNING:
FAILURE TO INSTALL THE LONG BOLT COULD POSSIBLY ALLOW THE FI
XTURE TO
ROTATE OR DISENGAGE FROM THE PIPE ARM.
AR
M C
OVE
R
M
AS
T
AR
M FITT
ER
M
AST A
RM
PIPE
F
LAT
W
AS
HER
, LO
CKW
AS
HER
,
NUT
3/
8"
SET-SCREWS
4"
LON
G BOL
T
2
.
WIRING
(See Fig.
2
)
POWER MUST BE OFF.
(WIRING MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN)
Wire service leads to fixture power leads according to local
and National Electric Codes.
Luminaire
is equipped with
u
niversal voltage driver
s
capab
le of 120V
-2
77V input
.
A
n optio
nal 347/480 V input transformer is available.
Wire connections to be made inside
A
rm with Fix
ture Wires and Supply Wires (by others).
For direct wire connections, connect ground wire to green
wire,
c
onnect
black to black and
white to
neutral then push connections
back inside
Arm and attach Arm Cover.
See Installation Instructions for Cimarron LED
, P/N
93034033
.
FIGUR
E
2
ARM
C
OVE
R
REM
OVE
D
ARM
FIX
TU
RE WIR
ES
SU
PP
LY WIR
ES
M
AS
T
AR
M FITT
ER
701 M
il
l
ennium
Boul
eva
rd
Gre
en
v
il
le
,
S
C
29607
(8
6
4)
67
8-
1000
www.
spau
lding-ltg.
co
m
9303760
2 REV B