WPEA-352ACNRB WPEA-352ACNRBI Manual 1
1.PRODUCT INTRODUCTION Standard IEEE802.11ac/a/b/g/n Chipset solution QCA9880-BR4A Radio stream [Note1] 3T3R Antenna type / connector. External with IPEX connector Bus Interface PCI Express Form Factor Mini-PCIe 802.11b: 11, 5.5, 2, 1 Mbps; 802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11a: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n: MCS 0 to 15 for HT20MHz MCS 0 to 15 for HT40MHz Data Rate 802.11ac: MCS 0 to 8 for HT20MHz MCS 0 to 9 for HT40MHz MCS 0 to 9 for HT80MHz 1.
802.11a: 14dBm@54Mbps 802.11b: 20dBm@11Mbps 802.11g: 16dBm@54Mbps Transmit Output Power (Tolerance: +/-2dBm) 802.11gn HT20: 15dBm@MCS7 802.11gn HT40: 15dBm@MCS7 802.11an HT20: 13dBm@MCS7 802.11an HT40: 13dBm@MCS7 802.11ac VHT80: 10dBm@MCS9 802.11a: ≤-73dBm@54Mbps 802.11b: ≤-86dBm@11Mbps 802.11g: ≤-73dBm@54Mbps Receiver Sensitivity 802.11gn HT20: ≤-70dBm@MCS7 802.11gn HT40: ≤-67dBm@MCS7 802.11an HT20: ≤-71dBm@MCS7 802.11an HT40: ≤-68dBm@MCS7 802.11ac VHT80: ≤-58dBm@MCS9 Operating Voltage DC 3.
2. HARDWARE SPECIFICATION 2.1 Hardware Dimension Dimension: 50.8mm * 29.85mm * 4.1mm(±0.
2.3 Pin Assignment The following section illustrate signal pin-outs for the system connector. Pin# Pin Name Description Pin# 2 +3.3V 4 GND GND 6 No Connection - No Connection - No Connection - No Connection - No Connection - - 1 WAKE_L(NA) Output and open Drain active Low signal. This signal is used to request that the system return from a sleep/suspended state to service a function initiated wake event.
functional reset to the card PERn0 23 PCI Express x1 data interface: one differential +3.3V +3.
* OPT: Optional (Depends on S/W and H/W design of the module and customer platform main board, functionalities of end devices and drivers.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
The OEM integrator is still responsible for 1. ensuring that the end-user has no manual instructions to remove or install module 2. the FCC compliance requirement of the end product, which integrates this module. 3. Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment authorizations (e.g. Verification, Doc) of the host device to be addressed by the integrator/manufacturer. 4.
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. This radio transmitter [IC: 6158A-WPEA352ACNB] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé.
Japan Antenna List # Brand Model Connector Type 5GHz Type 2.4GHz Band 1 1 Walsin RFDPA131000SBLB808 I-Pex Dipole 2 Cortec AN2450-5511BRS I-Pex Dipole 3 SANSEI ANTDP-027A0 I-Pex Dipole 1.3 4 Taoglas MA231.LBC.002 I-Pex Flat Bar 5 WIESON GPOT113-020A I-Pex Dipole 6 Cortec AN2450-16HM01BRS I-Pex Dipole 7 ARISTOTLE RFA-25-AP252-70-500 I-Pex PCB 8 ARISTOTLE RFA-25-AP287-4B-350F I-Pex PCB 3.
