Wireless-N Broadband AP / Router Model Name: WRTR-501 for SparkLAN Quick Installation Guide Version 1.
Table of Contents English 1. Before Installation .............................................................................................................................2 2. Hardware Installation ........................................................................................................................3 3. Configure your computer’s TCP/IP Settings......................................................................................4 4. Configure your AP ....................................
1. Before Installation Thank you for purchasing the Wireless 11n AP Router. This guide will help you set-up and configure your AP with easy-to-follow instructions. For more detailed or advanced settings, please refer to the User Manual on the CD-ROM. Package Contents Please make sure you have the following in the box: ♦ ♦ ♦ ♦ ♦ WRTR-501 Wireless-N Broadband AP Router Multi-Language Quick Installation Guide User Manual CD-ROM Three dipole 1.
2. Hardware Installation 1. Power off your network devices. 2. Locate an optimum location for the AP. The best place for the AP is usually at the center of your wireless network, with line of sight to all of your wireless devices. 3. Adjust the antennas. Normally, higher location of your AP may get better performance. 4. Using a standard Ethernet network cable, connect to the AP’s Ethernet port to your local network. 5. Connect the AC power adapter to the AP's Power port.
3. Configure your computer’s TCP/IP Settings Windows 2000/XP 1. 2. 3. Click Start; click Settings and then click on the Control Panel. Double-Click the Network Connection icon. Right-Click on the Local Area Connection icon and then click on Properties. The Local Area Connection Properties windows will appear. 4. Under the General Configuration Tab, locate and select TCP/IP with the corresponding network card, then click Properties. The Internet Protocol (TCP/IP) Properties window will appear.
. Now your computer is ready to access and configure the AP. Windows VISTA 1. Click Start Æ Control Panel, then Network and Internet Æ Manage network connections. 2. Right-Click on the Local Area Connection icon and then click on Properties. The Local Area Connection Properties windows will appear. 3. Under the Networking Configuration Tab, locate and select Internet Protocol Version4 (TCP/IPv4) with the corresponding network card, then click Properties.
4. 5. Click on Use the following IP Address and enter IP Address: 192.168.1.10 Subnet Mask: 255.255.255.0 Default gateway: 192.168.1.1 Now your computer is ready to access and configure the AP. NOTE : The default IP address setting for the AP is a class C IP address (192.168.1.1 / 255.255.255.0). Please make sure that the current workstation is following the class C IP address range, from 192.168.1.2 to 192.168.1.
4. Configure your AP 1. 2. Open your web browser, type http://192.168.1.1 in the Address bar, and press Enter. An authentication window will appear. Enter the username and password, and then click OK. By default, please leave blank in username and type admin in password. 3. Click “Save Settings” button to finish the Setup if you have something change. The following screen would appear to notify you the system is rebooting. All changes will be taken effect while reboot procedure is completed. 4.
z Win2000, WinXP, WinVISTA: type the “ ipconfig “ on your windows Command Prompt. Once you got the IP address, subnet mask and default gateway, that means your computer already connected to local network. For detail configuration of this AP, please refer to the CD-ROM.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.
Česky [Czech] [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
[Polish] Português [Portuguese ] Slovensko [Slovenian] Slovensky [Slovak] zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. [Nome do fabricante] declara que este [tipo de equipamento] está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. [Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.