User's Manual

ManualsBrandsSparkLAN Communications ManualsElectronics802.11n 3T3R Mini PCIe Module

WPEA-127NI

PRODUCT SPECIFICATION

Standard IEEE802.11 abgn

Chipset Atheros AR9390-AL1B

Radio stream [Note1] 3T3R

Antenna Type / con. 3 U.FL connectors (diversity ant)

Bus Interface PCI Express

Form Factor Mini PCIe

Data Rate

802.11b: 11, 5.5,2,1Mbps

802.11g: 54, 48, 36, 24, 18, 12, 9, 6Mbps

802.11a: 54, 48, 36, 24, 18, 12, 9, 6 Mbps

802.11n: MCS 0 to 23 for HT20MHz

MCS 0 to 23 for HT40MHz

Media Access Control CSMA/CA with ACK

Spreading /Modulation

Techniques

802.11a: OFDM (BPSK, QPSK, 16-QAM, 64-QAM)

802.11b: DSSS (DBPSK, DQPSK, CCK)

802.11g: OFDM (BPSK,QPSK,16-QAM,64-QAM)

802.11n: OFDM (BPSK,QPSK,16-QAM,64-QAM)

Frequency Range [Note2]

2.4GHz

11b/g/n: 2.400 ~ 2.4835GHz

5GHz

11a/n: 5.150GHz ~ 5.825GHz

Transmit Output Power

(Tolerance: +/-2dBm)

802.11a: 11dBm ± 2dBm@54Mbps

802.11b: 19dBm ± 2dBm@11Mbps

802.11g: 16dBm ± 2dBm@54Mbps

802.11gn HT20: 15dBm ± 2dBm@MCS7

802.11gn HT40: 15dBm ± 2dBm@MCS7

802.11an HT20: 11dBm ± 2dBm@MCS7

802.11an HT40: 11dBm ± 2dBm@MCS7

Receiver Sensitivity

(Tolerance: +/-2dBm)

802.11a: -78dBm ± 2dBm@54Mbps

802.11b: -95dBm ± 2dBm@11Mbps

802.11g: -79dBm ± 2dBm@54Mbps

802.11gn HT20: -76dBm ± 2dBm@MCS7

802.11gn HT40: -74dBm ± 2dBm@MCS7

802.11an HT20: -75dBm ± 2dBm@MCS7

802.11an HT40: -72dBm ± 2dBm@MCS7

Operating Voltage 3.3V ±10% I/O supply voltage

Power Consumption

TX Mode: 970mA

RX Mode: 300mA

Associated Idle: 50 mA

Temperature Range -40~+80°C (Operating) [Note3]

Humidity (non-condensing) 20~80%(Operating), 5~95%(Storing) [Note3]

Security WEP / WPA / WPA2

OS supported Windows XP/Vista/Win7, Linux

Note:

1. For Radio stream with diversity or MIMO design, all RF connectors on the module must be fitting

antennas in order to guarantee the module performance.

2. The frequency range need to local regulations.

3. The storing condition is only for product functionality, no included for parts appearance.

Summary of content (8 pages)

PAGE 1
WPEA-127NI PRODUCT SPECIFICATION Standard Chipset Radio stream [Note1] Antenna Type / con. Bus Interface Form Factor Data Rate Media Access Control Spreading /Modulation Techniques Frequency Range [Note2] Transmit Output Power (Tolerance: +/-2dBm) Receiver Sensitivity (Tolerance: +/-2dBm) Operating Voltage Power Consumption IEEE802.11 abgn Atheros AR9390-AL1B 3T3R 3 U.FL connectors (diversity ant) PCI Express Mini PCIe 802.11b: 11, 5.5,2,1Mbps 802.11g: 54, 48, 36, 24, 18, 12, 9, 6Mbps 802.
PAGE 2
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 3
This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
PAGE 4
Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence.
PAGE 5
This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
PAGE 6
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization.
PAGE 7
Manuel d'information à l'utilisateur final L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce manuel.
PAGE 8
interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter (IC: 6158A-WPEA127NI / Model: WPEA-127NI) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated.