Datasheet
Table Of Contents
- General Description
- Key Features
- Applications
- System Diagrams
- Contents
- Figures
- Tables
- Legal
- Product Family
- 1 Terms and Definitions
- 2 Block Diagram
- 3 Pinout
- 4 Characteristics
- 5 Functional Description
- 5.1 Features Description
- Driving LRA and ERM Actuators
- Automatic LRA Resonant Frequency Tracking
- Wideband LRA Support
- I2C and PWM Input Streaming
- Low Latency I2C/GPI Wake-Up from IDLE State
- Three GPI Sequence Triggers for up to Six Independent Haptic Responses
- On-Board Waveform Memory with Amplitude, Time, and Frequency Control
- Active Acceleration and Rapid Stop for High-Fidelity Haptic Feedback
- Continuous Actuator Diagnostics and Fault Handling
- No Software Requirements with Embedded Operation
- Differential Output Drive
- Current Driven System
- Configurable EMI Suppression
- Automatic Short Circuit Protection
- Ultra-Low Power Consumption with State Retention
- Ultra-Low Latency in STANDBY State
- Supply Monitoring, Reporting, and Automatic Output Limiting
- Open- and Closed-Loop Modes
- Open-Loop Sine/Custom Wave Drive Support
- Small Solution Footprint
- Additional Features
- 5.2 Functional Modes
- 5.3 Resonant Frequency Tracking
- 5.4 Active Acceleration and Rapid Stop
- 5.5 Wideband Frequency Control
- 5.6 Device Configuration and Playback
- 5.7 Advanced Operation
- 5.7.1 Frequency Tracking
- 5.7.2 Rapid Stop
- 5.7.3 Initial Impedance Update
- 5.7.4 Amplitude PID
- 5.7.5 Wideband Operation
- 5.7.6 Custom Waveform Operation
- 5.7.7 Embedded Operation
- 5.7.8 Polarity Change Reporting for Half-Period Control in DRO Mode
- 5.7.9 Loop Filter Configuration
- 5.7.10 UVLO Threshold
- 5.7.11 Edge Rate Control
- 5.7.12 Double Output Current Range
- 5.7.13 Supply Monitoring, Reporting, and Automatic Output Limiting
- 5.7.14 BEMF Fault Limit
- 5.7.15 Increasing Impedance Detection Accuracy
- 5.7.16 Frequency Pause during Rapid Stop
- 5.7.17 Frequency Pause during Rapid Stop
- 5.7.18 Coin ERM Operation
- 5.8 Waveform Memory
- 5.9 General Data Format
- 5.10 I2C Control Interface
- 5.1 Features Description
- 6 Register Overview
- 7 Package Information
- 8 Ordering Information
- 9 Application Information
- 10 Layout Guidelines
DA7280
LRA/ERM Haptic Driver with Multiple Input Triggers,
Integrated Waveform Memory and Wideband Support
Datasheet
Revision 3.0
30-Jul-2019
CFR0011-120-00
32 of 76
© 2019 Dialog Semiconductor
Output starts
switching
Write
OPERATION_MODE = 4
IDLE/STANDBY
Sequence
playback
Write
SEQ_DONE_M = 1
to clear register and
nIRQ
DA7280
ready to
play next
sequence
Sequence is
continued
Are
PS_SEQ_ID and
PS_SEQ_LOOP already
configured?
Configure the
PS_SEQ_LOOP
register
Yes
No
Trigger via GPIx
or I
2
C
SEQ_CONTINUE = 1?
Select a sequence
via PS_SEQ_ID
No
Yes
OPERATION_MODE = 4?
Yes
No
nIRQ = 0 and
SEQ_DONE_M = 1
Sequence playback is
complete and output
stops switching
Are
GPIx_SEQUENCE_ID,
GPIx_MODE, and
GPIx_POLARITY already
configured?
Yes
No
Configure
GPIx_SEQUENCE_ID
Configure GPIx_MODE
Configure
GPIx_POLARITY
SEQ_CONTINUE
can be set if
required during
playback
Can be skipped
for subsequent
sequence
playbacks
Figure 16: Operation in ETWM Mode