Manual
Table Of Contents
- Title
- Contents
- 1 Integration manual structure
- 2 System description
- 3 Receiver functionality
- 3.1 Receiver configuration
- 3.1.1 Changing the receiver configuration
- 3.1.2 Default GNSS configuration
- 3.1.3 Default interface settings
- 3.1.4 Basic receiver configuration
- 3.1.5 Differential timing mode configuration
- 3.1.6 Legacy configuration interface compatibility
- 3.1.7 Navigation configuration
- 3.2 Geofencing
- 3.3 Logging
- 3.4 Communication interfaces
- 3.5 Predefined PIOs
- 3.6 Antenna supervisor
- 3.7 Multiple GNSS assistance (MGA)
- 3.8 Clocks and time
- 3.9 Timing functionality
- 3.10 Security
- 3.11 u-blox protocol feature descriptions
- 3.12 Forcing a receiver reset
- 3.13 Firmware upload
- 3.1 Receiver configuration
- 4 Design
- 5 Product handling
- Appendix
- Related documents
- Revision history
- Contact
ZED-F9T-Integration manual
3.1.5.1 RTCM corrections
RTCM is a binary data protocol for communication of GNSS correction information. The ZED-F9T
high accuracy timing receiver supports RTCM as specified by RTCM 10403.3, Differential GNSS
(Global Navigation Satellite Systems) Services – Version 3 (October 7, 2016).
The RTCM specification is currently at version 3.3 and RTCM version 2 messages are not supported
by this standard.
To modify the RTCM input/output settings, see the configuration section in the u-blox ZED-F9T
Interface description [2].
3.1.5.2 List of supported RTCM input messages
Message type Description
RTCM 1005 Stationary RTK reference station ARP
RTCM 1077 GPS MSM7
RTCM 1087 GLONASS MSM7
RTCM 1097 Galileo MSM7
RTCM 1127 BeiDou MSM7
RTCM 1230 GLONASS code-phase biases
RTCM 4072.1 Additional reference station information (u-blox proprietary RTCM Message)
Table 5: ZED-F9T supported input RTCM version 3.3 messages
3.1.5.3 List of supported RTCM output messages
Message type Description
RTCM 1005 Stationary RTK reference station ARP
RTCM 1077 GPS MSM7
RTCM 1087 GLONASS MSM7
RTCM 1097 Galileo MSM7
RTCM 1127 BeiDou MSM7
RTCM 1230 GLONASS code-phase biases
RTCM 4072.1 Additional reference station information (u-blox proprietary RTCM Message)
Table 6: ZED-F9T supported output RTCM version 3.3 messages
3.1.5.4 Timing receiver position
Time mode is a special receiver mode where the position of the receiver is known and fixed and only
the time and frequency is calculated using all available satellites. This mode allows for maximum
time accuracy, for single-SV solutions, and also for using the receiver as a stationary reference
station.
In order to use time mode, the receiver's position must be known as exactly as possible. Errors in the
fixed position will translate into time errors depending on the satellite constellation.
The following procedures can be used to initialize the timing receiver position:
• Using built-in survey-in procedure to estimate the position.
• Entering coordinates independently generated or taken from an accurate position such as a
survey marker.
3.1.5.4.1 Survey-in
Survey-in is a procedure that is carried out prior to entering Time mode. It estimates the receiver
position by building a weighted mean of all valid 3D position solutions.
Two major parameters are required when configuring:
UBX-19005590 - R05
3 Receiver functionality Page 13 of 87
C1-Public Early production information