User Manual

Apollo3 Blue Datasheet
DS-A3-0p9p1 Page 470 of 909 2019 Ambiq Micro, Inc.
All rights reserved.
7 GPIO33INTD 0x0 RW
GPIO33 interrupt direction.
nCELOW = 0x0 - FNCSEL = 0x1 - nCE polarity active low
nCEHIGH = 0x1 - FNCSEL = 0x1 - nCE polarity active high
INTDIS = 0x0 - FNCSEL != 0x1, INCFG = 1 - No interrupt on GPIO transi-
tion
INTBOTH = 0x1 - FNCSEL != 0x1, INCFG = 1 - Interrupt on either low to
high or high to low GPIO transition
INTLH = 0x0 - FNCSEL != 0x1, INCFG = 0 - Interrupt on low to high GPIO
transition
INTHL = 0x1 - FNCSEL != 0x1, INCFG = 0 - Interrupt on high to low GPIO
transition
6:5
GPIO33OUT-
CFG
0x0 RW
GPIO33 output configuration.
DIS = 0x0 - FNCSEL = 0x3 - Output disabled
PUSHPULL = 0x1 - FNCSEL = 0x3 - Output is push-pull
OD = 0x2 - FNCSEL = 0x3 - Output is open drain
TS = 0x3 - FNCSEL = 0x3 - Output is tri-state
M0nCE2 = 0x0 - FNCSEL = 0x1 - IOM0 nCE, Channel 2
M1nCE2 = 0x1 - FNCSEL = 0x1 - IOM1 nCE, Channel 2
M2nCE2 = 0x2 - FNCSEL = 0x1 - IOM2 nCE, Channel 2
M5nCE2 = 0x3 - FNCSEL = 0x1 - IOM5 nCE, Channel 2
4 GPIO33INCFG 0x0 RW
GPIO33 input enable.
READ = 0x0 - Read the GPIO pin data
RDZERO = 0x1 - INTD = 0 - Readback will always be zero
READEN = 0x1 - INTD = 1 - Read the GPIO pin data
3 GPIO32INTD 0x0 RW
GPIO32 interrupt direction.
nCELOW = 0x0 - FNCSEL = 0x1 - nCE polarity active low
nCEHIGH = 0x1 - FNCSEL = 0x1 - nCE polarity active high
INTDIS = 0x0 - FNCSEL != 0x1, INCFG = 1 - No interrupt on GPIO transi-
tion
INTBOTH = 0x1 - FNCSEL != 0x1, INCFG = 1 - Interrupt on either low to
high or high to low GPIO transition
INTLH = 0x0 - FNCSEL != 0x1, INCFG = 0 - Interrupt on low to high GPIO
transition
INTHL = 0x1 - FNCSEL != 0x1, INCFG = 0 - Interrupt on high to low GPIO
transition
2:1
GPIO32OUT-
CFG
0x0 RW
GPIO32 output configuration.
DIS = 0x0 - FNCSEL = 0x3 - Output disabled
PUSHPULL = 0x1 - FNCSEL = 0x3 - Output is push-pull
OD = 0x2 - FNCSEL = 0x3 - Output is open drain
TS = 0x3 - FNCSEL = 0x3 - Output is tri-state
M0nCE1 = 0x0 - FNCSEL = 0x1 - IOM0 nCE, Channel 1
M1nCE1 = 0x1 - FNCSEL = 0x1 - IOM1 nCE, Channel 1
M2nCE1 = 0x2 - FNCSEL = 0x1 - IOM2 nCE, Channel 1
MSPInCE1 = 0x3 - FNCSEL = 0x1 - MSPI nCE, Channel 1
0 GPIO32INCFG 0x0 RW
GPIO32 input enable.
READ = 0x0 - Read the GPIO pin data
RDZERO = 0x1 - INTD = 0 - Readback will always be zero
READEN = 0x1 - INTD = 1 - Read the GPIO pin data
Table 660: CFGE Register Bits
Bit Name Reset RW Description