Manualshelf

User Manual

ManualsBrandsSparkFun Electronics ManualsDevelopment Boards & KitsApollo3 Blue Edge Development Board
461462463464465466467468469470
Apollo3 Blue Datasheet
DS-A3-0p9p1 Page 465 of 909 2019 Ambiq Micro, Inc.
All rights reserved.
11 GPIO26INTD 0x0 RW
GPIO26 interrupt direction.
nCELOW = 0x0 - FNCSEL = 0x1 - nCE polarity active low
nCEHIGH = 0x1 - FNCSEL = 0x1 - nCE polarity active high
INTDIS = 0x0 - FNCSEL != 0x1, INCFG = 1 - No interrupt on GPIO transi-
tion
INTBOTH = 0x1 - FNCSEL != 0x1, INCFG = 1 - Interrupt on either low to
high or high to low GPIO transition
INTLH = 0x0 - FNCSEL != 0x1, INCFG = 0 - Interrupt on low to high GPIO
transition
INTHL = 0x1 - FNCSEL != 0x1, INCFG = 0 - Interrupt on high to low GPIO
transition
10:9
GPIO26OUT-
CFG
0x0 RW
GPIO26 output configuration.
DIS = 0x0 - FNCSEL = 0x3 - Output disabled
PUSHPULL = 0x1 - FNCSEL = 0x3 - Output is push-pull
OD = 0x2 - FNCSEL = 0x3 - Output is open drain
TS = 0x3 - FNCSEL = 0x3 - Output is tri-state
M3nCE3 = 0x0 - FNCSEL = 0x1 - IOM3 nCE, Channel 3
M4nCE3 = 0x1 - FNCSEL = 0x1 - IOM4 nCE, Channel 3
M5nCE3 = 0x2 - FNCSEL = 0x1 - IOM5 nCE, Channel 3
M1nCE3 = 0x3 - FNCSEL = 0x1 - IOM1 nCE, Channel 3
8 GPIO26INCFG 0x0 RW
GPIO26 input enable.
READ = 0x0 - Read the GPIO pin data
RDZERO = 0x1 - INTD = 0 - Readback will always be zero
READEN = 0x1 - INTD = 1 - Read the GPIO pin data
7 GPIO25INTD 0x0 RW
GPIO25 interrupt direction.
nCELOW = 0x0 - FNCSEL = 0x1 - nCE polarity active low
nCEHIGH = 0x1 - FNCSEL = 0x1 - nCE polarity active high
INTDIS = 0x0 - FNCSEL != 0x1, INCFG = 1 - No interrupt on GPIO transi-
tion
INTBOTH = 0x1 - FNCSEL != 0x1, INCFG = 1 - Interrupt on either low to
high or high to low GPIO transition
INTLH = 0x0 - FNCSEL != 0x1, INCFG = 0 - Interrupt on low to high GPIO
transition
INTHL = 0x1 - FNCSEL != 0x1, INCFG = 0 - Interrupt on high to low GPIO
transition
6:5
GPIO25OUT-
CFG
0x0 RW
GPIO25 output configuration.
DIS = 0x0 - FNCSEL = 0x3 - Output disabled
PUSHPULL = 0x1 - FNCSEL = 0x3 - Output is push-pull
OD = 0x2 - FNCSEL = 0x3 - Output is open drain
TS = 0x3 - FNCSEL = 0x3 - Output is tri-state
M3nCE2 = 0x0 - FNCSEL = 0x1 - IOM3 nCE, Channel 2
M4nCE2 = 0x1 - FNCSEL = 0x1 - IOM4 nCE, Channel 2
M5nCE2 = 0x2 - FNCSEL = 0x1 - IOM5 nCE, Channel 2
M0nCE2 = 0x3 - FNCSEL = 0x1 - IOM0 nCE, Channel 2
4 GPIO25INCFG 0x0 RW
GPIO25 input enable.
READ = 0x0 - Read the GPIO pin data
RDZERO = 0x1 - INTD = 0 - Readback will always be zero
READEN = 0x1 - INTD = 1 - Read the GPIO pin data
Table 658: CFGD Register Bits
Bit Name Reset RW Description