LMV358 datasheet

www.ti.com
Electrical Characteristics
LMV321 SINGLE, LMV358 DUAL
LMV324 QUAD, LMV324S QUAD WITH SHUTDOWN
LOW-VOLTAGE RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS
SLOS263T – AUGUST 1999 – REVISED SEPTEMBER 2007
V
CC+
= 5 V, at specified free-air temperature (unless otherwise noted)
PARAMETER TEST CONDITIONS T
A
(1)
MIN TYP
(2)
MAX UNIT
25 ° C 1.7 7
V
IO
Input offset voltage mV
Full range 9
Average temperature
α
VIO
coefficient of input offset 25 ° C 5 μ V/ ° C
voltage
25 ° C 15 250
I
IB
Input bias current nA
Full range 500
25 ° C 5 50
I
IO
Input offset current nA
Full range 150
Common-mode rejection
CMRR V
CM
= 0 to 4 V 25 ° C 50 65 dB
ratio
Supply-voltage V
CC
= 2.7 V to 5 V, V
O
= 1 V,
k
SVR
25 ° C 50 60 dB
rejection ratio V
CM
= 1 V
0 – 0.2
Common-mode input
V
ICR
CMRR ≥ 50 dB 25 ° C V
voltage range
4.2 4
25 ° C V
CC
– 300 V
CC
– 40
High level
Full range V
CC
– 400
R
L
= 2 k Ω to 2.5 V
25 ° C 120 300
Low level
Full range 400
V
O
Output swing mV
25 ° C V
CC
– 100 V
CC
– 10
High level
Full range V
CC
– 200
R
L
= 10 k Ω to 2.5 V
25 ° C 65 180
Low level
Full range 280
25 ° C 15 100
Large-signal differential
A
VD
R
L
= 2 k Ω V/mV
voltage gain
Full range 10
Sourcing, V
O
= 0 V 5 60
Output short-circuit
I
OS
25 ° C mA
current
Sinking, V
O
= 5 V 10 160
25 ° C 130 250
LMV321I
Full range 350
25 ° C 210 440
I
CC
Supply current LMV358I (both amplifiers) μ A
Full range 615
25 ° C 410 830
LMV324I/LMV324SI
(all four amplifiers)
Full range 1160
B
1
Unity-gain bandwidth C
L
= 200 pF 25 ° C 1 MHz
Φ
m
Phase margin 25 ° C 60 deg
G
m
Gain margin 25 ° C 10 dB
Equivalent input
V
n
f = 1 kHz 25 ° C 39 nV/ √ Hz
noise voltage
Equivalent input
I
n
f = 1 kHz 25 ° C 0.21 pA/ √ Hz
noise current
SR Slew rate 25 ° C 1 V/ μ s
(1) Full range T
A
= – 40 ° C to 85 ° C for I temperature and – 40 ° C to 125 ° C for Q temperature.
(2) Typical values represent the likely parametric nominal values determined at the time of characterization. Typical values depend on the
application and configuration and may vary over time. Typical values are not ensured on production material.
6 Submit Documentation Feedback Copyright © 1999 – 2007, Texas Instruments Incorporated