REQUIRED TOOLS AND MATERIALS: • 2 Capable Adults Universal Elevator Mount Owners Manual Customer Service Center • N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A. • Carpenter’s Level • 15’ Tape Measure Adult Assembly Required. This manual, accompanied by sales receipt, should be saved and kept on hand as a convenient reference, as it contains important information about your model. • Pencil • Drill and Drill Bit (3/8") • Step Ladder 8ft. (2.
SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this system without following the instructions carefully. Proper and complete assembly, use and supervision is essential for proper operation and to reduce the risk of accident or injury.
IMPORTANT! Remove all contents from box. PRODUCT REGISTRATION: Please remember to complete your product registration form online at: www.huffysports.com/customer_support/product_registration. For more information on assembly, placement, proper use, and maintenance, visit The American Basketball Council website at http://www.smarthoops.com. NOTICE TO ASSEMBLERS Adult Assembly Required. Dispose of ALL packaging materials promptly. As with all products, periodically inspect for loose small parts.
PARTS LIST - See Hardware Identifier Item Qty. Part No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 2 2 6 1 1 5 1 9 12 10 6 1 1 2 4 3 1 1 205807 202675 203589 201129 240017 205678 588000 206340 203218 202651 203099 509000 240027 265500 202587 206269 908525 908528 Item Qty. Part No. Description U-Bolt, Round 3/8-16 x 4.68 Clamp, Saddle Bolt, Hex Head, 5/16-18 x 1-1/4” Long Spacer, 1.
HARDWARE IDENTIFIER - ACTUAL SIZE (STEEL SPACERS) #4 (1) #16 (3) #31 (2) HARDWARE IDENTIFIER - ACTUAL SIZE (PLASTIC SPACERS, CAPS, CLIPS AND OTHER) #15 (4) #25 (2) HARDWARE IDENTIFIER (NOT ACTUAL SIZE) #2 (2) #20 (2) 21 (1) #19 (1) #18 (1) #23 (2) #30 (4) #22 (1) HEIGHT ADJUSTMENT #17 (1) TO ADJUST BACKBOARD: Position looped end of crank onto hook as shown.
BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates. Carefully rock them in a circular motion to ream out any excess paint from holes if necessary. Not all parts shown are included with every system. SECTION A: ASSEMBLE THE ELEVATOR MOUNT TO DIFFERENT MOUNT SURFACES (POLE, WALL & ROOF) Identify elevator tubes (30).
ASSEMBLE THE ELEVATOR MOUNT TO A SQUARE POLE At a position near the ground surface, assemble pole bracket (17) to square pole using u-bolts (29), washers (10) and nuts (8) as shown. 1. A. Attach jack support brackets (18 & 19) to pole bracket (17) using bolts (3), washers (9) and nuts (11) as shown. 29 17 10 8 B.
ASSEMBLE THE ELEVATOR MOUNT TO A ROUND POLE At a position near the ground surface, assemble pole bracket (17) to round pole using u-bolts (1), clamps (2), washers (34) and nuts (33) as shown. 2. A. Attach jack support brackets (18 & 19) to pole bracket (17) using bolts (3), washers (9) and nuts (11) as shown. 1 2 17 34 33 B.
ASSEMBLE THE ELEVATOR MOUNT TO A WALL OR FLAT SURFACE Secure pole bracket (17) to flat solid surface. Install bolt heads outside for safety reasons. 3. 17 A. Attach jack support brackets (18 & 19) to pole bracket (17) using bolts (3), washers (9) and nuts (11) as shown. Not Included with Hardware Not Included with Hardware B.
ASSEMBLE THE ELEVATOR MOUNT TO A FLAT OR ANGLED ROOF WARNING! A solid mounting base and/or surface, capable of withstanding normal recreational use forces, must be provided by the customer. A reliable carpenter or building contractor should be consulted if there are questions regarding this procedure. WARNING! Carefully inspect mounting area for structural integrity and hidden electrical wiring.
FLAT OR ANGLED ROOF (continued) 4. B. Drill holes in roof. Position angled brackets and secure to roof. 4. 23 C. 27 & 26 Keep assembly upright and position struts (23) on desired location on roof approx. 26”-30” (66-76 cm) apart. Level in all directions. Mark and drill holes. Secure struts in place. Not Included with Hardware WARNING! 23 All mounting points should be sealed to prevent leaks and water damage" Note position of angle brackets (26 & 27) in relation to pole bracket per style roof.
SECTION B: FROM THIS SECTION FORWARD THE ASSEMBLIES ARETHE SAME FOR SQUARE AND ROUND POLE, WALL MOUNT, AND ROOF MOUNT 31 1. Attach elevator tubes (30) to the jack support brackets (18 & 19) using bolts (6), washers (10), spacers (31 & 32) and nuts (8) as shown.
2. Attach height decal (28) on screw jack (24). Align lower edge of decal (28) with screw jack bottom. 28 21 Place cover (21) over screw jack (24). Insert spacer (16) into screw jack assembly (24) as shown. Install screw jack assembly (24) using bolts (6 & 14), washer (10) and nut (8) as shown.
BACKBOARD MOUNTING ATTACH A COMPOSITE STYLE BACKBOARD (STYLE WILL VARY) ATTACH AN H-FRAME STYLE BACKBOARD (STYLE WILL VARY) 1. Attach backboard using hardware shown. Folow instructions that are packaged with backboard for specific assembly details. 1. Assemble backboard brackets (20) using bolt (5) spacer (4) and nut (13) as shown. Folow instructions that are packaged with backboard for specific assembly details. OR 20 13 20 4 5 16 8 6 2. Attach backboard using hardware shown.
BACKBOARD MOUNTING (continued) OR 3. ATTACH A STEEL-FRAMED STYLE BACKBOARD (STYLE WILL VARY) Attach backboard using hardware shown. Folow instructions that are packaged with backboard for specific assembly details. 6 25 15 6 15 8 15 15 25 8 HEIGHT ADJUSTMENT AND WARNING LABEL PLACEMENT NOTE: Adhere WARNING label (20) in a clearly visible place. TO ADJUST BACKBOARD: Position looped end of crank onto hook as shown. REGULATION RIM HEIGHT IS 10 FEET (3.05 m).
