Display System Owners Manual Customer Service Center • N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A. Model 89231CA REQUIRED TOOLS AND MATERIALS: WARNING! • 2 Capable Adults READ AND UNDERSTAND OPERATOR'S MANUAL BEFORE USING THIS UNIT. • 2 Stepladders FAILURE TO FOLLOW OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR DAMAGE TO PROPERTY. • (2 each) Wrenches and/or Socket Wrenches and Sockets.
IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside. SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY. This unit is intended for display purposes only and should not be used for play. To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check entire box and inside all packing material for parts.
PARTS LIST (See Hardware Identifier) Item Qty. Part No. Description Item Qty. Part No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 2 2 2 2 2 1 8 4 8 2 10 3 4 4 200318 203223 908379 200533 ** 990062 908378 201611 205544 203063 ** 912006 203100 206987 203294 203309 Bracket, Reinforcement S/J Bolt, Carriage, 5/16-18 x 1" Board Bracket Spacer, Mounting Pole, 3.5" Rim Bolt,Hex-Flange, 5/16-18 x 3" Bolt, 5/16-18 x 1.
Install display boards in the marked locations. Each mounting location consists of a mounting pole stub with the following dimensions: Height = 8”, O.D. = 3 3/8”, I.D. = 3 1/8” (arrows indicate direction the board is facing).
Corner Location 3: REPLACE POLE 1. At corner location 3: remove the current 3" display pole from the mounting stub. A 4 CORNER CORNER CORNER CORNER 3 1 Secure the display pole by sliding the display wedges (12) into position as shown. To lock the display pole in place, tighten the hex-bolts (19). 24 24 3 CORNER 4 CORNER B Then, still at corner location 3, slide the 2.75” diameter pole end of the display pole (24) inside the moiunting stub. 19 12 12 19 12 1 19 CORNER CORNER 1.
Corner Location 1: STEEL FRAME ACRYLIC BACKBOARD ASSEMBLY Display Stand - Top View 4 CORNER CORNER 3 3" 3-1/2" 10 11 11 65246CA Open - No Board 27 77271CA 3-1/2" 3-1/2" 1 1. 4 CORNER CORNER 66281CA 4 2 18 Insert “T” bolt (18) through Slam Jam bracket (23) as shown. Secure Slam Jam bracket (23), extension arm (10) and mounting spacers (4) assemblies to backboard using bolt (7 ) and nut (11) as shown. 23 7 2. Attach board assembly to pole.
3. NOTE: • Fit rim (21) securely into bracket (23) as shown. • Install reinforcement bracket (1) onto “T” bolt (18) as shown. Tighten nut (17) until flush with end of "T" bolt (18) as shown here. • Install spring (16) onto “T” bolt (18) as shown. • Install special nut (17) and washer (15) onto “T” bolt (18). 21 17 18 NOTE: Peel protective film from surface of acrylic backboard prior to use. 4. 15 23 16 1 Install net (20) as shown. OUTSIDE VIEW A. B. C. D.
Corner Location 2: 48” SQUARE MOLDED PLASTIC BOARD ASSEMBLY Display Stand - Top View 4 11 CORNER CORNER 3 3" 3-1/2" 10 65246CA Open - No Board 25 77271CA 3-1/2" 3-1/2" 1 1. CORNER CORNER 66281CA 2 Insert “T” bolt (18) through Slam Jam bracket (23) as shown. Secure Slam Jam bracket (23) and extension arm (10) to backboard using bolt (7) and nut (11) as shown. 18 23 18 Tighten completely. 2. 7 7 Attach board assembly to pole.
3. • Fit rim (21) securely into bracket (23) as shown. • Install reinforcement bracket (1) onto “T” bolt (18) as shown. • Install spring (16) onto “T” bolt (18) as shown. • Install special nut (17) and washer (15) onto “T” bolt (18). NOTE: Tighten nut (17) until flush with end of "T" bolt (18) as shown here. 21 17 18 15 1 16 23 4. Install net (20) as shown. OUTSIDE VIEW A. B. C. D.
Corner Location 3: 44" TRAPEZOID MOLDED PLASTIC BOARD ASSEMBLY Display Stand - Top View 3" 3-1/2" Open - No Board 65246CA 66281CA 77271CA 3-1/2" 3-1/2" 1 1. CORNER CORNER 3 CORNER CORNER 4 2 Attach rim (6), backboard (26) and support brackets (3) to the mounting pad on the top pole using the bottom rim mounting bolts (8) as shown.
2. Install the top rim mounting bolts (8) as shown. Install support bracket mounting bolts (21) as shown. 3. 26 26 2 11 2 11 6 6 8 4. Install net (20) as shown. OUTSIDE VIEW A. B. C. D.
