Instruction Manual

ManualsBrandsSPACE ManualsSlush MachineSPACE SC-1 Slush Machine

INTRODUCTION

Model: SC-1，SC-2，SC-3

Congratulations ! You are the owner of not only the finest slush machines but

also the most versatile of its kind.

Please read all sections of this manual thoroughly to familiarize yourself with

all aspects of the unit.

INSTALLATION

Type Y attachment

If the power supply cord is damaged , it must be replaced by the manufacturer

NOTE: This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for their

safety.

Children should be supervised to ensure that they do not play with the

appliance.

or its service agent or a similar qualified person in order to avoid an hazard.

1. Remove the corrugated container and packing materials and keep them

for possible future use .

CAUTION! When handling the machine, never grip it by the tanks/

bowls

or evaporator cylinders. The manufacturer and supplier will NOT

be held responsible for any damages which may occur through

incorrect

handling.

2. Inspect the uncreated unit for any possible damage

1) If having any damage, please call the delivery carrier immediately.

2)If the power cord is damaged, it must be replaced by the manufacturer,

service agent or a qualified electrician in order to avoid any hazard.

Install the unit on a counter top that will support the combined weight of

the dispenser and product, bearing in mind what is stated in the preceding

point 1, CAUTION paragraph.

the dispensing side, a minimum of 15 cm (6”) of free space should be

4. When installing the unit, please leave adequate space. Facing the unit from

allowed at the rear and on each side of the machine.

5. Ensure that the foot pieces are screwed tightly into the base of the

Summary of content (9 pages)

PAGE 1
INTRODUCTION Model: SC-1，SC-2，SC-3 Congratulations ! You are the owner of not only the finest slush machines but also the most versatile of its kind. Please read all sections of this manual thoroughly to familiarize yourself with all aspects of the unit.
PAGE 2
machine . 6. Clean and sanitize the unit according to the instructions in this manual . See the “CLEANING” paragraph . 7. Fill the bowls (tanks) with the mix to the maximum level mark . Do not overfill . All food touching parts are safe for your health. The machine can be used to chill juice, coffee and make slush. After a business day, switch off the power and remove the mixture. Keep the mix fresh over night by storing it in a fridge. 8.
PAGE 3
“O” position- OFF: in the “O” position power is turned OFF to all functions Indicator light A B A、B、C--Switch C ON Display Screen 1--Slush 2--Juice OFF 2. A,B,C switches will be used during operation, you can adjust the temperature of the juice. The temperature is 3℃,5℃,,5℃,5℃,, 9℃,5℃,, 11℃,5℃, .It is factory set at 9 ℃,5℃,. 3 Refrigeration switch Operation: a. Set the power switch to ON position b.
PAGE 4
2) Light ON: Juice mode, only produce cold beverage When the Light is ON, the machine will start to work and stop when the temperature reached the required setting. 3) A,B,C switches will be used during the chilling of the beverage. You can adjust the juice temperature to 3℃,5℃,,5℃,5℃,,9℃,5℃,,11℃,5℃,.It is factory set at 9 ℃,5℃,. . 4.Separate Control Switch C A B A 、B、 C switch You will find switches at the right side panel of the machine which controls each bowl/tank separately. 1.
PAGE 5
2. Remove the cover from the bowl. 3.Remove the bowl by lifting its faucet side up and off the fastening hooks(fig.1)and side it out(fig.2)     figure 1 figure 2 4.Slide the outer spiral out (fig.3)and then the inner auger (fig.4)   f i gur e 2 f i gur e 1 f i gur e 12 5.Remove the bowl gasket from its seat(fig .
PAGE 6
Assembly: 1.Slide the drip tray into place. 2. Lubricate the faucet piston, inside auger and outer spiral (see points A,B and C of figure 7) only with the grease supplied by the manufacture or other “food grade approved ”lubricant. 3. Assemble the faucet by reversing the disassembly steps(fig.6) 4.Fit bowl gasket around its seat (fig.8)   Figure 8 NOTE: The largest brim if the gasket faces the rear wall. 4.
PAGE 7
 figure 10 figure 9  5.Push the bowl/tank towards the rear wall of the unit until it fits snugly around the gasket. The front fastening hooks must be properly engaged (fig.11). Use fresh mix to remove any remaining sanitizer from the bottom of the bowls/tanks. Drain this solution and do not rinse out the machine.   figure 11 SANITIZING Prepare a cleaning solution of sodium hypochlorite (1 spoon diluted with 2 liters of water ).
PAGE 8
-towards the left(counter clockwise)to obtain thicker product(the indicator F will go down in opening G) Note -To shorten slush recovery time and increase production, the bowl should be refilled after the product level is lower than half of the evaporator cylinder. -Before restarting the unit, ensure that no blocks of ice have formed, if so remove them before switching on the unit. Excessive Heating The dispenser must be able to emit heat.
PAGE 9
401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 Top Cover Lining-Top Cover Bowl/Tank Draw Valve Seal-Draw Valve Spring Handle Pivot Spring-Small Fixed Ring Outer Spiral Inside Auger Cover-Drip Pan/tray Drip Pan/Tray Display Board ON/OFF Button Front Panel Spring Bolt Accessory-Compressor Compressor Control/Main Board Electromagnetic Valve Chute-Control Board Regula