Instructions / Assembly

25004 / 27008
FAUTEUIL À INCLINAISON SYNCHRONISÉE
DES GENOUX
INSTRUCTIONS DE MONTAGE
© Office Star Products Juillet 2010
25004 / 27008
SYNCHRO KNEE TILT CHAIR
OPERATING INSTRUCTIONS
WARNING
1. Use this product only one person at a time.
2. Do not use this chair unless all bolts screws and knobs are
securely tightened.
3. Check that all bolts screws and knobs are tight every three months or
as needed.
4. Do not overturn back tilt knob when decreasing tension.
5. Dispose of packing material properly. Do not use plastic cover as head
covering. It may cause suffocation.
6. Do not use chair as a stepladder.
7. Use this chair for its intended purpose only.
8. Use mild detergent only for cleaning.
LIMITED WARRANTY
SPACE
®
chairs are warranted* from the date of purchase against failure due to material and workmanship as follows:
 •Lifetimeoncomponentpartsincludingpneumaticcylinder,controlmechanism,baseandcasters.
 •3Yearsonupholsteryfabricandfoamagainstwearanddeterioration.
 •Leatherisnotwarrantedagainstroutinescratchingandscufng,asleatherissubjecttominorblemishesinuse.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons weighing 250 lbs. or
less. This warranty will not cover labor, freight or damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other
event beyond the control of Office Star Products. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or
consequential damages is excluded. The user assumes all risk of injury resulting from use of this product. When usage is more than 40 hours per week, a five
year warranty on all parts applies. Fabric is warranted for one year. Thiswarrantygivesyouspeciclegalrights,andyoumayalsohaveotherrightswhichvary
from state to state.
To make a warranty claim, contact Parts Department via e-mail parts@officestar.net, by Fax [phone], or toll free parts
number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time. Provide model number and description of the
problem and obtain confirmation number. At it’s option Office Star Products will:
(a) Supply compatible components of current manufacture.
(b) Repair the customer’s component.
It is the customer’s responsibility to prepay freight on any components returned to the factory. Return freight on components
covered by warranty will be paid by Office Star Products.
1
FEATURES
• PNEUMATIC SEAT HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and lift lever (1) up. To lower seat
height sit on chair and lift lever (1) up.
NOTE: It is normal for chair to slightly lower under
body weight.
• INFINITE LOCKING 2-to-1 SYNCHRO KNEE TILT CONTROL
 Tolock,turnlever(4notshown)up.Tounlockandfreeoat,turnlever(4
not shown) down. Back reclines at twice the rate of the seat
• TILT ADJUSTMENT
Forindividualcomfort,thischairhasbeenequippedwithanadjustment
that will allow the user to change the tension of the tilting feature. Turn
knob (2) clockwise to increase tension and counter-clockwise to decrease
or ease the tension.
NOTE:Becarefulnottoloosentiltadjustmentknobcompletely.
• ARM HEIGHT ADJUSTMENT
Toadjustarmheight,pushbutton(3)intoallowthearmstomoveupor
down freely. Release the button (3) once the desired height is reached.
• HEADREST ADJUSTMENT
Toadjusttheheightoftheheadrest,rstloosentheadjustmentknobat
the back of the headrest by turning it counterclockwise. Do not over loosen
theadjustmentknob.Movetheheadresttoadesiredheightandtighten
theadjustmentknobbyturningitclockwise.Tomovetheheadrestforward
orbackwards,rstpullthesmallleversatthebackoftheheadresttoan
up-right position. Then move the headrest to a desired position and press
the levers down to horizontal to secure the position.
3
2
4
10
8
5
6
3
1
1
7L
7R
12
9
13
x3
x4
2
x3
x3
5
x5
13
4
4
3x
3x
13
11
11
8
ÉTAPE 1
ÉTAPE 4
ÉTAPE 2
ÉTAPE 5
ÉTAPE 3
PIèCE QTÉ
1. Base .......................1
2. Roulettes ....................5
3. Vérin pneumatique ............1
4. Mécanisme ...................1
5. Coussin du siège ..............1
6. Coussin du dossier ............1
7. Accoudoirs (7L et 7R) ..........2
8. Vis d’accoudoir ...............6
9. Vis de support de dossier .......3
10. Vis de mécanique ............4
11. Rondelles plates .............6
12. Support de dossier (préinstallé) . . 1
13. Clé Allen ...................1
Enlever toutes les pièces du carton, les organiser selon les numéros de pièce indiqués sur la liste et vous assurer que les quantités des pièces
sont correctes.
ÉTAPE 1Insérerlesroulettes(2)danslabase(1),etvousassurerquetouteslesroulettes(2)sontbieninsérées.
ÉTAPE 2Alignerlestroussurlesaccoudoirs(7Let7R)aveclestroussurlecoussindusiège(5).Fixerlesaccoudoirs(7Let7R)aucoussindusiège(5)avec
troisvisd’accoudoir(8)ettroisrondellesplates(11)pourchaqueaccoudoir.RESSERRER COMPLÈTEMENT TOUTES LES VIS D’ACCOUDOIR (8)
AVEC LA CLÉ ALLEN (13).
ÉTAPE 3Fixerlemécanisme(4)aucoussindusiège(5)aveclaècheversl’avantdusiège.Fixeravecquatrevisdemécanique(10).RESSERRER
COMPLÈTEMENT TOUTES LES VIS DE MÉCANIQUE (10) AVEC LA CLÉ ALLEN (13).
ÉTAPE 4Fixerlesupportdudossier(12)àl’arrièredelaplaquedusiège(4)avectroisvisdesupportdedossier(9).
RESSERRER COMPLÈTEMENT TOUTES LES VIS DE SUPPORT DE DOSSIER (9) AVEC LA CLÉ ALLEN (13).
ÉTAPE 5Insérerlevérinpneumatique(3)danslabase(1).Placerlesiègeassemblésurlevérinpneumatique(3)etmettredelapression.
ATTENTION : AVANT D’UTILISER LE FAUTEUIL, VOUS ASSURER D’AVOIR RESSERRÉ COMPLÈTEMENT
TOUTES LES VIS.