Audio Driver Installation Quick Start Guide Quick BIOS Setup Motherboard The SOYO CD Plus VIA 8237 Serial USB 2.
SOYO™ 1. AGP cards running at 3.3V are not supported; only AGP cards running at 1.5V can be used in this mainboard. 2. Please read the user guide before proceeding with your installations. Serious damage may occur if the procedure is not followed properly. 3. If you have any problem getting your system to work, please follow the troubleshooting tips in your user guide. 4. For immediate Technical questions, please visit http://www.soyousa.com/support and http://www.soyousa.com/kb.
SOYO™ SY-KT600 DRAGON Plus Motherboard AMD® K7 Athlon & DuronTM processors VIA KT600 AGP/PCI Motherboard 100/133/166/200 MHz Front Side Bus supported ATX Form Factor Copyright © 2003 by SOYO Computer Inc. Trademarks: SOYO is a registered trademark of SOYO Computer Inc. All trademarks are properties of their owners. Product Rights: All names of the product and corporate mentioned in this publication are used for identification purposes only.
1 Introduction Congratulations on your purchase of the SY-KT600 DRAGON Plus motherboard. This Quick Start Guide illustrates the steps for installing and setting up your new motherboard. This guide provides all users with the basic steps of motherboard setting and operation. For further information, please refer to the SY-KT600 DRAGON Plus motherboard User’s Manual that came with your motherboard.
Introduction SY-KT600 DRAGON Plus Quick Start Guide SY-KT600 DRAGON Plus Layout PS/2 KB PS/2 Mouse Connector Connector USB3 / USB4 COM A COM B PRT ATX Power FJ1 ABR USB1 / USB2 / LAN Line out / Front out 8 7 2 1 1 6 4 2 1 J30 MIC IN / Center & Bass out 3 Line in / Rear out AGP Slot CD-SPDIFO 1 2 1 4 PCI Slot #1 1 ITE IT8705F 4 PCI Slot #2 SATA2 □ PCI Slot #3 5 SATA1 VT8237 IDE 2 IDE 1 1 PCI Slot #4 SIRCON FDC1 VT6307 PCI Slot #5 5 10 FW1 1 5 1 6 10 FW2 6
Introduction SY-KT600 DRAGON Plus Quick Start Guide Key Features Supports AMD 462 pins Socket A processors: CPU Athlon XP (Palomino/Thoroughbred/Barton) (200/266/333/400 MHz FSB) Duron/Morgan Chipset Memory AMD® KT600/ 8237 Chipset Supports PC2100, PC2700 and PC3200 DDR (non-registered and ECC) memory modules. AGP 1x AGP master 4x/ 8x slot (1.
USB 2.0 8x USB 2.0 compliant ports (4x on rear IO panel, 4x pin headers.) IEEE 1394 Onboard VIA VT6307 IEEE1394 Firewire controller with 2x pin header Sound VT1616 6 channel Audio Codec 10/100 MBps 100Base-T Ethernet controller, supporting Wake-On-Lan (WOL) Power Failure resume function to allow the system to turn on or off after a power failure, which is indispensable for server systems.
SY-KT600 DRAGON Plus Quick Start Guide Hardware Installation 2 Installation To avoid damage to your motherboard, please follow these simple rules while handling this equipment: Before handling the motherboard, ground yourself by touching on to an unpainted portion of the system's metal chassis. Remove the motherboard from its anti-static packaging. Hold the motherboard by the edges and avoid touching its components. Check the motherboard for damage.
SY-KT600 DRAGON Plus Quick Start Guide We will now begin the installation process. Please follow the step-by-step procedure designed to lead you to a complete and correct installation. Step 1- Install the Central Processing Unit (CPU) Step 2- Install memory modules Step 3- Install expansion cards Step 4- Connect cables, case wires, and power supply Step 1.
SY-KT600 DRAGON Plus Quick Start Guide 5. Set the jumpers on the FJ1 jumper block to the correct FSB for your CPU. Hardware Installation FJ1 100 MHz Clock Select 133 MHz 36 25 14 6 5 4 166 MHz 200 MHz 36 25 14 3 6 2 5 1 4 3 2 1 RJ2 Dipswitch This dipswitch sets the ratio of your CPU. Note that this switch will only work if you have an unlocked CPU. SW： OFF=1 ON=0 RATIO UNDER 12.5 FID Codes for SW 1 ~ 7 Four-Bit Clock FID Multiplier Four-Bit Clock FID Multiplier 0000000 11.0 0000010 7.
SY-KT600 DRAGON Plus Quick Start Guide CPU Fan Installation Note: Remember to connect the fan to the appropriate power source. CPU Fan Mount Procedure: To prevent scratch or damage on the motherboard, please follow the instructions on how to mount the CPU fan properly. 1. Apply thermal paste to the die of the CPU. 11 Hardware Installation Your Socket A processor kit comes with a cooling fan. Mount the fan on the processor according to the instructions provided by the manufacturer.
SY-KT600 DRAGON Plus Quick Start Guide Hardware Installation 2. Carefully mount the fan on top of the CPU and clip-on the first lock. 1 3. Clip-on the second lock and please make sure not to damage/scratch the board.
SY-KT600 DRAGON Plus Quick Start Guide Hardware Installation 4. Connect the power connector to CPUFAN1. Note: If the fan is defective or Power connector is not connected to CPUFAN1, the system will enable Fan Off Control function. See below for more information on FOC function. When the CPU temperature exceeds, the temperature set in the CPU Temp. Protection in BIOS setup, SOYO’s Anti Burn Regulator (ABR) will automatically shutdown the system and beep until the power button is pressed for one time.
SY-KT600 DRAGON Plus Quick Start Guide Hardware Installation FOC (Fan-Off Control) The newly designed SOYO “FOC” is based on the concept of total protection for the CPU, which is very different from what is currently seen on the market. The H/W control function is used to see a passive security system of monitoring and warning. S/W Simultaneous Signal Follow-up techniques and Auto Power Off System are included to prevent possible damage caused by the malfunctioning of the CPU fan.
SY-KT600 DRAGON Plus Quick Start Guide SOYO's ABR (Anti Burn Regulator) is a specially designed hardware circuit that works hand in hand with the CPU’s internal sensor in monitoring the temperature of the CPU and prevent it from overheating. Once the heat accumulated in the CPU is over the set limit. ABR will automatically shut down the system power and warn you with a beeping sound. To de-activate the beeping sound, un-plug the AC power cord.
SY-KT600 DRAGON Plus Quick Start Guide Step 3. Installation of Expansion Cards Hardware Installation The motherboard has 1 AGP slot and 5 PCI slots. 1. Read the related expansion card’s instruction document before inserting the expansion card into the computer. 2. Press the expansion card firmly into expansion slot in the motherboard. 3. Make sure the metal contacts on the card are correctly seated in the slot. 4. Replace the screw to secure the slot bracket of the expansion card. 5.
Pin1 VCC Pin1 A0PC Pin1 Pin2 Data(-) Pin2 GND Pin3 Data(+) Pin3 B0PC Pin2 USB20_3 / USB20_4 Pin4 Pin6 Pin7 GND VCC Data(-) Pin3 Pin7 CGND Pin8 B0MC Pin9 PWR0 Pin10 CGND Pin4 1394: FW2 Pin5 Pin6 Pin7 Pin8 Pin9 Pin10 12V A1MC CGND B1MC PWR1 CGND CPU Cooling Fan: CPUFAN2 Pin1 Pin2 Pin3 SENSOR GND Chassis Fan: CHAFAN1 Pin1 Pin2 Pin3 GND 12V SENSOR Connect the CD Line-in cord from the CR-ROM CDIN1 device to the matching connector CDIN AUXIN1 HDD LED HDD LED Pin1 LED Anode Pin2 LED Cathod
SY-KT600 DRAGON Plus Quick Start Guide CMOS Clear (JP5) Hardware Installation In some cases the CMOS memory may contain wrong data, follow the steps below to clear the CMOS memory. 1. Clear the CMOS memory by momentarily shorting pin 2-3 on jumper JP5. Its white cap can easily identify this jumper. 2. Put the jumper back to 1-2 to allow writing of new data into the CMOS memory.
SY-KT600 DRAGON Plus Quick Start Guide 3 Quick BIOS Setup This motherboard allows you to change your memory and onboard peripheral settings in BIOS setup. After the hardware installation is complete, turn the power switch on, then press the key during the system diagnostic checks to enter the Award BIOS Setup program. The CMOS SETUP UTILITY will be shown on the screen. Then, follow these steps to configure your system.
SY-KT600 DRAGON Plus Quick Start Guide 4 The SOYO CD The SOYO-CD will Auto Run only in Windows Based Operating Systems. Your SY-KT600 DRAGON Plus motherboard comes with a CD-ROM labeled "SOYO CD." The SOYO CD contains a. The user's manual for your new motherboard in PDF format, b. The drivers software available for installation, and c. A database in HTML format with information on SOYO motherboards and other products. Step 1.
(SOYO CD Start Up Program Menu) Under Windows 95/98/ME, the SOYO CD Start Up Program automatically detects the SOYO motherboard the system uses and displays the corresponding model name. The user's manual files included on the SOYO CD are in PDF (Postscript Document format). In order to read a PDF file, the appropriate Acrobat Reader software must be installed in your system.
SY-KT600 DRAGON Plus Quick Start Guide Step 2. Install Drivers and Utilities Click the Install Drivers button to display the list of drivers software that can be installed with your motherboard. The Start Up program displays the drivers available for the particular model of motherboard you own. We recommend that you only install those drivers.
SY-KT600 DRAGON Plus Quick Start Guide VIA SerialATA driver for Win 98SE/ME/2000/XP This program is for install Driver to use Serial ATA function. VIA Onboard Audio Software for Win 98SE/ME/2000/XP This driver supports 2/4/6 speakers with 3D stereo enhancement. KT600 DRAGON Plus Hardware monitor for Win 98SE/ME/2000/ XP Your motherboard comes with a hardware monitoring IC. By installing this utility, Temperature, Fan speed and Voltages can be monitored.
SY-KT600 DRAGON Plus Quick Start Guide The SOYO CD After Windows XP installation, your device manager should look like this: 24
SY-KT600 DRAGON Plus Quick Start Guide The SOYO CD After driver installation, your Windows XP device manager should look like this: 25
SY-KT600 DRAGON Plus Quick Start Guide Drivers directory list in the CD driver Audio driver The SOYO CD Via 4 in 1 driver Onboard LAN RAID driver USB 2.
SY-KT600 DRAGON Plus Quick Start Guide 5 Audio Driver Installation Audio Driver Installation for Windows 98/98se After you have installed the audio driver, windows may prompt you to restart your computer. Audio Driver Installation When your computer has restarted it may look for the windows driver on your windows installation CD and ask you to insert your installation CD into your CD-drive. At this point you need to insert the windows installation CD into your CD-drive.
SY-KT600 DRAGON Plus Quick Start Guide 6 USB2.0 Driver Installation USB2.0 Driver Installation for Windows XP USB 2.0 drivers are available for download using Windows Update for Windows XP. For additional information regarding USB 2.0 support in Windows XP, please visit http://www.microsoft.com/hwdev/bus/USB/default.asp (Windows XP Service Pack1 Include USB2.0 Driver) After installing service pack1, please do the following: 1) Go into the device manager. 2) Remove ” ” 3) Restart your system. USB 2.
7 VIA 8237 Serial ATA Driver Installation You can use your VIA 8237 (SATA1,SATA2) as 1. Normal IDE function. 2. RAID function. (RAID0, 1) To use SATA1 and SATA2 as normal IDE, please do the following steps 1. Go to the CMOS setup SATA1,2” to enable. Integrated Peripherals VIA Onchip IDE device 2. Then set the SATA Mode to “IDE” 3. Install the VIA Serial ATA driver, see driver installation instruction below. “Onboard To use SATA1 and SATA2 as RAID controller, please do the following steps 1.
VIA 8237 Serial ATA Driver Installation SY-KT600 DRAGON Plus Quick Start Guide 8. Win XP will prompt you that a message that the driver is newer than the default driver, press S (use the driver on floppy) to continue. 9. The follow-on interface will list the devices to be installed, in which “VIA 8237 SATARaid SATARaid controller for windows XP” item should be included. (If users want to install other devices, press “S” at this time.) Press ENTER to continue Windows XP setup.
SY-KT600 DRAGON Plus Quick Start Guide Quick Trouble shooting tips Boot-up Issues The system does not power-up, no beeping sound heard and the CPU fan does not turn on. 1. Check if the power cord is plug into the power source. 2. Check if the power is connected to the M/B. 3. Check if the cable of the case power button is connected to the M/B power button connector (see Connectors and Plug-ins section in this Quick start guide for more info). 4. Make sure the power supply is not defective.
SY-KT600 DRAGON Plus Quick Start Guide Example. If you have a P4 M/B, you need to use a P4 power supply. 5. If you already checked the power supply specification, change the power supply it might be defective. The minimum is 350 watts AMD approved. When I boot up my system, everything works fine, it sees my CPU and memory, detects my hard drive, floppy drive and CD-ROM but locks up at "Verify DMI pool data... ". It doesn’t boot go any further. What should I do? 1. Clear CMOS battery.
SY-KT600 DRAGON Plus Quick Start Guide 3. If you still have the problem, remove all other add-on cards except for CPU/ Memory/ onboard Video/ Hard disk. See if you can finish Windows installation. Then put peripherals in one by one to identify which one causes the lockup. My system will not boot-up when I set my CPU to 133MHz FSB. It works with 100MHz FSB 1. Make sure to put some thermal paste on the CPU. 2. CPU might be defective. 3. Use an AMD approved power supply of at least 350 watts.
SY-KT600 DRAGON Plus Quick Start Guide VGA Issue After waking up from Suspend to RAM or Standby mode, the screen has no display but I can hear the hard disk operating 1. Install the VIA 4 in 1 driver set. 2. Check the VGA card manufacturer for a driver update (if using a different video card then the onboard video), and make sure the VGA card supports the Suspend to Ram function. 3. Update your VGA card’s BIOS (in the case of a video card other then the onboard video).
SY-KT600 DRAGON Plus Quick Start Guide The sound and everything else works fine except that the line-in and microphone do not work. What is wrong? 1. Please go to sound properties and check if the line-in and microphone in are enabled and not muted. 2. Check if the Microphone is ok. 3. When using 6 speakers the line-in and microphone channels are used for rear, center and bass. 6-Channel audio and microphone/line-in can not be used at the same time.
SY-KT600 DRAGON Plus Quick Start Guide How to contact us: If you are interested in our products, please contact the SOYO sales department in the region you live. If you require Technical Assistance, please contact our Technical Support in the region you live. SOYO prefers Email as communication medium, remember to always add to the email the country that you live in. TAIWAN SOYO COMPUTER INC. No. 21 Wu-Kung 5 Rd., Hsing Chuang City, Taipei Hsien, Taiwan, R.O.C.
Edition: August 2003 Version 1.
