8" METAL CUTTING BANDSAW MODEL SB1040 - SINGLE-PHASE MODEL SB1041 - THREE-PHASE OWNER'S MANUAL Hundreds of Thousands of Lathes Sold With a Tradition of Q uality Since 1906! Copyright © September, 2010 For Machines Mfg.
Scope of Manual This manual helps the reader understand the machine, how to prepare it for operation, how to control it during operation, and how to keep it in good working condition. We assume the reader has a basic understanding of how to operate this type of machine, but that the reader is not familiar with the controls and adjustments of this specific model. As with all machinery of this nature, learning the nuances of operation is a process that happens through training and experience.
Table of Contents INTRODUCTION ...............................................................3 About This Machine ............................................. 3 Capabilities ......................................................... 3 Features .............................................................. 3 Identification ........................................................ 4 Machine Specifications ........................................ 5 SAFETY..........................................................
SERVICE........................................................................... 41 Blade Tracking ................................................... 41 Table Calibration ............................................... 41 Guide Post Alignment........................................ 42 Bevel Gear Backlash.......................................... 43 Leadscrew End Play .......................................... 43 TROUBLESHOOTING ................................................. 44 ELECTRICAL .............
For Machines Mfg. Since 8/09 INTRODUCTION Model SB1040/SB1041 INTRODUCTION About This Machine Capabilities Features This 18" Metal-Cutting Bandsaw allows you to make exterior and interior contoured or straight cuts. Now that you know the basics of what this machine can do, take a minute to consider its features. To better understand these capabilities, imagine making a "doughnut" out of 1" steel plate: This machine is equipped with a built-in air blower near the blade guides.
Model SB1040/SB1041 INTRODUCTION For Machines Mfg. Since 8/09 Identification Blade Tension Handwheel Operation Controls Guide Post Elevation Knob FPM Display Electrical Control Box Work Lamp Welding Area Air Blower Blade Shear Lever Grinder Table Table Trunnions Variable Speed Handwheel Front View Serious personal injury could occur if you connect the machine to power before completing the setup process. DO NOT connect power until instructed to do so later in this manual.
For Machines Mfg. Since 8/09 INTRODUCTION Model SB1040/SB1041 Machine Specifications 0RGHO 6% 6RXWK %HQG 9HUWLFDO %DQGVDZ 3+ 2TQFWEV &KOGPUKQPU 9GKIJV NDU 9KFVJ UKFG VQ UKFG Z &GRVJ HTQPV VQ DCEM Z *GKIJV Z Z KP (QQVRTKPV .
Model SB1040/SB1041 INTRODUCTION For Machines Mfg.
For Machines Mfg. Since 8/09 INTRODUCTION Model SB1040/SB1041 0RGHO 6% 6RXWK %HQG 9HUWLFDO %DQGVDZ 3+ 2TQFWEV &KOGPUKQPU 9GKIJV NDU 9KFVJ UKFG VQ UKFG Z &GRVJ HTQPV VQ DCEM Z *GKIJV Z Z KP (QQVRTKPV .
Model SB1040/SB1041 INTRODUCTION For Machines Mfg.
For Machines Mfg. Since 8/09 SAFETY Model SB1040/SB1041 SAFETY Understanding Risks of Machinery Operating all machinery and machining equipment can be dangerous or relatively safe depending on how it is installed and maintained, and the operator's experience, common sense, risk awareness, working conditions, and use of personal protective equipment (safety glasses, respirators, etc.). The owner of this machinery or equipment is ultimately responsible for its safe use.
Model SB1040/SB1041 SAFETY For Machines Mfg. Since 8/09 5. Entanglement: Loose clothing, gloves, neckties, jewelry or long hair may get caught in moving parts, causing entanglement, amputation, crushing, or strangulation. Reduce this risk by removing/securing these items so they cannot contact moving parts. 11. Chuck Keys or Adjusting Tools: Tools used to adjust spindles, chucks, or any moving/ rotating parts will become dangerous projectiles if left in place when the machine is started.
For Machines Mfg. Since 8/09 SAFETY Model SB1040/SB1041 Additional Metal Cutting Bandsaw Safety 1. Blade Condition: Do not operate with a 7. Magnesium Fire Hazard: Use EXTREME CAUTION if cutting magnesium. Using the wrong cutting fluid or overheating the material could lead to an extremely hot fire that is difficult to extinguish. Additionally, do not allow magnesium swarf or dust to pile up around the machine and only dispose of the waste using approved methods. 8.
Model SB1040/SB1041 P R E PA R AT I O N For Machines Mfg. Since 8/09 PREPARATION Preparation Overview Things You'll Need The purpose of the preparation section is to help you prepare your machine for operation. The list below outlines the basic process. Specific steps for each of these points will be covered in detail later in this section. The typical preparation process is as follows: 1. Unpack the machine and inventory the contents of the box/crate. 2. Clean the machine and its components. 3.
For Machines Mfg. Since 8/09 P R E PA R AT I O N Power Supply Requirements Availability Before installing the machine, consider the availability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed. To minimize the risk of electrocution, fire, or equipment damage, installation work and electrical wiring must be done by a qualified electrician in accordance with all applicable codes and standards.
Model SB1040/SB1041 P R E PA R AT I O N SB1041 Circuit Requirements This machine is prewired to operate on a 220V power supply circuit that has a verified ground and meets the following requirements: Nominal Voltage ......................................... 220V Cycle .............................................................60 Hz Phase ....................................................... 3-Phase Circuit Rating....................................... 15 Amps Plug/Receptacle Type .....................
For Machines Mfg. Since 8/09 P R E PA R AT I O N Improper connection of the equipment-grounding wire can result in a risk of electric shock. The wire with green insulation (with or without yellow stripes) is the equipment-grounding wire. If repair or replacement of the power cord or plug is necessary, do not connect the equipmentgrounding wire to a live (current carrying) terminal.
Model SB1040/SB1041 P R E PA R AT I O N For Machines Mfg. Since 8/09 Cleaning & Protecting The unpainted surfaces are coated at the factory with a heavy-duty rust preventative that prevents corrosion during shipment and storage. The benefit of this rust preventative is that it works very well. The downside is that it can be time-consuming to thoroughly remove. Be patient and do a careful job when cleaning and removing the rust preventative.
P R E PA R AT I O N For Machines Mfg. Since 8/09 Model SB1040/SB1041 Weight Load Location Physical Environment The physical environment where your machine is operated is important for safe operation and longevity of parts. For best results, operate this machine in a dry environment that is free from excessive moisture, hazardous or flammable chemicals, airborne abrasives, or extreme conditions.
Model SB1040/SB1041 P R E PA R AT I O N Lifting & Moving This machine and its parts are heavy! Serious personal injury may occur if safe moving methods are not used. To reduce the risk of a lifting or dropping injury, ask others for help and use power equipment. Make sure the lifting eye shown in Figure 7 is completely threaded into the headstock, then lift the machine off the pallet and onto a suitable location using the lifting eye. For Machines Mfg.
For Machines Mfg. Since 8/09 P R E PA R AT I O N Machine Mounts Machine mounts are rubber pads mounted to a threaded stud, which can be fastened to the bottom of the machine. Machine mounts offer certain advantages such as ease of installation, vibration dampening, and easy leveling. They also make it easier to relocate the machine later on. The disadvantage of machine mounts is that the machine can shift or move over time.
Model SB1040/SB1041 P R E PA R AT I O N Power Connection Electrocution or fire may occur if machine is ungrounded, incorrectly connected to power, or connected to an undersized circuit. Use a qualified electrician to ensure a safe power connection. 3. Locate the power transformer in the electrical panel (see Figure 56 on Page 54). Remove the wire attached to the 110V terminal and connect it to the 220V terminal. 4.
For Machines Mfg. Since 8/09 P R E PA R AT I O N Test Run After all preparation steps have been completed, the machine and its safety features must be tested to ensure correct operation. If you discover a problem with the operation of the machine or its safety components, do not operate it further until you have resolved the problem. Note: Refer to Troubleshooting on Page 44 for solutions to common problems that occur with all metal bandsaws.
Model SB1040/SB1041 O P E R AT I O N OPERATION Operation Overview The purpose of this overview is to provide the novice machine operator with a basic understanding of how the machine is used during operation, so they can more easily understand the controls discussed later in this manual. 4. Adjusts the upper blade guide height to approximately 1⁄8"–1⁄4" above the workpiece for maximum blade support. 5.
O P E R AT I O N For Machines Mfg. Since 8/09 L. Controls Welder's Lamp Switch: Illuminates welding station when turned ON. Refer to Figures 10–12 and the following descriptions to become familiar with the basic controls of this machine. A. Model SB1040/SB1041 M. Variable Speed Handwheel: Adjusts blade speed from 88 to 384 FPM. Motor Light: Lights when the ON button is pressed and there is power to the machine. B. ON Button: Turns the main motor ON. C. OFF Button: Turns the main motor OFF. D.
O P E R AT I O N Model SB1040/SB1041 Blade Length Blade Selection Selecting the right blade for the cut requires a knowledge of various blade characteristics. A Blade Width Measured from the back of the blade to the tip of the blade tooth (the widest point), blade width is often the first consideration given to blade selection.
O P E R AT I O N For Machines Mfg. Since 8/09 Model SB1040/SB1041 Tooth Set Three common tooth sets are alternate, wavy, and raker (see Figure 15). Each removes material in a different manner to make the kerf in the workpiece. Standard (or Raker) Raker Wavy Alternate Variable Pitch (VP) Variable Pitch Positive Rake Hook (or Claw) Figure 15. Bandsaw blade tooth sets. Alternate: An all-purpose arrangement of Skip (or Skip Tooth) bending the teeth evenly left and right of the blade.
O P E R AT I O N Model SB1040/SB1041 Blade Pitch (TPI) The chart below is a basic starting point for choosing teeth per inch (TPI) for variable pitch blades and standard raker set bi-metal blades/ HSS blades. However, for exact specifications of bandsaw blades that are correct for your operation, contact the blade manufacturer. To select the correct blade pitch: 1. Measure the material thickness.
For Machines Mfg. Since 8/09 O P E R AT I O N Note: Excessive blade contact with the wheel Blade Changes ! flange during operation could lead to blade and wheel damage. Always disconnect power to the machine when changing blades. Failure to do this may result in serious personal injury. All saw blades are dangerous and may cause personal injury. To reduce the risk of being injured, wear leather gloves when handling saw blades. 6.
Model SB1040/SB1041 O P E R AT I O N For Machines Mfg. Since 8/09 Blade Breakage Blade Care & Break-In Many conditions may cause a bandsaw blade to break. Blade breakage is unavoidable, in some cases, since it is the natural result of the peculiar stresses that bandsaw blades must endure. Blade breakage is also due to avoidable circumstances. Avoidable blade breakage is most often the result of poor care or judgment on the part of the operator when mounting or adjusting the blade or support guides.
O P E R AT I O N For Machines Mfg. Since 8/09 Model SB1040/SB1041 Blade Speed Chart The chart in Figure 19 offers blade speed guidelines for various metals, given in feet per minute (FPM) and meters per minute (M/Min). Choose the closest available speed on the machine, then adjust the feed rate as necessary, using the appearance of the chips produced as a guide.
O P E R AT I O N Model SB1040/SB1041 For Machines Mfg. Since 8/09 Positioning Guide Post Adjusting Blade The guide post assembly is used for two Guides purposes: 1) To properly position the blade guard to protect the operator from the exposed blade between the workpiece and the upper wheel housing, and 2) to position the upper blade guides close to the workpiece for maximum blade support. The blade guides provide side-to-side and rear support to keep the blade straight while cutting.
For Machines Mfg. Since 8/09 O P E R AT I O N Blade Support Cap Screw ! Blade Support ! Blade Guide Bracket Cap Screw Figure 23. Lower blade guides and bracket. 5. Model SB1040/SB1041 Position the blade guides so that they are approximately 1⁄16" behind the tooth gullets (see Figure 24), then re-tighten the blade guide bracket cap screw. Figure 25. Blade guide assembly (upper assembly shown without blade for clarity). 7.
O P E R AT I O N Model SB1040/SB1041 For Machines Mfg. Since 8/09 Tilting Table Blade Welding The bandsaw table tilts 15° to the left and 15° to the right for basic cut angles, and 10° to the front and 10° to the back for feed angles. When used together, compound angled cuts can be made. Being able to quickly and safely weld a bandsaw blade comes in handy for the following situations: s 4O RE JOIN A BLADE THAT HAS BEEN PURPOSELY cut for making an internal contour cut.
For Machines Mfg. Since 8/09 O P E R AT I O N Note: To make a proper blade weld, the ends of the blade must be evenly butted together during the welding process. If necessary, use the grinder to square up the ends or remove any teeth that are in the welding zone (see Figures 29–30). Model SB1040/SB1041 5. Loosen the welding clamps by pulling the lock levers down. 6.
Model SB1040/SB1041 O P E R AT I O N Place the other blade end in the opposite welding clamp and position it so that it evenly butts up against the opposing blade end, then lock it in place by rotating the lock lever all the way up, as shown in Figure 33. 8. Note: For a good blade weld, it is critical that the For Machines Mfg. Since 8/09 11. Inspect the weld. The welded joint should be even across the width of the blade with no gaps (see Figure 34).
For Machines Mfg. Since 8/09 O P E R AT I O N 13. Press and hold the annealing button until the weld zone turns the appropriate color, then release the button. Note: If you cannot get the proper annealing color from the blade manufacturer, use the recommendations below as a baseline and experiment from there. —Carbon Steel ..................... Dull Cherry Red —Carbon Steel Hard Back ...................... Blue —Bi-Metal ........................................... Orange —High Speed Steel ..............
O P E R AT I O N Model SB1040/SB1041 Circle Cutting Jig The Model SB1040/SB1041 includes a jig that attaches to the guide post to provide an easy and accurate method for cutting circular shapes. 4. Install a blade with the proper width for radius of the circle you want to cut, using Figure 14 on Page 24 as a guide. 5.
For Machines Mfg. Since 8/09 MAINTENANCE Model SB1040/SB1041 MAINTENANCE Maintenance Schedule ! Chip Brush Always disconnect machine from power before performing maintenance or serious personal injury may result. For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructions given in this section. Daily: s s s s s s #HECK CORRECT LOOSE MOUNTING BOLTS Check/correct damaged or dull saw blade. Check/correct worn or damaged wires.
MAINTENANCE Model SB1040/SB1041 Lubrication The bearings on your bandsaw are factory lubricated and sealed. Leave them alone unless they need to be replaced. When needed, brush a light coat of multi-purpose grease on the blade tension leadscrew (see Figure 40). ! For Machines Mfg. Since 8/09 If the table becomes difficult to tilt, position it so that you can brush a thin coat of multi-purpose grease on the trunnion sliding surfaces (see Figure 42), then move the table back and forth to distribute.
For Machines Mfg. Since 8/09 MAINTENANCE Model SB1040/SB1041 V-Belts Note: When the machine is started, the belts will automatically adjust to the correct tension. To ensure optimum power transfer from the motor to the blade, the V-belts must be in good condition and operate under proper tension. Sprocket Drive Belt Check V-belt tension at least every three months—more often if the bandsaw is used daily. V-belts stretch with use and must be periodically re-tensioned.
Model SB1040/SB1041 MAINTENANCE Machine Storage All machinery will develop serious rust problems and corrosion damage if it is not properly prepared for storage. If decommissioning this machine, use the steps in this section to ensure that it remains in good condition. Note: If the machine will be out of service for only a short period of time, use way oil or a good grade of medium-weight machine oil (not auto engine oil) in place of the grease or rust preventative. 3.
SERVICE For Machines Mfg. Since 8/09 SERVICE Model SB1040/SB1041 Blade Tracking Table Calibration A blade that is tracking correctly runs cooler, reduces wear-and-tear on the machine, and increases cutting performance. When tracking correctly, the blade rides next to, but not against, the wheel flange. The tracking is controlled by adjusting the upper wheel.
Model SB1040/SB1041 5. SERVICE Tilt the table until the blade and table top are perpendicular, then tighten the trunnion cap screws. 6. Loosen the scale pointer for the cut angle scale (on the trunnion) and point it to zero. 7. Loosen the feed angle cap screw and place the machinist's square against the back of the blade. 8. Position the table perpendicular to the blade. 9. Tighten the feed angle cap screws. For Machines Mfg. Since 8/09 ! Guide Post Receiver 10.
SERVICE For Machines Mfg. Since 8/09 Model SB1040/SB1041 Bevel Gear Backlash Leadscrew End Play During the life of the machine, the variable speed handwheel may develop extra backlash due to normal wear of the bevel gears. If this lash becomes unacceptable, use this procedure to reduce the backlash.
TROU B LESHOOTI NG Model SB1040/SB1041 TROUBLESHOOTING For Machines Mfg. Since 8/09 Troubleshooting If you need replacement parts, or if you are unsure how to do any of the solutions given here, feel free to call us at (360) 734-1540. Symptom Machine does not start. Possible Cause Possible Solution 1. Power supply switched off/has incorrect voltage. 1. Switch power supply on/verify voltage. 2. Blown fuse/tripped circuit breaker at main panel. 2.
For Machines Mfg. Since 8/09 TROU B LESHOOTI NG Model SB1040/SB1041 Symptom Possible Cause Vibration when operating or cutting. 1. Loose or damaged blade. 1. Tighten or replace blade. 2. Worn wheel bearing. 2. Check/replace wheel bearing. 3. Wheels are not coplanar. 3. Adjust wheels so they are parallel and aligned. 4. Wheel tires worn or incorrectly installed. 4. Replace or dress rubber tires. 5. Bent or dull blade. 5. Replace blade. 6. Wheels out of balance. 6. Replace wheels.
TROU B LESHOOTI NG Model SB1040/SB1041 Symptom Machine or blade bogs down in the cut. Possible Cause For Machines Mfg. Since 8/09 Possible Solution 1. Excessive load on the blade. 1. Reduce feed rate or increase blade speed (see Page 29). 2. V-belts loose; belt squeals at times. 2. Tighten V-belts(see Page 39). 3. V-belts worn and slips. 3. Replace V-belts (see Page 39). 4. Blade is loading up. 4. Install a blade with more suitable TPI or different style of teeth. 5.
For Machines Mfg. Since 8/09 Symptom Blade tracks incorrectly, or comes off wheels. TROU B LESHOOTI NG Possible Cause Model SB1040/SB1041 Possible Solution 1. Feed rate is too fast. 1. Reduce feed rate, or decrease blade TPI. 2. Blade is not tracking correctly. 2. Adjust blade tracking (see Page 41). 3. Blade is bell-mouthed. 3. Install new blade, and regularly remove tension from blade when not in use (see Page 27). 4. Blade is dull, wanders, and gets pinched in the cut. 4.
Model SB1040/SB1041 ELECTRICAL For Machines Mfg. Since 8/09 ELECTRICAL Electrical Safety Instructions These pages are accurate at the time of printing. In the constant effort to improve, however, we may make changes to the electrical systems of future machines. Study this section carefully. If you see differences between your machine and what is shown in this section, call Technical Support at (360) 734-1540 for assistance BEFORE making any changes to the wiring on your machine. 1.
For Machines Mfg. Since 8/09 ELECTRICAL Model SB1040/SB1041 Wiring Overview A CONTROL PANEL A E WORK LAMP See Page 50 and Figure 54.
ELECTRICAL Model SB1040/SB1041 For Machines Mfg.
ELECTRICAL For Machines Mfg. Since 8/09 Model SB1040/SB1041 SB1040 110V Electrical Panel, Motor & Cord F ELECTRICAL PANEL 0V 1 T R 4 R TRANSFORMER R Class: B Capacity: 110VA 1-Ph 50/60Hz Primary Voltage: 0V/110V/220V 3 110V R T 220V 2 2 T T 1 GND A1 4 A2 1 1 1 L1 3L2 5L3 13NO 4 400 3 3 C16 1 2T1 4T2 6T3 14NO Reset 11 15 19 7 23 5.
ELECTRICAL Model SB1040/SB1041 For Machines Mfg. Since 8/09 SB1040 220V Motor Rewire SB1040 220V Electrical Panel, Motor & Cord F ELECTRICAL PANEL 0V 1 T R 4 R TRANSFORMER R Class: B Capacity: 110VA 1-Ph 50/60Hz Primary Voltage: 0V/110V/220V 3 110V R T 220V 2 2 T T 1 GND A1 4 A2 1 1 1 L1 3L2 5L3 13NO 4 400 3 3 C16 1 2T1 4T2 6T3 14NO Reset 11 15 19 7 23 5.
ELECTRICAL For Machines Mfg. Since 8/09 Model SB1040/SB1041 SB1041 220V Electrical Panel, Motor & Cord F ELECTRICAL PANEL 1 T 0V TRANSFORMER Class: B Capacity: 110VA 1-Ph 50/60Hz Primary Voltage: 0V/110V/220V 110V 220V 2 1 12 11 10 9 U V W S 2 T 1 E 4 A2 W 3 A1 V S 1 L1 3L2 5L3 13NO 3 16 U R T 400 3.
Model SB1040/SB1041 ELECTRICAL For Machines Mfg. Since 8/09 Electrical Component Pictures Electrical Pictures FPM Sensor Terminal Strip Motor Junction Box Welding Transformer Figure 55. Welding Panel. Power Transformer Main Terminal Block Figure 53. Motor and FPM sensor. Overload Relay Control Panel FPM Display Welder's Lamp Figure 54. Control Panel, FPM Display & Welder's Lamp. -54- Figure 56. Electrical Box.
38 44 43 42 45 45 13 16 30 32 32 31 33 35 32 2 32 3 35 34 34 41 32 32 36 40 38 37 24 25 27 26 34 32 39 32 12 11 23 29 17 20 28 18 21 22 23 24 19 11 46 4 1 11 2 10 6 5 7 3 2 9 8 PARTS 14 15 32 44 43 For Machines Mfg.
Model SB1040/SB1041 PARTS For Machines Mfg. Since 8/09 Bottom Frame Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 PSB1040001 PB07M PW01M PSB1040004 PN06M PS03M PSB1040007 PS05M SB1321 PSB1040010 PLW04M PSB1040012 PCAP31M PSB1040014 PSB1040015 PSB1040016 PS16M PRIV014M PSB1040019 PCAP31M PSB1040021 PSB1040022 PW03M BOTTOM REAR VENTED COVER HEX BOLT M8-1.25 X 25 FLAT WASHER 8MM BOTTOM FRAME HEX NUT M5-.
124-3 124-4 SB1040 Only 124-5 124 124-1 124-2 180 131 125 110 119 128 179 135 132 130 139 126 151 127 105 104 111 134 133 118 134 133 129 108 109 107 112 106 113 117 106 114 104 110 102 123 116 115 101 104 105 103 109 141 140 146 134 152 151 153 139 154 157 145 109 136 127 128 148 138 155 137 147 144 143 142 181 136 119 121 122 120 175 139 127 148 150 176 127 164 127 128 139 172 161 137 166 178 150 162 127 177 128 127 164 163 166 12
Model SB1040/SB1041 PARTS For Machines Mfg.
209 219 221 230 236 229 227 228 232 234 225 226 238 220 209 224 223 219 208 214 211 212 213 217 209 216 215 218 222 217 206 204 207 203 237 205 245 204 203 240 238 239 290 243 251 291 255 268 259 278 257 267 256 273 265 266 267 258 205 274 263 262 264 252 253 242 250 241 247 248 249 254 235 239 236 244 233 231 246 270 269 271 260 261 275 289 279 283 282 284 287 282 288 276 277 280 281 276 278 284 285 280 286 210 282 283 PARTS 202 203 2
Model SB1040/SB1041 PARTS For Machines Mfg.
PARTS For Machines Mfg.
-62- 425 410 414 412 410 413 408 409 405 407 406 401 404 403 415 418 427 417 418 432 431 428 428 428 426 417 415 416 429 421 420 433 423 424 424 433 449 446 465 440 454 464 448 462 466 450 445 452 451 460 459 461 419 453 463 434 436 437 458 440 433 455 456 457 437 435 438 442 441 422 437 440 420 446 433 447 445 444 443 439 435 434 436 PARTS 430 419 410 411 402 Model SB1040/SB1041 For Machines Mfg.
For Machines Mfg.
Model SB1040/SB1041 PARTS For Machines Mfg. Since 8/09 Digital Tachometer System 509 501 502 503 504 506 505 508 507 REF PART # DESCRIPTION REF PART # DESCRIPTION 501 502 503 504 505 PN03M PS16M PS113M PSB1040504 PS68M HEX NUT M8-1.25 PHLP HD SCR M8-1.
PARTS For Machines Mfg. Since 8/09 Model SB1040/SB1041 Electrical Cabinet 601 602 604 605 603 606 REF PART # DESCRIPTION REF PART # DESCRIPTION 601 602 603 604 PSB1040601 PSB1040602 PSB1040603 PSB1040604 ELECTRICAL BACKBOARD TRANSFORMER YA CHANG 220V 1A TERMINAL BLOCK 4 POST CONTACTOR AB 100-C16-400 110V (SB1040) 604 605 605 606 PSB1041604 PSB1040605 PSB1041605 PSB1040606 CONTACTOR AB 100-C09-400 110V (SB1041) OL RELAY AB 193-EEEB 5.4 – 27A (SB1040) OL RELAY AB 193-EEDB 3.
PARTS Model SB1040/SB1041 For Machines Mfg. Since 8/09 Circle Cutting Jig 618 612 611 619 613 615 614 614 621 620 621 617 614 616 624 626 615 622 613 623 613 613 613 625 REF PART # DESCRIPTION REF PART # DESCRIPTION 611 612 613 614 615 616 617 618 PCAP31M PLW04M PSS20M PN02M PSS20M PCAP13M PLW04M PSB1040618 CAP SCREW M8-1.25 X 25 LOCK WASHER 8MM SET SCREW M8-1.25 X 8 HEX NUT M10-1.5 SET SCREW M8-1.25 X 8 CAP SCREW M8-1.
WAR R ANT Y For Machines Mfg. Since 8/09 Model SB1040/SB1041 Machine Labels 704 MODEL SB1041 18" VARIABLE SPEED METAL CUTTING BANDSAW ! WARNING! 702 703 ! WARNING! ! WARNING! 701 INJURY HAZARD Do not use machine if you have not read the manual. Visit southbendlathe.com or call 360-734-1540 to get a manual.
Model SB1040/SB1041 -68- NOTES For Machines Mfg.
For Machines Mfg. Since 8/09 WARRANTY & RETURNS WAR R ANT Y Model SB1040/SB1041 Warranty This quality product is warranted by South Bend Lathe Company to the original buyer for one year from the date of purchase. This warranty does not apply to consumable parts, or defects due to any kind of misuse, abuse, negligence, accidents, repairs, alterations or lack of maintenance. We do not reimburse for third party repairs.
Printed In Taiwan #JB13203
